CHV was forgotten the intel_{dp,hdmi}_prepare() were introduced (or the
chv patches were still in flight?). Call these when enabling the ports.

Things tend to work much better when we actually write something
to the port registers :)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Split chv_update_pll() into two parts ala:
 commit bdd4b6a6
 Author: Daniel Vetter <daniel.vetter@ffwll.ch>
 Date:   Thu Apr 24 23:55:11 2014 +0200

    drm/i915: Extract vlv_prepare_pll
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We enable the DPLL refclock already when bringing up the cmnlane power
well, so also leave it on when otherwise disabling the DPLL.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Punit seems a bit WIP still. Disable cdclk changes until we have
hardware where it works.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Looks like the Punit is supposed to support the 400MHz cdclk directly on
chv, so we don't need the vlv tricks.

FIXME: Punit doesn't seem ready for this yet on current hw
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since we started using intel_runtime_pm_disable_interrupts() at normal
(non-runtime) suspend/resume, we had to remove a WARN from
ironlake_disable_display_irq to avoid a case where we were doing the
correct thing and the WARN was not really needed. The problem is that
the WARN was useful in other cases, and its removal can hide some bugs
that we would catch automatically.

To be able to add back the WARN, we have to call intel_crtc_control()
before interrupts are disabled, which is what this patch currently
does.

Also notice that Ville's patch from the Watermarks series "drm/i915:
Leave interrupts enabled while disabling crtcs during suspend" also
did a change that's equivalent to the one we're doing on this patch,
with the exception that its original patch, when applied to the
current tree, procduces a WARN.

Related commits:

commit daa390e5ee45cc051d6bf37b296901f2f92b002d
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
    drm/i915: don't warn if IRQs are disabled when shutting down display IRQs

commit e11aa362
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
    drm/i915: use runtime irq suspend/resume in freeze/thaw

Note that the function part of this patch has already been done in

commit 0e32b39c
Author: Dave Airlie <airlied@redhat.com>
Date:   Fri May 2 14:02:48 2014 +1000

    drm/i915: add DP 1.2 MST support (v0.7)

with the fixup

commit 09b64267
Author: Dave Airlie <airlied@redhat.com>
Date:   Wed Jul 23 14:25:24 2014 +1000

    drm/i915: don't suspend gt until after we disable irqs and display (v2)

so all that's left from Paulo's patch is reinstating the WARNING.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Explain conflict resolution with Dave's DP MST patches with a
note in the commit message.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Turns out we were again way too naive and optimistic, of course things
will change.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is only going to get worse, so split it now to avoid adding more
cases to the if/else ladder.
Suggested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We'll need a different algorithm to select the shared DPLL.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since the run-time PM on DPMS series, this function has an outdated
comment. Refresh it a bit.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Future platform will use config->ddi_pll_sel in a different way.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So we can easily provide an alternate implementation in the future.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Future platform will slightly change that.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Not all those fields are valid on a given platform. Make it explicit.

Unions could also be used, but were cluttering some code paths with
if/else ladders.

v2: Don't use anonymous unions (Daniel)
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

CHV supports DP training pattern 3. Add the required stuff.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Split some WM debug prints to multiple lines. This shouldn't hurt
grappability since the important part is at the start and the rest
is just repeated stuff for each pipe.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

According to the specifications bit 6 is actually valid in the stride register.

Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NRafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add the TX wells for port D. The Punit subsystem numbers are a total
guess at this time. Also I'm not sure these even exist. Certainly the
Punit in current hardware doesn't deal with these.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add the TX wells for ports B and C just like on VLV.

Again Punit doesn't seem ready (or the wells don't even exist anymore)
so leave it iffed out.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

CHV has a power well for each pipe. Add the code to deal with them.

The Punit in current hardware doesn't seem ready for this yet, so
leave it iffed out.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Not sure if it's still there since chv has per-pipe power wells.
At least with current Punit this doesn't work. Also the display
irq handling would need to be adjusted for pipe C. So leave the
code iffed out for now.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Both VLV and CHV handle the cmnreset stuff in the power well code now,
so intel_reset_dpio() is no longer needed.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

CHV has two display PHYs so there are also two cmnlane power wells. Add
the approriate code to power the wells up/down.

Like on VLV we do the cmnreset assert/deassert and the DPLL refclock
enabling at approriate times.

This code actually works on my bsw.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add chv_power_wells[] so we can start to build up the power well support
for chv. Just the "always on" well there initialy.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: NRafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Share the waitqueue that drm_irq uses when performing the vblank evade
trick for atomic pipe updates.

v2: Keep intel_pipe_handle_vblank() (Chris)
Suggested-by: NDaniel Vetter <daniel@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add a small static inline helper to grab the vblank wait queue based on
the drm_crtc.

