The new ucode package format holds also the usniffer images
(in addition to the operational images and the TLVs).
The driver can load the usniffer image if debug
configuration tells it to.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Sometimes there is a need to configure some registers for
setting some FW properties, such as the FW monitor mode
(internal/external). This patch supports setting this for
PCIe mode.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Send all debug-configuration HCMDs that are set in the TLVs
to the FW. This may include HCMDs to configure the FW
monitor and FW log level, for example.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Interoperability issues were identified and root caused to
the Smart Fifo watermarks. These issues arose with
NetGear R7000. Fix this.

Cc: <stable@vger.kernel.org> [3.14+]
Fixes: 1f3b0ff8 ("iwlwifi: mvm: Add Smart FIFO support")
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Handle NVM file header. When NVM header detected, skip
the header and reading only the sections data.
Signed-off-by: NIdan Kahlon <idanx.kahlon@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add the channels on which there was a match for every match reported
by the firmware.  The firmware reports the channels as indices to the
array of channels that was passed in the scheduled scan request, so we
need to save the array when entering D3 to make sure it is available
when we resume.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add SSID information to the net-detect indication to userspace.  Fetch
the matched profiles from the firmware in order to find the correct
SSIDs in the profiles that matched.

Since the net-detect information is stored in cfg80211, and in theory
it could change while we are waking up and reading the matched
profiles, we need to save it when we enter D3 so it is available
during resume.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

IWL_MVM_REF_PROTECT_CSA is missing from the ref strings
used by debugfs.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This impacts the partition between BT and Wifi.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this TLV flag set.
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this TLV flag set.
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This TLV flag is set for all the supported firmwares.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This firmware is not supported anymore.
Stop loading this firmware - and remove the code that
handled older versions.
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Query the firmware for scan offload matches when waking up in order to
report net detect as the reason for the wake up.

This requires a new command API to be implemented.  Additionally,
remove some net detect command entries that are not valid anymore.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In case of channel switch, we need to teardown the TDLS peers.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The driver knows whether an rx frame was beamformed and marks
it in the radiotap VHT flags. However it should also declare
that it knows to extract this info otherwise this gets discarded
by sniffers like Wireshark.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add support to MFUART loading notification (print notification
data with IWL_DEBUG_INFO)
Signed-off-by: NChaya Rachel Ivgy <chaya.rachel.ivgi@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

call the appropriate iwl_trans_suspend/resume ops
on iwl_mvm_suspend/resume calls.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the device wakes up due to netdetect, we need to query different
things from the firmware than when it wakes up with a normal WoWLAN.
To make this easier, separate the netdetect wake up handling from the
rest.  For now, we don't send netdetect as a wake up reason, treating
it as a non-wireless wake up.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Refactor the iwl_mvm_query_wakeup_reasons() function to split the part
that gets the firmware status from the part that sets up the WoWLAN
status.  This will allow netdetect to reuse the code.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We need to send a WOWLAN_CONFIGURATION command also for netdetect and
configure the rfkill release trigger if needed.  To do so, refactor
the code that configures wowlan and netdetect when suspending and send
the WOWLAN_CONFIGURATION command also for net_detect.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add the net detect WoWLAN flag to indicate support and use the
nd_config from the WoWLAN configuration to start net detect, if it is
set.  The WoWLAN configuration takes precedence over the debugfs
configuration.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When another vif is also running during a channel switch, we need to
use a session protection when we move to the new channel, so that we
don't miss the beacons.  Without this, sometimes the other vif
repeatedly gets time exactly when we should be hearing the beacons,
preventing channel switch from completing.  Adding a session
protection that lasts from the moment the channel changes until 2
TBTTs later, ensures that we will hear the beacons on the destination
channel.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

If setting the CSA time event fails, we must clear the TE data,
otherwise we'll try to remove it when, for instance, a disconnection
occurs, causing a SYSASSERT.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

After a channel switch, transmission on the new channel is only
started once we see a beacon on it.  Thus, beacon filtering needs to
be disabled during channel switch so that mac80211 receives this
beacon and finishes the process.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

