This patch fixes an issue with transmit routine, which causes
"can_put_echo_skb: BUG! echo_skb is occupied!" message when
using "cansequence -p" on D_CAN controller.

In c_can driver, while transmitting packets tx_echo flag holds
the no of can frames put for transmission into the hardware.

As the comment above c_can_do_tx() indicates, if we find any packet
which is not transmitted then we should stop looking for more.
In the current implementation this is not taken care of causing the
said message.

Also, fix the condition used to find if the packet is transmitted
or not. Current code skips the first tx message object and ends up
checking one extra invalid object.

While at it, fix the comment on top of c_can_do_tx() to use the
terminology "packet" instead of "package" since it is more
standard.

Cc: stable@kernel.org # 2.6.39+
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

skb_defer_rx_timestamp was called with a freshly allocated skb but must
be called with rskb instead.
Signed-off-by: NStephan Gatzka <stephan@gatzka.org>
Cc: stable <stable@vger.kernel.org>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add .status callback that detects link state changes.
Tested with MCS7832CV-AA chip (9710:7830, identified as rev.C by the driver).
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=28532Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead
of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY
register greater than the maximum allowed by the latter macro, and fix a
typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan.

Also for clarity, rename a few defines as bit definitions instead of masks.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is another fixup where the data is not transfered into buffer
addressed by skb->data but into a page.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

when register_netdev fails, the init'ed NAPIs by netif_napi_add must be
deleted with netif_napi_del, and also when driver unloads, it should
delete the NAPI before unregistering netdevice using unregister_netdev.
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, we terminate the eeprom access through clearing the CS by:

RTL_W8 (Cfg9346, ~EE_CS); or writeb (~EE_CS, ee_addr);

This would left the eeprom into "Config. Register Write Enable:"
state which is not expcted as the highest two bits were set to
0x11 ( expected is the "Normal" mode (0x00)). Solving this by write
0x0 instead of ~EE_CS when terminating the eeprom access.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, we enable the receiver before setting the ring address which could
lead the card DMA into unexpected areas. Solving this by set the ring address
before enabling the receiver.

btw. I find and test this in qemu as I didn't have a 8139cp card in hand. please
review it carefully.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "!mlx4_is_slave" is totally confusing.  Fix with
constant MLX4_CMD_NATIVE, which is the intended behavior.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The range check was performed after using the port number.

Reverse this to prevent a potential array overflow.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- pass the following parameters:
  - firmware version (added QUERY_FW paravirtualization for that)

  - disable Blueflame on slaves. KVM disables write combining on guests,
    and we get better performance without BF in this case. (This requires
    QUERY_DEV_CAP paravirtualization, also in this commit)

  - max qp rdma as destination

- get rid of a chunk of "if (0)" dead code
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Port is used as an array index before we know if that is proper.

For example, in the catas event case, port is zero; however,
the port index should lie in the range (1..2).

Fix this by using 'port' only in the events where it is of interest.

Test for port out of range in the default (unhandled event) case,
and do not output a message if it is not an ethernet port.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In SRIOV mode, the number of EQs used when computing the total ICM size
was incorrect.

To fix this, we do the following:
1. We add a new structure to mlx4_dev, mlx4_phys_caps, to contain physical HCA
   capabilities.  The PPF uses the phys capabilities when it computes things
   like ICM size.

   The dev_caps structure will then contain the paravirtualized values, making
   bookkeeping much easier in SRIOV mode. We add a structure rather than a
   single parameter because there will be other fields in the phys_caps.

   The first field we add to the mlx4_phys_caps structure is num_phys_eqs.

2. In INIT_HCA, when running in SRIOV mode, the "log_num_eqs" parameter
   passed to the FW is the number of EQs per VF/PF; each function (PF or VF)
   has this number of EQs available.

   However, the total number of EQs which must be allowed for in the ICM is
   (1 << log_num_eqs) * (#VFs + #PFs).  Rather than compute this quantity,
   we allocate ICM space for 1024 EQs (which is the device maximum
   number of EQs, and which is the value we place in the mlx4_phys_caps structure).

   For INIT_HCA, however, we use the per-function number of EQs as described
   above.
Signed-off-by: NMarcel Apfelbaum <marcela@dev.mellanox.co.il>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ths fixes the comparison in the FLR (Function Level Reset) event case.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tty_lock_pair() do the right thing to avoid deadlocks, but should
instruct LOCKDEP of this to avoid a splat.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* Formatted the output of 'registers' entry
* Added "Commands in Q' to output of 'registers' entry
* Added a new entry 'flags'
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Convert macro definitions for flags bits to enum
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

When checking for command completions if the register value is zero, proceed
to next register.
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Fix to support more than one sector in exec_drive_command().
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

'cmd_issue_lock' is for only acquiring a free slot, and it is not used
in interrupt context. So replaced irq version with non-irq version of spinlock.
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Set the following block queue boundary variables
	* max_hw_sectors
	* max_segment_size
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>

Removed setting of q->nr_requests.
Signed-off-by: NJens Axboe <axboe@kernel.dk>

If a PIO (IOCTL/internal) command resulted in TFE, signal the wait event or break out of polling.
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

For the ioctl command HDIO_GET_IDENTITY, return the stored copy of IDENTIFY
DATA instead of sending the command to the device - similar to libata.
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

This change sets custom timeouts depending on PIO command.
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Fix clearing an incorrect register in mtip_init_port
Signed-off-by: NAsai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Current failure paths attempt to free resources which we failed to request
and disable resources which we failed to enable ones. This leads to kernel
oops/panic. This patch does some simple re-ordering to prevent this from
happening.

