Add vendor specific command to change controller device speed.
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Fix for spaces prohibited around that '->' reported by checkpatch and space prohibited
between function name and open parenthesis '('
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch fixes the command length alignment issue for Intel Bluetooth
8260.

The length of parameters in the firmware downloading command must be
multiplication of 4. If not, the command must append Intel_NOP command
with extra parameters, zeros, at the end, and the firmware file is
already included Intel_NOP command for alignment.

This patch checks the next command and if the next command is Intel_NOP
command, it reads the Intel_NOP command and send them together.

For example, if the data from the firmware file looks like this:
8E FC 03 11 22 33 02 FC 03 00 00 00

Previously, btusb sends two commands:
09 FC 06 8E FC 03 11 22 33
09 FC 06 02 FC 03 00 00 00

This won't work because the length of parameters are 6 which violates
the 4 byte alignment.

This patch will append them together and send as one command:
09 FC 0C 8E FC 03 11 22 33 02 FC 03 00 00 00

Based on previous work from Tedd Ho-Jeong An <tedd.an@intel.com>
Reported-by: NTedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Tested-by: NTedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org

That patch corrects the typo in usb vendor id for Roper Class 1 Bluetooth
Dongle. Problem with typo is present since 4.0 kernel.

Content /sys/kernel/debug/usb/devices for these dongle:

T:  Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1310 ProdID=0001 Rev=15.00
S:  Manufacturer=SiW
S:  Product=SiW
S:  SerialNumber=E7BB050D0B00
C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr= 50mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NAleksei Volkov <info@dv2c.ru>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 4.0.x

The btusb_read_local_version function has only a single user and with
that just move its functionality in place where it belongs.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The __hci_cmd_sync function already handles the command status and
command complete errors. No need to check the status field again.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The SKB returned from the Intel specific version information command is
missing a kfree_skb.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org

BugLink: https://bugs.launchpad.net/bugs/1427680

This device requires new firmware files
 AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to
/lib/firmware/ar3k/ that are not included in linux-firmware yet.

T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3474 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

BugLink: https://bugs.launchpad.net/bugs/1462614

This device requires new firmware files
 AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to
/lib/firmware/ar3k/ that are not included in linux-firmware yet.

T: Bus=03 Lev=01 Prnt=01 Port=09 Cnt=06 Dev#= 7 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e076 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

Use btbcm helpers to perform controller setup.
Perform host UART reset to init speed between btbcm_patchram() and
btbcm_finalize(). This may be need because firmware loading may have
reseted controller UART to init speed.
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Firmware loading may reset the controller UART speed and needs to set
host UART speed back to init speed.

UART drivers setup is split in 3 parts:
- btbcm_initialize() resets the controller and returns the firmware
  name based on controller revision and sub_version.
- btbtcm_patchram() (already existing and public), which takes the
  firmware name as parameter, requests the firmware and loads it to
  the controller.
- btbcm_finalize() which resets the controller, reads local version
  and checks if the controller address is a default one or not.

Remove firmware name retrieval for UART controllers from
btbcm_setup_patchram().
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add initial and operational speeds.
Change to operational speed as soon as possible. If controller
set_baudrate() fails, continue at initial speed.
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add "waiting for configuration" address.
Add lmp_subver and firmware name for BCM4324B3 controller.
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Move request/release_firmware() out of btbcm_patchram().
This allows a better error management, if request_firmware() returns an
error then the controller will be used without firmware loading and 0 is
returned.
This will imply to change btbcm_patchram() to accept a firmware instead
of firmware name.
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Fix spaces required around that '=' reported by checkpatch.
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Realtek btusb devices don't currently work after suspend/resume because
the updated firmware is quietly lost - the USB hub doesn't notice any
status change upon resume, but some kind of reset has definitely
happened as the LMP subversion has reverted to its original value.

Set the reset_resume flag to trigger probe and upload the new firmware
again.

Like the vendor code, I assume this is not needed when the device is
selected as a wakeup source and hence will retain power during suspend.
On the 2 products I have to hand, when trying this configuration the
hardware seems unable to keep the device powered up during suspend.
The USB hub then detects a status change on resume and does a reset,
so we do not end up in broken state.
Signed-off-by: NDaniel Drake <drake@endlessm.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The variables txcrc and hciextn are bool type. So assigning true
instead of 1.
Signed-off-by: NShailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The reset is a bool type variable. So assigning true to reset instead
of 1.
Signed-off-by: NShailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The previous commit(3267c884) missed QCA61x4 ROME v2.0 info on Samsung
so its BT is not activated and the below message is shown.

[    8.009638] usb 1-1: New USB device found, idVendor=0cf3, idProduct=e300
[    8.012637] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    8.102901] Bluetooth: hci0: don't support firmware rome 0x200

This patch adds QCA61x4 ROME v2.0 info in qca_devices_table[], and is
verified on Samsung with the firmware provided by Kim, Ben Young Tae
<ytkim@qca.qualcomm.com>.

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e300 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NChan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Remove test of command reply status as it is already performed by
__hci_cmd_sync().

__hci_cmd_sync_ev() function already returns an error if it got a
non-zero status either through a Command Complete or a Command
Status event.

