"gpmc,sync-clki-ps" is not defined/documented, it should be
"gpmc,sync-clk-ps" instead.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

The On Chip Peripherals (OCP) device node is a simplified
representation of the AM33XX SoC interconnect. An OCP dev
node is already defined in the am33xx.dtsi Device Tree
source file included by am33xx based boards so there is
no need to redefine this on each board DT file.

Also, the OCP and IP modules directly connected to it are SoC
internal details that is better to keep outside of board files.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

am33xx boards DTS include the am33xx.dtsi Device Tree
source file that already define a pinmux device node for
the AM33XX SoC Pin Multiplex.

Redefining this for each board makes the Device Tree files
harder to modify and maintain so let's just use what is
already defined in the included .dtsi file.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

This matches the vendor 3.8.x configuration that is shipping
with the boards.

The LED layout is now:
 USR0: heartbeat
 USR1: mmc0 (micro-SD slot)
 USR2: cpu0
 USR3: mmc1 (eMMC)

The cpu0 triggers was put in between the mmc triggers to make
is easier to see where the disk activity is.
Signed-off-by: NKoen Kooi <koen@dominion.thruhere.net>
Tested-by: NKevin Hilman <khilman@linaro.org>
Reviewed-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

The micro-SD slot hooks up all four data pins so lets' use them.
Signed-off-by: NKoen Kooi <koen@dominion.thruhere.net>
Tested-by: NKevin Hilman <khilman@linaro.org>
Reviewed-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

The pinmux is specified in am335x-bone-common.dtsi to be
reused by the eMMC cape.
Signed-off-by: NKoen Kooi <koen@dominion.thruhere.net>
Tested-by: NKevin Hilman <khilman@linaro.org>
Reviewed-by: NNishanth Menon <nm@ti.com>
[bcousson@baylibre.com: Fix traling spaces and useless comments]
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

This enables the use of MMC cards even when no card was inserted at boot.
Signed-off-by: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NKoen Kooi <koen@dominion.thruhere.net>
Tested-by: NKevin Hilman <khilman@linaro.org>
Reviewed-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Adds AM33XX MMC support for am335x-bone, am335x-evm and am335x-evmsk boards.

Also added is the DMA binding definitions based on the generic DMA request
binding.

Additional changes made to DTS:
* Interrupt, reg and compatible properties added
* ti,needs-special-hs-handling added
Signed-off-by: NMatt Porter <mporter@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NJoel Fernandes <joelf@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Adds DMA resources to the AM33XX SPI nodes.
Signed-off-by: NMatt Porter <mporter@ti.com>
Signed-off-by: NJoel A Fernandes <joelagnel@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Adds AM33XX EDMA support to the am33xx.dtsi as documented in
Documentation/devicetree/bindings/dma/ti-edma.txt

[Joel Fernandes <joelf@ti.com>]
Drop DT entries that are non-hardware-description as discussed in [1]

[1] https://patchwork.kernel.org/patch/2226761/Signed-off-by: NMatt Porter <mporter@ti.com>
Signed-off-by: NJoel A Fernandes <joelagnel@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Without this node, there will be no palmas driver to notify
dwc3 that a cable has been connected and, without that, dwc3
will never initialize.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
[kishon@ti.com: added dt properties for enabling vbus/id interrupts
and fixed vbus-supply value after SMPS10 is modeled as 2 regulators]
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Use a common naming scheme "mode0name.modename flags" for the
USB host pins to be consistent.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

This adds devicetree for gta04 (Openmoko next generation board) with necessary
support for mmc, usb, leds and button.
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Populate uarts, timers, rtc, wdt, gpio, i2c, spi, cpsw & pwm nodes.

Reason for adding these nodes early - hwmod code required address
space of peripherals corresponding to these nodes (as address space
details are removed from hwmod database).

uart0, timers - 1 & 2 and synctimer were already present, so here the
remaining uarts & timers are added.