Cc: netdev@vger.kernel.org
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

disable_cb is just an optimization: it
can not guarantee that there are no callbacks.
In particular it doesn't have any effect when
event index is on.

Instead, detach, napi disable and reset on freeze ensure we don't run
concurrently with a callback.

Remove the useless calls so we get same behaviour
with and without event index.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Revert usage of acpi_wakeup_address and move definition
to x86 architecture code in order to make compilation work
in ia64.

[jsakkine: tested compilation in ia64/x86-64 and added
proper commit message]
Reported-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Originally-by: NH. Peter Anvin <hpa@kernel.org>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@intel.com>
Link: http://lkml.kernel.org/r/1338370421-27735-1-git-send-email-jarkko.sakkinen@intel.com
Cc: Tony Luck <tony.luck@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Commit  c7510859
Author: Rafael J. Wysocki <rjw@sisk.pl>
Date:   Sun Apr 12 20:06:56 2009 +0200

    PM/Hibernate: Wait for SCSI devices scan to complete during resume

Broke the scsi_wait_scan module in 2.6.30.  Apparently debian still uses it so
fix it and backport to stable before removing it in 3.6.

The breakage is caused because the function template in
include/scsi/scsi_scan.h is defined to be a nop unless SCSI is built in.
That means that in the modular case (which is every distro), the
scsi_wait_scan module does a simple async_synchronize_full() instead of
waiting for scans.

Cc: <stable@vger.kernel.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Commit a7a20d10 "[SCSI] sd: limit the scope of the async probe domain"
moved sd probe work out of reach of wait_for_device_probe().  Allow it
to be synced via scsi_complete_async_scans().
Reported-by: NMeelis Roos <mroos@linux.ee>
Tested-by: NMeelis Roos <mroos@linux.ee>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This patch should go into 3.5 fixes. The bug was added in the
patches for the 3.5 feature window.

As you can see from the patch I made a mistake. During
development I switched from passing a struct to the size of
the struct, but left the sizeof. This results in us allocating
4 bytes (sizeof(int)) but then calling pci_free_consistent
with the size of the struct.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Added support to capture dump (Minidump) which allows us to
catpure a snapshot of the firmware/hardware states at the time
of firmware failure
Signed-off-by: NTej Parkash <tej.parkash@qlogic.com>
Signed-off-by: NShyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

change_queue_depth will adjust device queuedepth upon receiving
"SAM_STAT_TASK_SET_FULL" scsi status from the target.
Also added ql4xqfulltracking command line param to enable or disable
queuefull tracking. One can disabling queuefull tracking to ensure
user set scsi device queuedepth is not altered.
Signed-off-by: NTej Parkash <tej.parkash@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Allow ddb state to change to DDB_DS_NO_CONNECTION_ACTIVE or
DDB_DS_SESSION_FAILED before issuing clear ddb mailbox cmd,
because clear ddb mailbox cmd fails if the ddb state is not
equal to DDB_DS_NO_CONNECTION_ACTIVE or DDB_DS_SESSION_FAILED.
Signed-off-by: NManish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Update the session and connection parameter before sending
connection logged in event to iscsiadm because in some
scenario logout may come in just after we send the logged
in event to user, which free up session, connection and ddb,
but DPC is still updating session and connect parameter
which can lead to panic.
Signed-off-by: NManish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Since there are uses for I2C_M_NOSTART which are much more sensible and
standard than most of the protocol mangling functionality (the main one
being gather writes to devices where something like a register address
needs to be inserted before a block of data) create a new I2C_FUNC_NOSTART
for this feature and update all the users to use it.

Also strengthen the disrecommendation of the protocol mangling while we're
at it.

In the case of regmap-i2c we remove the requirement for mangling as
I2C_M_NOSTART is the only mangling feature which is being used.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

As the bus driver side implementation of I2C_M_RECV_LEN is heavily
tied to SMBus, we can't support received length over 32 bytes, but
let's at least support that.

In practice, the caller will have to setup a buffer large enough to
cover the case where received length byte has value 32, so minimum
32 + 1 = 33 bytes, possibly more if there is a fixed number of bytes
added for the specific slave (for example a checksum.)
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Tested-by: NDouglas Gilbert <dgilbert@interlog.com>

Check for Firmware Hang (AF_FW_RECOVERY) after mailbox command
has gained access to ensure that the mailbox command does not
wait un-necessarily during a firmware recovery and prevent
premature mailbox timeout which will lead to back to back reset's.
Signed-off-by: NLalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Fix printk format warnings:

drivers/watchdog/iTCO_wdt.c:577:3: warning: format '%04llx' expects type 'long long unsigned int', but argument 2 has type 'resource_size_t'
drivers/watchdog/iTCO_wdt.c:594:3: warning: format '%04llx' expects type 'long long unsigned int', but argument 2 has type 'resource_size_t'
drivers/watchdog/iTCO_wdt.c:600:2: warning: format '%04llx' expects type 'long long unsigned int', but argument 4 has type 'resource_size_t'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>