We need to call ieee80211_chswitch_done() ourselves just when the
absence TE started, so we perform the actual context switch early
enough.  To do so, add a dummy channel_switch op, which will cause
mac80211 to skip the countdown timer and allow us to call
ieee80211_chswitch_done() to complete the operation.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Now that mac80211 waits for the first beacon on the new channel before
calling post_channel_switch, the reconfiguration of the firmware
should be done in the post_channel_switch operation instead of when
assigning the vif to the new context.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Instead of using a hardcoded number of TUs before beacon 0 as the time
to start the absence and actual channel switch, calculate it in
relation to the beacon interval.  We use 10 TUs + beacon interval
before beacon 0 to target a bit before beacon 1.  This gives us enough
time to switch to the new channel before the AP/GO switches.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Add an absent time event when pre_channel_switch is called and use the
time event started indication to set the disable_tx bit instead of
doing it in unassign_vif().  This is done so that the firmware queues
are stopped before the actual switch takes place to avoid losing
packets while the AP/GO is performing its actual switch.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Now that all CSA flows are using the switch_vif_chanctx op, we can
rely on the switching_chanctx boolean that is passed to the
__iwl_mvm_assign_vif_chanctx() and __iwl_mvm_unassign_vif_chanctx()
functions to decide whether the context switch flows need to be
executed.  In this way we make the chanctx switch flow more generic,
without having to rely on the csa_active flag being set.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Disable PS when pre_channel_switch is called and add the
post_channel_switch operation to re-enable PS when the channel switch
is completed.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

The spec requires to decrement the CSA counters based on TBTT,
regardless if the beacon was actually transmitted. Previously, the fw
would send beacon notifications only for successfully transmitted
beacons. This behavior resulted in inaccurate CSA countdown. In order
to address this issue, the fw was changed to send beacon
notifications also for not transmitted beacons. Such notifications
have TX_STATUS_INTERNAL_ABORT (0x92).
Don't start the CSA countdown before first successfully transmitted
beacon, in order to guarantee that the CSA is announced for a
required period.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>

We have code to recover and go back to the original channel context if
something fails in the middle of switch_vif_chanctx, but we return the
error code of the recover calls instead of the original code, so if
the recovery succeeds, we will return 0 (success).  Fix this by not
assigning the return value of the recovery calls to ret.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Add support to reassign vif in switch_vif_chanctx.  This is similar to
the existing CHANCTX_SWMODE_SWAP_CONTEXTS mode, but doesn't delete the
old context nor creates a new one, doing to switch between two
existing contexts.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Currently we only support the CHANCTX_SWMODE_SWAP_CONTEXTS mode, but
we need to support other modes as well.  Spin a new function off in
order to make it easier to support other modes.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

We only need the csa_vif in AP/GO modes, and assigning for other
interfaces may cause problems, because csa_vif is never cleared.  To
prevent this, only assign the value if the iftype is
NL80211_IFTYPE_AP.  Use a switch to do this, even though, for now,
only the AP interface type is handled, because soon other interface
types will be added as well.

Additionally, convert the WARN() in the error case when a
channel-switch is already running to WARN_ONCE().
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

A new callback has been added to prepare the device for a channel
switch.  Use the new callback instead of the old channel_switch_beacon
operation.

This makes it possible to remove the channel_switch_beacon operation
from mac80211.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Maintain a TDLS channel-switch state and update it according to
notifications from FW and timeouts. Explicitly check all state
transitions are valid.
When switching is initiated by mac80211, use a delayed work to
periodically reschedule it from iwlwifi.
Give the FW mac80211 generated TDLS channel-switch request/response
templates. It will change appropriate values (switch timings) and Tx
them at appropriate times.

Enable the channel switch wiphy capability bit when the FW supports it.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Block TID 4 (VI) on a vif when using TDLS. This TID will be used by FW
for TDLS channel-switch requests and PTI requests.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>