Add support for the AR3012 chip found on Fioxconn.

    usb-devices shows:

    T:  Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 44 Spd=12   MxCh= 0
    D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
    P:  Vendor=0489 ProdID=e057 Rev= 0.02
    C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
    I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
    E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
    E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
    I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
    E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
    I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
    E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
    I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
    E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
    I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
    E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
    I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
    E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
    I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
    E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NPeng Chen <pengchen@qca.qualcomm.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Patch adds support for BCM20702A0 device id (0a5c:21f4).

usb-devices after patch was applied:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21f4 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=E4D53DF154D6
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

usb-devices before patch was applied:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21f4 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=E4D53DF154D6
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NManoj Iyer <manoj.iyer@canonical.com>
Tested-by: NChris Gagnon <chris.gagnon@canonical.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Add support for the AR3012 chip found on the Toshiba Sallite M840-1000-XQ.

usb-devices shows:

T:  Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0930 ProdID=0219 Rev=00.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NGiancarlo Formicuccia <giancarlo.formicuccia@gmail.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Acer used this chip connected via USB:

Bus 005 Device 005: ID 0cf3:3005 Atheros Communications, Inc. AR3011 Bluetooth
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass          224 Wireless
  bDeviceSubClass         1 Radio Frequency
  bDeviceProtocol         1 Bluetooth
  bMaxPacketSize0        64
  idVendor           0x0cf3 Atheros Communications, Inc.
  idProduct          0x3005 AR3011 Bluetooth
  bcdDevice            0.01
  iManufacturer           0
  iProduct                0
  iSerial                 0
  bNumConfigurations      1
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Most of the include were unnecessary or already included by some other
header.
Replace module.h by export.h where possible.
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

HCI_QUIRK_NO_RESET name is misleading - purpose of this quirk is to
reset device on close instead of init, not to not reset at all.
Rename it to HCI_QUIRK_RESET_ON_CLOSE to avoid confusion.
Signed-off-by: NSzymon Janc <szymon.janc@tieto.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Hub-initiated LPM is not good for USB communications devices.  Comms
devices should be able to tell when their link can go into a lower power
state, because they know when an incoming transmission is finished.
Ideally, these devices would slam their links into a lower power state,
using the device-initiated LPM, after finishing the last packet of their
data transfer.

If we enable the idle timeouts for the parent hubs to enable
hub-initiated LPM, we will get a lot of useless LPM packets on the bus
as the devices reject LPM transitions when they're in the middle of
receiving data.  Worse, some devices might blindly accept the
hub-initiated LPM and power down their radios while they're in the
middle of receiving a transmission.

The Intel Windows folks are disabling hub-initiated LPM for all USB
communications devices under a xHCI USB 3.0 host.  In order to keep
the Linux behavior as close as possible to Windows, we need to do the
same in Linux.

Set the disable_hub_initiated_lpm flag for for all USB communications
drivers.  I know there aren't currently any USB 3.0 devices that
implement these class specifications, but we should be ready if they do.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Add Foxconn/Hon Hai AR5BBU22 Bluetooth Module( 0x489:0xE03C) to
the blacklist of btusb module and add it to the ath3k module to properly
load the firmware in Kernel 3.3.4
The device is integrated in  e.g. some  Acer Aspire 7750G.

Output from /sys/kernel/debug/usb/devices:

T:  Bus=01 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#=  6 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e03c Rev= 0.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NMichael Gruetzner <mgruetzn@gmx.de>
Signed-off-by: NGustavo Padovan <gustavo@padovan.org>

The alternate setting must be dynamically set according to the number of
active SCO links, and the bit depth of the audio. The possible values
for the alternate setting are described in the Bluetooth Core
Specification, Volume 4, Part B, section 2.1.1.
Signed-off-by: NMikel Astiz <mikel.astiz.oss@gmail.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo@padovan.org>

This change adds 0x0489:0xe033 to the btusb module.

This bluetooth usb device is integrated in the Acer TimelineX AS4830TG-6808 notebook.

Output from /sys/kernel/debug/usb/devices:

T:  Bus=01 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e033 Rev= 2.29
S:  Manufacturer=Broadcom Corp
S:  Product=Acer Module
S:  SerialNumber=60D819F74101
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  32 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  32 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NSteven Harms <sjharms@gmail.com>
Signed-off-by: NGustavo Padovan <gustavo@padovan.org>

Add another vendor specific ID for Atheros AR3012

output of usb-devices:
T:  Bus=02 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e004 Rev=00.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

BugLink: https://bugs.launchpad.net/bugs/922715Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add another vendor specific ID for Atheros AR3012 device.
This chip is wrapped by IMC Networks.

output of usb-devices:
T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3362 Rev=00.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

T: Bus=02 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e042 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=E4D53DCA61B5
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Reported-by: NDennis Chua <dennis.chua@canonical.com>
Signed-off-by: NManoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

