- 16 3月, 2014 13 次提交
-
-
由 Tej Parkash 提交于
Issue: Pending IO wait does not complete after triggering Graceful reset, causing ack timeout and call traces. Fix: 1. Reducing the IO command wait timeout before triggering reset, as logically also timeout should be less than reset timeout (10sec). 2. Moving the abort IO after chip reset, because only after chip reset, driver owns the IO otherwise it is with firmware and can still revert back with response. Signed-off-by: NTej Parkash <tej.parkash@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Tej Parkash 提交于
Issue: While booting with kdump kernel, driver receive IOCB interrupts for which it is not ready which results in processing them before init_firmware during driver probe Fix: Two steps solution 1. Make driver ready to process the interrupt before interupts handlers is registered. 2. Stop driver processing iocb interrupts if not generated as per firmware protocol i.e R2H bit set Signed-off-by: NTej Parkash <tej.parkash@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Vikas Chaudhary 提交于
Issue: Mailbox command 0x102 (IDC Time Extend) failure seen while applying changes to iface using iscsiadm Fix: Added fix to extend IDC timeout only for ISP84xx when IDC ACK needs to be posted and disable ACB mailbox command completion is in intermediate state. Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Nilesh Javali 提交于
Issue: qla4xxx Unable to clear DDB indices when logout fails due to failure of connection close mbox command. Root cause: If login to session fail, iscsiadm make call to destroy_session. qla4xxx driver does not free ddb index map before free_ddb() Fix: Clear DDB Index map before free_ddb in "destroy_session" in case of connection close mailbox command failure with 4005h. Signed-off-by: NNilesh Javali <nilesh.javali@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Vikas Chaudhary 提交于
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Tej Parkash 提交于
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Vikas Chaudhary 提交于
If waiting for signals was interrupted then the device was put to FAILED state. Use msleep instead of msleep_interruptible to handle this correctly. Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Nilesh Javali 提交于
Signed-off-by: NNilesh Javali <nilesh.javali@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Nilesh Javali 提交于
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Vikas Chaudhary 提交于
Removed AF_83XX_NO_FWDUMP flag and directly checking IDC_CTRL bit1 while taking minidump, to check for graceful reset. Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Vikas Chaudhary 提交于
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Vikas Chaudhary 提交于
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Nilesh Javali 提交于
Issue: For ISP8xxx, adapter initialization is not retried if qla4xxx_initialize_adapter fails. Fix: If qla4xxx_initialize_adapter fails, first check if failure is due to IRQs not attached in order to skip retrial, then free the IRQs and then retry initializing the adapter. Signed-off-by: NNilesh Javali <nilesh.javali@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
- 07 1月, 2014 1 次提交
-
-
由 Masanari Iida 提交于
This patch fixed several typo in printk from various part of kernel source. Signed-off-by: NMasanari Iida <standby24x7@gmail.com> Signed-off-by: NJiri Kosina <jkosina@suse.cz>
-
- 20 12月, 2013 5 次提交
-
-
由 Vikas Chaudhary 提交于
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Adheer Chandravanshi 提交于
Recreate the chap data list during the get chap operation in qla4xxx_get_chap_list(). Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Adheer Chandravanshi 提交于
Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Lalit Chandivade 提交于
The statistics include MAC, TCP/IP & iSCSI statistics. Signed-off-by: NLalit Chandivade <lalit.chandivade@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Vikas Chaudhary 提交于
Added support for Diagnostics MBOX command via BSG Vendor HST_VENDOR interface. This command provides various tests for validating hardware functionality. Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
- 17 12月, 2013 3 次提交
-
-
由 Dan Carpenter 提交于
We should cap the size of memcpy() because it comes from the network and can't be trusted. Fixes: 26ffd7b4 ('[SCSI] qla4xxx: Add support to set CHAP entries') Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Acked-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Adheer Chandravanshi 提交于
Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Harish Zunjarrao 提交于
Added support to display and update additional network parameters through iscsiadm. Signed-off-by: NHarish Zunjarrao <harish.zunjarrao@qlogic.com> Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
- 25 10月, 2013 7 次提交
-
-
由 Adheer Chandravanshi 提交于
Add support to get local CHAP - index, username and password, sysfs params of iscsi session corresponding to flash target entry. Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Adheer Chandravanshi 提交于
Provide support to add/update the CHAP entries in adapter's flash using iscsi tools, like Open-iSCSI. Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Adheer Chandravanshi 提交于
To write a CHAP entry in adapter's flash calculate the offset based on the type of adapter. Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Adheer Chandravanshi 提交于
If any flash target entry is using CHAP authentication then set CHAP username and password sysfs params for the corresponding iscsi sessions. Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Adheer Chandravanshi 提交于
Support setting of CHAP_OUT_IDX param for the target entry in flash. Setting of valid local CHAP index with enable CHAP AUTH for that flash target entry and disabling CHAP AUTH will invalidate the CHAP index for the flash target entry. Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Adheer Chandravanshi 提交于
Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Manish Rangankar 提交于
Earlier logic for driver created iscsi_session->discovery_parent_idx was to store ram index of a sendtarget entry, but driver frees sendtarget ram index as soon as firmware is done with discovery, which is available for further use. So changing the logic to point iscsi_session->discovery_parent_idx to store sendtarget flashnode index. Signed-off-by: NManish Rangankar <manish.rangankar@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
- 14 10月, 2013 1 次提交
-
-
由 Jingoo Han 提交于
Since commit 0998d063 (device-core: Ensure drvdata = NULL when no driver is bound), the driver core clears the driver data to NULL after device_release or on probe failure. Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: NJingoo Han <jg1.han@samsung.com> Cc: James Bottomley <JBottomley@parallels.com> Signed-off-by: NJiri Kosina <jkosina@suse.cz>
-
- 03 9月, 2013 8 次提交
-
-
由 Vikas Chaudhary 提交于
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Vikas Chaudhary 提交于
Return error from function qla4_8xxx_collect_md_data() if minidump data collection fails. Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Santosh Vernekar 提交于
Signed-off-by: NSantosh Vernekar <santosh.vernekar@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Santosh Vernekar 提交于
Add pex-dma support for ISP8324 and ISP8042 to improve the minidump capture time. Signed-off-by: NSantosh Vernekar <santosh.vernekar@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Vikas Chaudhary 提交于
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Vikas Chaudhary 提交于
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Nilesh Javali 提交于
While loopback diagnostic is in progress, disable the ACB which resets all the active connections to target. Disable ACB would filter out all the DHCP multicast and broadcast packets which otherwise cause the diagnostic test to take longer time to complete or failures in some other cases. Signed-off-by: NNilesh Javali <nilesh.javali@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Vikas Chaudhary 提交于
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
- 24 8月, 2013 2 次提交
-
-
由 Adheer Chandravanshi 提交于
Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Adheer Chandravanshi 提交于
Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com> Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-