All properties as per the existing binding has been added for uart,
timer, rtc, wdt & gpio. Even though that was not the current scope
of work, felt adding those would reduce or require no effort later
to get these peripherals working.

For i2c, spi, cpsw & pwm - only the properties that were sure to be
correct has been added (main intention is to make hwmod happy and
avoid any later modification to here added properties).

While at it add "ti,hwmod" property to already existing nodes.
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Update AM4372 cpu node to the latest cpus/cpu bindings for ARM.
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Acked-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add minimal device tree source needed for DRA7 based SoCs.
Also add a board dts file for the dra7-evm (based on dra752)
which contains 1.5G of memory with 1G interleaved and 512MB
non-interleaved. Also added in the board file are pin configuration
details for i2c, mcspi and uart devices on board.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

The OMAP4 SoC family uses specially-designed PMIC (power management IC)
companion chip for power management needs: TWL6030/TWL6032.
Therefore there is a typical connection of PMIC to OMAP4 so we can
move it into separate .dtsi file and do not duplicate over
board-specific files.

Tested on OMAP4 SDP board and Pandaboard ES2.
Signed-off-by: NRuslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

SMPS10 has two outputs OUT1 and OUT2. Hence SMPS10 is modeled as
two regulators. The DT node is split to reflect it.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Following commit ff5c9059 and therefore other omap platforms using
the gpio-omap driver correct the #interrupt-cells property on am33xx
too. The omap gpio binding documentaion also states that
the #interrupt-cells property should be 2.
Signed-off-by: NLars Poeschel <poeschel@lemonage.de>
Reviewed-by: NJavier Martinez Canillas <javier@dowhile0.org>
Acked-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

ARM Performance Monitor Units are available on the am33xx,
add the support in the dtsi.

Tested with perf and oprofile on a regular beaglebone.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

The IGEP COM MOdule has a GPIO LED connected to OMAP
pins. Configure this pin as output GPIO.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

The IGEPv2 has a number of GPIO LED connected to OMAP
pins. Configure these pins as output GPIO.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

IGEP boards have a number of LED connected to OMAP or TWL GPIO
lines. The actual wiring is different on each board so each board
DT has need to configure the mux correctly.

Even though it works with the current DT, the kernel complains with:

[2.305023] leds-gpio leds.18: pins are not configured from the driver

Add an empty pinmux_leds_pins pinctrl child node so boards can
override with the correct mux configuration and not depend on
default values for the GPIO LEDs to work.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

This adds device tree with necessary support to boot with functional
video (on both emulator and real N900 device).
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Modify the code to use current_euid(), and in_egroup_p, as in done
in fs/proc/proc_sysctl.c:test_perm()

Cc: stable@vger.kernel.org
Reviewed-by: NEric Sandeen <sandeen@redhat.com>
Reported-by: NEric Sandeen <sandeen@redhat.com>
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull SCSI target fixes from Nicholas Bellinger:
 "Here are the outstanding target fixes queued up for v3.12-rc4 code.

  The highlights include:

   - Make vhost/scsi tag percpu_ida_alloc() use GFP_ATOMIC
   - Allow sess_cmd_map allocation failure fallback to use vzalloc
   - Fix COMPARE_AND_WRITE se_cmd->data_length bug with FILEIO backends
   - Fixes for COMPARE_AND_WRITE callback recursive failure OOPs + non
     zero scsi_status bug
   - Make iscsi-target do acknowledgement tag release from RX context
   - Setup iscsi-target with extra (cmdsn_depth / 2) percpu_ida tags

  Also included is a iscsi-target patch CC'ed for v3.10+ that avoids
  legacy wait_for_task=true release during fast-past StatSN
  acknowledgement, and two other SRP target related patches that address
  long-standing issues that are CC'ed for v3.3+.

