This patch fixes checkpatch warnings about blank lines after an open brace '{'.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes multiple blank lines in the driver as per checkpatch
warnings.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes checkpatch warnings in be2net by adding a blank line
between declaration and code blocks.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a sparse warning about missing static declaration that was
introduced by the following commit:

fixes: 93676703 ("be2net: send a max of 8 EQs to be_cmd_modify_eqd() on Lancer")
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MODIFY_EQ_DELAY FW cmd on Lancer is supported for a max of 8 EQs per cmd.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report the ethtool port-type/supported/advertising values based on the
cable_type for QSFP and SFP+ interfaces. The cable_type is parsed from
the transceiver data fetched from the FW.
Signed-off-by: NRavikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: NSuresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the dump-module-eeprom and module-info
ethtool options.
Signed-off-by: NMark Leonard <mark.leonard@emulex.com>
Signed-off-by: NSuresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some configurations the FW doesn't allow changing flow control settings
of a link. Unless a v1 version of the SET_FLOW_CONTROL cmd is used, the FW
doesn't report an error to the driver.
Signed-off-by: NSuresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace strcpy with strlcpy, as it avoids a possible buffer overflow.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the following minor issues with log messages in be2net:
  1) Period is not required at the end of log message.
  2) Remove "Unknown grp5 event" logs to reduce noise. The driver can safely
     ignore async events from FW it's not interested in.
  3) Reword a log message for better readability to say that SRIOV
     "is disabled" rather than "not supported".
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are a few failure cases in be_cmd_get_regs() that ideally must return
an error value. This style is used across all the routines in be_cmds.c with
this routine being an exception. This patch fixes this.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the following log messages to help debugging
failure cases:
1) log FW version number: this is useful when driver initialization
fails and the FW version number cannot be queried via ethtool
2) per function resource limits for BEx chips: these values are
currently being printed only for Skyhawk and Lancer
3) PCI BAR mapping failure
4) function_mode/caps queried from FW: this helps catch any FW bugs
that could advertise wrong capabilities to the driver
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support to delete an existing FW-dump in Lancer via ethtool.
Initiating a new dump is not allowed if a FW dump is already present in the
adapter. The existing dump has to be first explicitly deleted.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A pointer to adapter struct is passed anyway to all of the FW-cmd routines
in be_cmds.c. For routines which query data from FW, the adapter pointer
is enough to return the queried fields.
There is no need to separately pass pointers to individual members of
the adapter structure. This patch fixes this for be_cmd_get_fw_ver()
and be_cmd_get_fw_cfg() routines.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the FW stops responding with completions, return -ETIMEDOUT error
(instead of -1) to the stack.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If SR-IOV is enabled in the adapter, the FW distributes queue resources
evenly across the PF and it's VFs. If the user is not interested in enabling
VFs, the queues set aside for VFs are wasted.
This patch adds support for the PF driver to re-configure the resource
distribution in FW based on the number of VFs enabled by the user.
This also allows for supporting RSS queues on VFs, when less number of VFs
are enabled per PF. When maximum number of VFs are enabled, each VF typically
gets only one RXQ.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PF driver must query the FW for VF's interface capabilities
to know if the VF is RSS capable or not.
This patch is in preparation for enabling RSS on VFs on Skyhawk-R.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix be_cmd_get_profile_cmd() to use be_cmd_notify_wait() routine,
which uses MBOX if MCCQ has not been created. Doing this reduces
code duplication; we don't need the _mbox/_mccq() variants anymore.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MCC async event processing code has 2 issues:
a) because of long struct names the code indentation is badly broken
b) description and definitions of how an MCC completion is interpreted as
   an async event are confusing (for e.g. the last word of an MCC event is
   named "code", while "code" is just a sub-field of the last word.)

This patch fixes the structure definitions, comments and re-factors code
as needed.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For some FW cmds, the caller just issues the cmd and doesn't wait for a
response. The response handling is done in the MCCQ compl processing context
only. Move this code into a separate routine to make be_mcc_compl_process()
more manageable.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch improves MCCQ error status handling in the following ways:
a) A MCC cmd completion returns a base-status and an addl-status.
So far, the routine be_mcc_compl_process() returned only the "status" value.
Now, embedd both statuses in the return value and let the caller routine access
the value of interest using base_status() and addl_status() macros.

b) Rename variables accordingly (base/addl) to avoid confusion while error
checking.

b) Some of the errors returned by FW are harmless and so an error msg is not
logged for such errors. Capture this logic in a separate routine to make the
code more readable.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Certain new flash regions have been added to Skyhawk-R FW image. The newer
FW images specify op_types for each region. A region is flashed only
when it's CRC doesn't match that of the region on the HW flash. While
upgrading to a new FW image the driver is expected to tolerate certain
errors.