For both of these events the status is collected up in the event
handlers called by hci_event_packet() and then passed as the second
parameter to req_complete_skb(). The req_complete_skb() callback in
turn is hci_req_sync_complete() for __hci_cmd_sync_ev() which stores
the status in hdev->req_result. The hdev->req_result is then further
converted through bt_to_errno() back in __hci_cmd_sync_ev().
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Remove test of command reply status as it is already performed by
__hci_cmd_sync().

__hci_cmd_sync_ev() function already returns an error if it got a
non-zero status either through a Command Complete or a Command
Status event.

For both of these events the status is collected up in the event
handlers called by hci_event_packet() and then passed as the second
parameter to req_complete_skb(). The req_complete_skb() callback in
turn is hci_req_sync_complete() for __hci_cmd_sync_ev() which stores
the status in hdev->req_result. The hdev->req_result is then further
converted through bt_to_errno() back in __hci_cmd_sync_ev().
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Remove test of command reply status as it is already performed by
__hci_cmd_sync().

__hci_cmd_sync_ev() function already returns an error if it got a
non-zero status either through a Command Complete or a Command
Status event.

For both of these events the status is collected up in the event
handlers called by hci_event_packet() and then passed as the second
parameter to req_complete_skb(). The req_complete_skb() callback in
turn is hci_req_sync_complete() for __hci_cmd_sync_ev() which stores
the status in hdev->req_result. The hdev->req_result is then further
converted through bt_to_errno() back in __hci_cmd_sync_ev().
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

As already done for btintel and btbcm export setup as separate function
in a vendor-specific module to hold all the Realtek specific commands.
Signed-off-by: NCarlo Caione <carlo@endlessm.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch fixes a compile warnning "dump_num maybe used uninitialized in
this function".
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

BugLink: https://bugs.launchpad.net/bugs/1449730

T:  Bus=01 Lev=01 Prnt=01 Port=04 Cnt=02 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=300f Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Remove the DEBUG define as the debug code; so can remove mass debug info
from log buffer when using dmesg.
Signed-off-by: NLeo Yan <leo.yan@linaro.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Device 0cf3:e007 is one of the QCA ROME family.

T:  Bus=01 Lev=01 Prnt=01 Port=05 Cnt=02 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e007 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NWen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Device info in /sys/kernel/debug/usb/devices:

T:  Bus=01 Lev=01 Prnt=01 Port=05 Cnt=02 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e006 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NWen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The ">" should be ">=" so that we don't read past the end of the array.

Fixes: 9d9a113e3695 ('Bluetooth: btusb: Add Realtek 8723A/8723B/8761A/8821A support')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NDaniel Drake <drake@endlessm.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

ERROR: spaces required around that '<' (ctx:WxV)
+		if (err <0)
 		        ^

ERROR: code indent should use tabs where possible
+^I^I^I^I        sizeof(ver));$
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Realtek ship a variety of bluetooth USB devices that identify
themselves with standard USB Bluetooth device class values, but
require a special driver to actually work. Without that driver,
you never get any scan results.

More recently however, Realtek appear to have wisened up and simply
posted a firmware update that makes these devices comply with
normal btusb protocols. The firmware needs to be uploaded on each boot.

Based on Realtek code from https://github.com/lwfinger/rtl8723au_bt
('new' branch).

This enables bluetooth support in the Gigabyte Brix GB-BXBT-2807 which
has this RTL8723BE USB device:

T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 2.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3410 Rev= 2.00
S:  Manufacturer=Realtek
S:  Product=Bluetooth Radio
S:  SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms

There is no change to the USB descriptor after firmware update,
however the version read by HCI_OP_READ_LOCAL_VERSION changes from
0x8723 to 0x3083.

This has also been tested on RTL8723AE and RTL8821AE. Support for
RTL8761A has also been added, but that is untested.
Signed-off-by: NDaniel Drake <drake@endlessm.com>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Atheros support for missing the support for configuration of the
Bluetooth public address. Add support for the vendor specific command.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The driver callbacks in the Atheros support were all in a random order
and did not help readability of this driver. So reorder them to make
them aligned with what other Bluetooth UART drivers do. This patch is
not changing any actual code.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This isolates the Broadcom patchram download procedure as separate
function so that it can be easily used from USB and UART based drivers.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

I think the comments are used to debug, and we don't need them in
mainline code
Signed-off-by: NDingXiang <dingxiang@huawei.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Intel vendors events indicating firmware loading result and the
bootup of the operational firmware are currently hardcoded byte
comparisons. So intead of doing that, provide proper data structures
and actually use them.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Bluetooth address setting for Intel devices is provided by a generic
module now. Start using that module instead of relying it being included
in the driver.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Since the Intel Bluetooth support has its own header, it makes sense
to move all command structs into it.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Bluetooth address handling for Intel devices is provided by a generic
module now. Start using that module instead of relying it being included
in the driver.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The majority of Intel Bluetooth vendor commands are shared between USB
and UART transports. This creates a separate module that eventually
will hold all Intel specific commands, but for now just start with the
commands to change the Bluetooth public address and check for the
default address.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>