  Extra thanks to Thomas Glanzmann for his testing feedback with
  COMPARE_AND_WRITE + EXTENDED_COPY VAAI logic"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  iscsi-target; Allow an extra tag_num / 2 number of percpu_ida tags
  iscsi-target: Perform release of acknowledged tags from RX context
  iscsi-target: Only perform wait_for_tasks when performing shutdown
  target: Fail on non zero scsi_status in compare_and_write_callback
  target: Fix recursive COMPARE_AND_WRITE callback failure
  target: Reset data_length for COMPARE_AND_WRITE to NoLB * block_size
  ib_srpt: always set response for task management
  target: Fall back to vzalloc upon ->sess_cmd_map kzalloc failure
  vhost/scsi: Use GFP_ATOMIC with percpu_ida_alloc for obtaining tag
  ib_srpt: Destroy cm_id before destroying QP.
  target: Fix xop->dbl assignment in target_xcopy_parse_segdesc_02

Pull slave-dmaengine fixes from Vinod Koul:
 "Here is the slave dmanegine fixes.  We have the fix for deadlock issue
  on imx-dma by Michael and Josh's edma config fix along with author
  change"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: imx-dma: fix callback path in tasklet
  dmaengine: imx-dma: fix lockdep issue between irqhandler and tasklet
  dmaengine: imx-dma: fix slow path issue in prep_dma_cyclic
  dma/Kconfig: Make TI_EDMA select TI_PRIV_EDMA
  edma: Update author email address

Pull btrfs fixes from Chris Mason:
 "This is a small collection of fixes, including a regression fix from
  Liu Bo that solves rare crashes with compression on.

  I've merged my for-linus up to 3.12-rc3 because the top commit is only
  meant for 3.12.  The rest of the fixes are also available in my master
  branch on top of my last 3.11 based pull"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: Fix crash due to not allocating integrity data for a bioset
  Btrfs: fix a use-after-free bug in btrfs_dev_replace_finishing
  Btrfs: eliminate races in worker stopping code
  Btrfs: fix crash of compressed writes
  Btrfs: fix transid verify errors when recovering log tree

Pull GPIO fixes from Linus Walleij:
 "Two patches for the OMAP driver, dealing with setting up IRQs properly
  on the device tree boot path"

* tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio/omap: auto-setup a GPIO when used as an IRQ
  gpio/omap: maintain GPIO and IRQ usage separately

Pull USB fixes from Greg KH:
 "Here are none fixes for various USB driver problems.  The majority are
  gadget/musb fixes, but there are some new device ids in here as well"

* tag 'usb-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: chipidea: add Intel Clovertrail pci id
  usb: gadget: s3c-hsotg: fix can_write limit for non-periodic endpoints
  usb: gadget: f_fs: fix error handling
  usb: musb: dsps: do not bind to "musb-hdrc"
  USB: serial: option: Ignore card reader interface on Huawei E1750
  usb: musb: gadget: fix otg active status flag
  usb: phy: gpio-vbus: fix deferred probe from __init
  usb: gadget: pxa25x_udc: fix deferred probe from __init
  usb: musb: fix otg default state

Pull tty fixes from Greg KH:
 "Here are two tty driver fixes for 3.12-rc4.

  One fixes the reported regression in the n_tty code that a number of
  people found recently, and the other one fixes an issue with xen
  consoles that broke in 3.10"

* tag 'tty-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  xen/hvc: allow xenboot console to be used again
  tty: Fix pty master read() after slave closes

Pull staging fixes from Greg KH:
 "Here are 4 tiny staging and iio driver fixes for 3.12-rc4.  Nothing
  major, just some small fixes for reported issues"

* tag 'staging-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: comedi: ni_65xx: (bug fix) confine insn_bits to one subdevice
  iio:magnetometer: Bugfix magnetometer default output registers
  iio: Remove debugfs entries in iio_device_unregister()
  iio: amplifiers: ad8366: Remove regulator_put