I was trying to backport the following commit to RHEL-6

    From 0cea73465cd22373c5cd43a3edd25fbd4bb532ef Mon Sep 17 00:00:00 2001
    From: Oliver Neukum <oliver@neukum.org>
    Date: Wed, 21 Sep 2011 11:37:15 +0200
    Subject: [PATCH] btusb: add device entry for Broadcom SoftSailing

and noticed it wasn't working on an HP Elitebook.  Looking into the patch I
noticed a very subtle typo in the ids.  The patch has '0x05ac' instead of
'0x0a5c'.  A snippet of the lsusb -v output also shows this:

Bus 002 Device 003: ID 0a5c:21e1 Broadcom Corp.
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass          255 Vendor Specific Class
  bDeviceSubClass         1
  bDeviceProtocol         1
  bMaxPacketSize0        64
  idVendor           0x0a5c Broadcom Corp.
  idProduct          0x21e1
  bcdDevice            1.12
  iManufacturer           1 Broadcom Corp
  iProduct                2 BCM20702A0
  iSerial                 3 60D819F0338C
  bNumConfigurations      1

Looking at other Broadcom ids, the fix matches them whereas the original patch
matches Apple's ids.

Tested on an HP Elitebook 8760w.  The btusb binds and the userspace stuff loads
correctly.

Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: NDon Zickus <dzickus@redhat.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Add another vendor specific ID for Atheros AR3012 device.
This chip is wrapped by Lite-On Technology Corp.

output of usb-devices:
T:  Bus=04 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3005 Rev=00.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NGustavo Padovan <gustavo@padovan.org>

Add Atheros maryann 0cf3:311d PIDVID support
This module is AR3012 Series.

Include /sys/kernel/debug/usb/devices output here for reference

before:
T:  Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=311d Rev= 0.01
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

after:
T:  Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=311d Rev= 0.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NCho, Yu-Chen <acho@suse.com>
cked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

One more vendor-specific ID for BCM20702A0.

T:  Bus=01 Lev=03 Prnt=05 Port=02 Cnt=01 Dev#=  9 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0a5c ProdID=21e8 Rev=01.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=00027221F4E2
C:  #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NJoão Paulo Rechi Vita <jprvita@openbossa.org>
Acked-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The bluetooth module in the Asus UX31/UX21 is based on Atheros AR3012
and requires a firmware to be uploaded before it's usable.

output of usb-devices for this module:
T:  Bus=01 Lev=02 Prnt=02 Port=07 Cnt=03 Dev#=  6 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3375 Rev=00.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NEran <eran@over-here.org>
Tested-by: NMichal Labedzki <michal.labedzki@tieto.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Add another vendor specific ID for BCM20702A0.  This has been tested and
works on hardware with this device.

output of usb-devices:
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=04 Dev#= 6 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21e6 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=D0DF9AFB227B
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NJames M. Leddy <james.leddy@canonical.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The ID is found on Asus K54HR and K53U.
Blacklist the AR3011-based device ID [0489:e03d]
and add to ath3k.c for firmware loading.

Below is the output of usb-devices script:

Before the fiwmware loading:

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e03d Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

After the fiwmware loading:

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=3005 Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NKeng-Yu Lin <kengyu@canonical.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21f3 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=74DE2B344A7B
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NManoj Iyer <manoj.iyer@canonical.com>
Tested-by: NDennis Chua <dennis.chua@canonical.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

[ 2096.384084] btusb_send_frame:684: hci0
[ 2096.384087] usb 3-1: BOGUS urb flags, 2 --> 0
[ 2096.384091] Bluetooth: hci0 urb ffff8801b61d3a80 submission failed (22)

According the documentation in usb_submit_urb() URB_ISO_ASAP
flag is only allowed for endpoints of type USB_ENDPOINT_XFER_ISOC.

This reverts commit b8aabfc9.
Signed-off-by: NDaniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Recently we changed the way how we release driver-data. A driver is now
responsible of destroying the data so we no longer need the device lock
on deinitialization in btusb driver.
Signed-off-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The linux device model provides dev_set/get_drvdata so we can use this
to save private driver data.
This also removes several unnecessary casts.
Signed-off-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21f3 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=74DE2B344A7B
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NManoj Iyer <manoj.iyer@canonical.com>
Tested-by: NDennis Chua <dennis.chua@canonical.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Since we remove the owner field of hci_dev hci_dev_put and __hci_dev_put
do the same so we can merge them into one function. Same for
hci_dev_hold and __hci_dev_hold.
Signed-off-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

After unregistering an hci_dev object a bluetooth driver does not have
any callbacks in the hci_dev structure left over. Therefore, there is no
need to keep a reference to the module.

Previously, we needed this to protect the hci-destruct callback.
However, this callback is no longer available so we do not need this
owner field, anymore.  Drivers now call hci_unregister_dev() and they
are done with the object.
Signed-off-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Instead of using the hci-destruct callback we free our private driver
data on USB shutdown. We already called hci_unregister_dev() here so the
hci core will never ever call our callbacks again except the destruct
callback.

