Add keypad data node in omap4 device tree file.
Also fill the device tree binding parameters
with the required value in "omap4-sdp" dts file.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
[b-cousson@ti.com: Re-align the entries and the comments]

DMIC IP is used to connect up to 6 digital microphones directly to OMAP.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

McPDM is used on OMAP4 based boards to communicate with an external audio
codec (twl6040).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add wdt node to support dt.
Signed-off-by: NXiao Jiang <jgq516@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add OMAP mmc related device tree data for OMAP4.
Currenly limited to only omap4-panda and omap4-sdp
boards.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add the 4 McSPI controller nodes present in an OMAP4 device.

Remove SPI static device initialisation if DT is populated.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: NRob Herring <rob.herring@calxeda.com>

Add the 6 GPIOs controller nodes present in OMAP4.

Remove gpio static device initialisation if DT is populated.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>

The GIC binding was updated in 3.2 and expects 3 interrupt-cells.
- Update the #interrupt-cells
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>

Add i2c controllers nodes into the main ocp bus.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

Follow the DTS convention and thus name the nodes <name>@<address> without
any '0x' prefix in the physical address.
Suggested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Pass minimal data needed for console boot, from dt, for
OMAP4 panda/sdp and OMAP3 beagle boards, and get rid of the
static initialization from generic board file.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Reviewed-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add nodes for devices used by PM code (mpu, dsp, iva).

Add a cpus node as well as recommended in the DT spec.

Remove mpu, dsp, iva devices init if is populated.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Kevin Hilman <khilman@ti.com>

Used the main OCP node to add bindings with the l3_noc driver.
Remove l3_noc static device creation if DT is populated.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>

Add initial device-tree support for OMAP4 SoC.

This is based on the original panda board patch done by Manju:
http://permalink.gmane.org/gmane.linux.ports.arm.omap/60393

Add the generic GIC interrupt-controller from ARM.

Add an empty "soc" node to contain non memory mapped IPs
(DSP, MPU, IPU...).

Note: Since reg, irq and dma are provided by hwmod for the
moment, these attributes will not be present at all in DTS
to highlight the gap. They will be added as soon as dma bindings
will be there and drivers will be adapted.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>