This is useful for drivers to do internal vblank waits using
wait_event() & co.

v2: Pimp commit message (Daniel)
    Add kernel doc (Daniel)
Suggested-by: NDaniel Vetter <daniel@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Adding relevant read out comparison code, in check_crtc_state, for the new
member of crtc_config, dp_m2_n2, which was introduced to store link_m_n
values for a DP downclock mode (if available). Suggested by Daniel.

v2: Changed patch title.
Daniel's review comments incorporated.
Added relevant state readout code for M2_N2. dp_m2_n2 comparison to be done
only when high RR is not in use (This is because alternate m_n register
programming will be done only when low RR is being used).

v3: Modified call to get_m2_n2 which had dp_m_n as param by mistake.
Compare dp_m_n and dp_m2_n2 for gen 7 and below. compare the structures
based on DRRS state for gen 8 and above.
Save and restore M2 N2 registers for gen 7 and below

v4: For Gen>=8, check M_N registers against dp_m_n and dp_m2_n2 as there is
only one set of M_N registers

v5: Removed the chunk which saves and restores M2_N2 registers. Modified
get_m_n() to get M2_N2 registers as well. Modified the macro which compares
hw.dp_m_n against sw.dp_m2_n2/sw.dp_m_n for gen > 8.

v6: Added check to compare dp_m2_n2 only when DRRS is enabled

v7: Modified drrs check to use has_drrs

v8: Add has_drrs check before reading M2_N2 registers
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For Gen < 8, set M2_N2 registers on every mode set. This is required to make
sure M2_N2 registers are set during boot, resume from sleep for cross-
checking the state. The register is set only if DRRS is supported.

v2: Patch rebased

v3: Daniel's review comments
	- Removed HAS_DRRS(dev) and added bool has_drrs to pipe_config to
	track drrs support

v4: Jesse's review comments
	- Made changes to set m2_n2 in intel_dp_set_m_n()
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This reverts commit 521e62e4.

Although POST_SYNC brought a bit of stability to Semaphores on BDW
it didn't solved all issues and some hungs can still occour when
semaphores are enabled on BDW. Also some sloweness can be found on some
igt tests, althoguth it apparently doesn't affect real workloads.

Besides that, no real performance gain was found on our tests with different
and even multiple workloads.

Let's disable it again for now. At least until we are sure it is safe
to re-enable it.
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Withtout this, ring initialization fails reliabily during resume with

	[drm:init_ring_common] *ERROR* render ring initialization failed ctl 0001f001 head ffffff8804 tail 00000000 start 000e4000

This is not a complete fix, but it is verified to make the ring
initialization failures during resume much less likely.

We were not able to root-cause this bug (likely HW-specific to Gen4 chips)
yet. This is therefore used as a ducttape before problem is fully
understood and proper fix created, so that people don't suffer from
completely unusable systems in the meantime.

The discussion and debugging is happening at

	https://bugs.freedesktop.org/show_bug.cgi?id=76554Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This particular nasty presented itself while trying to register the
intelfb device (intel_fbdev.c). During the process of registering the device
the driver will disable the crtc via i9xx_crtc_disable. These will
also disable the panel using the generic mipi panel functions in
dsi_mod_vbt_generic.c. The stale MIPI generic data sequence pointers would
cause a crash within those functions. However, all of this is happening
while console_lock is held from do_register_framebuffer inside fbcon.c. Which
means that you got kernel log and just the device appearing to reboot/hang for
no apparent reason.

The fault started from the FB_EVENT_FB_REGISTERED event using the
fb_notifier_call_chain call in fbcon.c.

This regression has been introduced in

commit d3b542fc
Author: Shobhit Kumar <shobhit.kumar@intel.com>
Date:   Mon Apr 14 11:00:34 2014 +0530

    drm/i915: Add parsing support for new MIPI blocks in VBT

Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: NRafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: NShobhit Kumar <shobhit.kumar@intel.com>
[danvet: Add regression citation.]
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We might be leaving the PGU Frequency (and thus vnn) high during the suspend.
Flusing the delayed work queue should take care of this.
Signed-off-by: NDeepak S <deepak.s@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

BDW has many other Display Engine interrupts and GT interrupts registers.
Collecting it properly on gpu_error_state.

On debugfs all was properly listed already but besides we were also listing old
DEIER and GTIER that doesn't exist on BDW anymore. This was causing
unclaimed register messages

v2: Fix small issues of first version and don't read DEIER regs when pipe's
    power well is disabled
v3: bikeshed accepted: use enum pipe pipe instead of int i for pipe interection
v4: Ben notice previous version was checking for display_power_enabled without
    using propper locks. Using _unlocked version isn't reliable and we cannot
    get this registers when power well is off. So let's avoid getting all DE_IER
    per pipe for now. If someone think this is an useful information it can be
    added later.
v5: Ben: put back debugfs stuff that might be coverred by pm_get and use
    	 gen >= 8 trying to predict future.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81701
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: N(v3) Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If the actual head has progressed forward inside a batch (request),
don't accumulate hangcheck score.

As the hangcheck score in increased only by acthd jumping backwards,
the result is that we only declare an active batch as stuck if it is
trapped inside a loop. Or that the looping will dominate the batch
progression so that it overcomes the bonus that forward progress gives.

v2: Improved commit message (Chris Wilson)
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
[danvet: s/active_loop/active (loop)/ as requested by Chris.]
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On Broadwell, any PIPE_CONTROL with the "State Cache Invalidate" bit set
must be preceded by a PIPE_CONTROL with the "CS Stall" bit set.

Documented on the BSpec 3D workarounds page.
Reviewed-by: NRafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: NKenneth Graunke <kenneth@whitecape.org>
[vsyrjala: add chv w/a note too]
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We'll want to reuse this for a workaround.
Signed-off-by: NKenneth Graunke <kenneth@whitecape.org>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Rmove now unused int.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The DDL registers can hold 7bit numbers. Make the most of those seven
bits by adjusting the threshold where we switch between the 64 vs. 32
precision multipliers.

Also we compute 'entries' to make the decision about precision, and then
we recompute the same value to calculate the actual drain latency. Just
use the already calculate 'entries' there.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>