However, there is no reason to keep our *private* driver data alive if
we get never called again and the hci-core does never touch it the data.
So we simply free it right away and set the destruct callback to NULL.
Signed-off-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

[ 2096.384084] btusb_send_frame:684: hci0
[ 2096.384087] usb 3-1: BOGUS urb flags, 2 --> 0
[ 2096.384091] Bluetooth: hci0 urb ffff8801b61d3a80 submission failed (22)

According the documentation in usb_submit_urb() URB_ISO_ASAP
flag is only allowed for endpoints of type USB_ENDPOINT_XFER_ISOC.

This reverts commit b8aabfc9.
Signed-off-by: NDaniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

module_param(bool) used to counter-intuitively take an int.  In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.

It's time to remove the int/unsigned int option.  For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Add another vendor specific ID for BCM20702A0.

output of usb-devices:
T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21e3 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=9439E5CBF66C
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NWen-chien Jesse Sung <jesse.sung@canonical.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

For high-speed/super-speed isochronous endpoints, the bInterval
value is used as exponent, 2^(bInterval-1). Luckily we have
usb_fill_int_urb() function that handles it correctly. So we just
call this function to fill in the RX URB.

Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch fixes the following memory leak reported by kmemleak:

unreferenced object 0xffff880060a53840 (size 192):
  comm "softirq", pid 0, jiffies 4320571771 (age 1406.569s)
  hex dump (first 32 bytes):
    01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff81138a1c>] create_object+0x187/0x28b
    [<ffffffff814be12e>] kmemleak_alloc+0x73/0x98
    [<ffffffff811289d3>] __kmalloc+0xfc/0x123
    [<ffffffff81386546>] usb_alloc_urb+0x1e/0x48
    [<ffffffffa0130274>] btusb_send_frame+0x86/0x385 [btusb]
    [<ffffffffa02d8230>] hci_send_frame+0xa0/0xa5 [bluetooth]
    [<ffffffffa02d8a4e>] hci_cmd_task+0xa0/0xfb [bluetooth]
    [<ffffffff81058548>] tasklet_action+0x8f/0xef
    [<ffffffff81058a4c>] __do_softirq+0xf4/0x1db
    [<ffffffff81058bb7>] run_ksoftirqd+0x84/0x129
    [<ffffffff8106f1c4>] kthread+0xa0/0xa8
    [<ffffffff814dd144>] kernel_thread_helper+0x4/0x10
    [<ffffffffffffffff>] 0xffffffffffffffff

The problem is that when inc_tx() returns non-zero, we forgot
to call usb_free_urb().

Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: "Gustavo F. Padovan" <padovan@profusion.mobi>
Signed-off-by: NWANG Cong <amwang@redhat.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This converts the drivers in drivers/bluetooth/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.

Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.

Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: "Gustavo F. Padovan" <padovan@profusion.mobi>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since this device declares itself as vendor specific, must add
a new entry to device ID table to support it.

usb-device output of this device:

T:  Bus=01 Lev=02 Prnt=02 Port=03 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=413c ProdID=8197 Rev=01.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=D0DF9AA9C9F1
C:  #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NWen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

There are still three calls of usb_submit_urb() that will print errors
if those calls return -EPERM or -ENODEV. I have never triggered these,
so I'm not sure when these return values might be seen. It still makes
sense to be silent if these occur (since "urb is being killed" and
"device got disconnected" aren't things to worry about).
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

usb_submit_urb() returns -ENODEV when a usb device is disconnected. In
commit 4935f1c1 ("Bluetooth: btusb: be
quiet on device disconnect") I stopped treating that return as an error
in the three btusb_*_complete() functions.

It turns out btusb_send_frame() generates a similar error if the system
is suspended while the bluetooth usb device is enabled. The sensible
thing to do here seems to be to treat -ENODEV (and -EPERM) just like the
btusb_*_complete() functions now do.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

From 0cea73465cd22373c5cd43a3edd25fbd4bb532ef Mon Sep 17 00:00:00 2001
From: Oliver Neukum <oliver@neukum.org>
Date: Wed, 21 Sep 2011 11:37:15 +0200
Subject: [PATCH] btusb: add device entry for Broadcom SoftSailing

This device declares itself to be vendor specific
It therefore needs to be added to the device table
to make btusb bind.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Removed tests which prevent transmission of ACL packets
when the device is in HCI_RAW mode. These tests verified that
there are ACL or LE links currently tracked by the HCI
connection manager. However, a HCI_RAW mode device does not
use the connection manager. In these circumstances, the connection
counts will be zero, and thus, transmitted ACL packets dropped.

The acl_num test is actually a vestige of a previous bulk URB
scheme that is no longer used by this driver (bulk URBs were not
started until at least one ACL connection was created). This was
incompatible with some endpoint implementations and was dropped -
see commit 43c2e57f.

The utility of these tests is marginal - currently, the hci tx
scheduler cannot send an ACL or LE packet for an untracked connection
(except if the device is in HCI_RAW mode).

Lastly, no other transport layer driver enforces these same tests.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Acked-by: NAcked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>