This patch re-factors code under be_flash() to support the above scheme.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Skyhawk-R FW supports TX-rate setting only as a % value of the link
speed, set via the SET_PROFILE_CONFIG cmd.

This patch makes the necessary changes to the FW cmd descriptors to support
the above change and also introduces checks in be_set_vf_tx_rate() to allow
only discrete values (that map to % of the link-speed).
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <ben@decadent.org.uk>

be_cmd_rss_config() is called after the MCCQ is created; so this cmd is
now modified to use the MCCQ instead of MBOX. Also fixed some indentation
problem in this routine.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For putting interface into vlan promiscuous mode, we use be_cmd_rx_filter()
and not be_cmd_vlan_config(). So remove the "promiscuous" argument from
be_cmd_vlan_config().
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a funtion definition or a function call spans more than one
line, ensure that the first argument on the subsequent lines is
aligned to the first column after the opening paranthesis of the
function call.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This be2net patch implements the get/set_rxfh() ethtool hooks.
RSS_CONFIG device command is invoked to set hashkey and indirection table.
It also uses an initial random value for RSS hash key instead of a
hard-coded value as hard-coded values for a hash-key are usually
considered a security risk.
Signed-off-by: NVenkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the FW cmds needed for VxLAN offloads
on Skyhawk-R:
1) The VxLAN UDP port needs to be configured via the port-desc of
   SET_PROFILE_CONFIG_v1 cmd.
   This patch re-factors the be_set_profile_config() code (used so far
   only for setting VF QoS) to be used to set any type of descriptor.
2) The MANAGE_IFACE_FILTERS cmds is needed to convert a normal interface
   into a tunnel interface. This allows for RSS to work even on the inner
   TCP/UDP headers of VxLAN traffic.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRavikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to control VF's link state by implementing the
ndo_set_vf_link_state() hook.
Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently multi-channel configuration is read via the QUERY_FW_CONFIG cmd.
This method has been deprecated by the Skyhawk-R FW. Instead,
GET_PROFILE_CONFIG::port-desc must be used to query this configuration.

This patch also:
a) introduces a few macros to identify certain categories of multi-channel
configs
2) re-factors the be_cmd_set_profile_config() code to be able to read any kind
of desc (and not just the nic-desc.)
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch cleans-up wake-on-lan code in the following ways:
1) Removes some driver hacks in be_cmd_get_acpi_wol_cap() that were based
on incorrect assumptions.
2) Uses the adapter->wol_en and wol_cap variables for checking if WoL
is supported and enabled on an interface instead of referring to the
exclusion list via the macro be_is_wol_supported()
Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The use of NTKW_MAC_QUERY cmd has been deprecated for Skyhawk-R.
Replace the last remaining usage in be_vfs_mac_query() routine.
Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An earlier commit (f25b119c "Fix error messages while driver load for VFs")
incorrectly set the adapter->cmd_privileges value for VFs (in a
multi-channel config) to MAX_PRIVILEGES. This causes FW cmd failures
and avoidable error logs when certian cmds are issued by a VF.
Also, move the multi-channel hack to be_cmds.c inside
be_cmd_get_fn_privileges() routine.

Fixes: f25b119c "Fix error messages while driver load for VFs"
Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Skyhawk-R FW does not support SET/GET_EXT_FAT_CAPABILITIES cmds via which
FW logging level can be controlled. Also, the hack used in BE3 to control
FW logging level via the ethtool interface is not needed in Skyhawk-R.

This patch also cleans up this code by moving be_set/get_fw_log_level()
routines to be_cmds.c where they belong.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>

remove new line
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the GET_HSW_CONFIG cmd, the "pport" field must be set only while
querying the switch mode.  When the "pport" field is set, the
"interface_id" field must be set to the port number, otherwise, it
must be set to adapter->if_handle.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently this cmd is used only for Lancer.
MCC_CREATE_EXT_V1 supports larger CQ-ids and additional event codes for the
async_event_bitmap field.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>