Add an accelerator constant so almost all Cirrus are recognized as
accelerators by the fbset command.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Cirrus' Alpine and Picasso4 chips uses DAC clock doubling to achieve full
range of pixclock frequencies.

[akpm@linux-foundation.org: fix spelling, use usual comment layout]
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The 32bpp is supported only on the latest Cirrus Logic chips.  Use the
24bpp which is supported at least since Alpine chips (GD543x).

Change 32bpp mode setting to 24bpp mode.  Change acceleration as well.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Various fixes to make Cirrus GD5446 chip work.

Another Cirrus chip works with the cirrusfb.  The gd5446 seems very
similar to Alpine chips.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Balance iomap and iounmap and alloc and free calls in case of error druing
device register (probing).
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add hardware color expansion (imageblit) function.  It roughly doubles
scrolling speed of my Alpine card (GD5430).
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- Fix color expansion for 16bpp and 32bpp modes in the
  cirrusfb_RectFill().

- Make a function with a common blitter code (cirrusfb_set_blitter).

- Add fb_sync function to allow a higher layer synchronize with the
  blitter.

- Kill one redundant blitter reset.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- The Laguna GD5465 (AGP) has one register more than non-AGP chips.
  Recognize the AGP version and write a tile control register only on the
  AGP version.  Tested only on an AGP card.

- Bump up RAMDAC frequencies after X11 code.  This allow to drive a flat
  panel resolution 1680x1050 at 16bpp from the 4MB card.

- Fix screen start address overflow bits on Laguna cards (CRT1D
  register).

- Fix exit path in the cirrusfb_pci_register() in case of error.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Break cirrusfb_decode_var() function into two parts:
cirrusfb_check_pixclock() which can be called from the
cirrusfb_check_var() aand merge rest into the cirrusfb_set_par_foo().
This allows rejecting modes with too high pixclock before before any
change to hardware state (and a console is messed up).

Also, fix RGB field's lengths for 8bpp modes to correct ones so X11 works
with fbdev driver with cirrusfb.

Kill some redundant function calls or register loads.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix 8bpp mode by adding handling of the Laguna chipsets to various places
and stop trashing a HDR register which probably does not exist on the
Laguna.

Fix compilation warnings about uninitialized variables also.

Finally, all 8bpp, 16bpp and 32bpp modes work on the Laguna chipset.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Various improvements to the code:
- kill a structure with only one
  field: multiplexing and use the
  field directly
- move the cirrusfb_ops structure
  down the file to kill forward
  declarations
- move cirrusfb_init() to kill
  forward declaration
- kill register loads done already
  in the init_vgachip()
- kill assigments done by higher
  layer in the cirrusfb_pan_display()
- do not overwrite line pitch bit in
  the CL_CRT1D register
- kill btype variables if they were
  used only once or twice
- add cpu_relax() in the busy waiting
  loop

The fix to the CL_CRT1D register handling makess the 1024x768 32bpp mode
work.  Previously, only lower resolution modes have worked with 32bpp.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the 5-6-5 RGB mode instead of the 5-5-5 mode at 16bpp depth.

It fixes colors in the 16bpp modes on Cirrus Laguna chips.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert.uytterhoeven@gmail.com>
Cc: Arthur Marsh <arthur.marsh@internode.on.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A line length is calculated twice: first in the cirrusfb_decode_var() then
in the cirrusfb_set_par_foo().

Use the first calculated value.  A nice side effect is that 32bpp mode
works now.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert.uytterhoeven@gmail.com>
Cc: Arthur Marsh <arthur.marsh@internode.on.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The Laguna chipsets use special registers which are available through the
mmio area.  The cirrusfb driver does not use memory mapped registers for
the PCI cards.

Add the memory mapped area for Laguna chipsets and add basic usage of the
special Laguna registers after SVGALIB code.

This gives readable console at 16bpp on the GD-5465 (Laguna AGP).  The
8bpp and 32bpp depths are still broken.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add additional overflow register setting for Laguna chips.

Also, simplify some code in the cirrusfb_pan_display() and
cirrusfb_blank().
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix memory detection and clock setting for Cirrus Laguna chipsets
(GD5464/GD5465).  The changes are done after the Xorg code.

The driver still does not display anything on the GD5465 but it switches
resolutions correctly at least.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert all printks to dev_dbg, dev_info or dev_err.  Kill some excessive
debug information and code in the process.

[akpm@linux-foundation.org: printk fixes]
[akpm@linux-foundation.org: cleanups]
Signed-off-by: NKrzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix trailing whitespace because quilt complained about it.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

GFP_KERNEL is legal here - we don't need to use gfp_any().

Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

new_alarm is unsigned so test before the subtraction.

[akpm@linux-foundation.org: time-wrapping fix]
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With a postfix decrement retries will reach -1 rather than 0, so the
warning and error-out will not occur.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the EPSON RX8025 RTC.  The date/time registers of this
chip are compatible with the DS1307.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: NAlessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow the rtc-ds1307 driver to work with SMBus controllers like nforce2
that do not support i2c block transfers.
Signed-off-by: NEd Swierk <eswierk@aristanetworks.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: BARRE Sebastien <sbarre@sdelcc.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Ndann frazier <dannf@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Ndann frazier <dannf@hp.com>
Reviewed-by: NGrant Grundler <grundler@parisc-linux.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Ndann frazier <dannf@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Ndann frazier <dannf@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This isn't a hotpluggable device, so call platform_driver_probe
directly in parisc_rtc_init
Signed-off-by: Ndann frazier <dannf@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the return value of rtc_valid_tm() instead of just returning 0.
Signed-off-by: Ndann frazier <dannf@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

parisc_rtc now only includes an rtc_device pointer, so let's
just use the rtc_device type directly.
Signed-off-by: Ndann frazier <dannf@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The RTC subsystem proides ops locking, no need to implement our own
Signed-off-by: Ndann frazier <dannf@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Ndann frazier <dannf@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Munge Stephane Eranian's efirtc.c code into an rtc platform driver

[akpm@linux-foundation.org: use is_leap_year()]
Signed-off-by: Ndann frazier <dannf@hp.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Cc: stephane eranian <eranian@googlemail.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- the LEAP_YEAR macro is buggy - it references its arg multiple times.
  Fix this by turning it into a C function.

- give it a more approriate name

- Move it to rtc.h so that other .c files can use it, instead of copying it.

Cc: dann frazier <dannf@hp.com>
Acked-by: NAlessandro Zummo <alessandro.zummo@towertech.it>
Cc: stephane eranian <eranian@googlemail.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

These are the only two ioctls so the ioctl() function is also removed.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

autofs_dev-ioctl.h is included by both the kernel module and user space tools
and it includes two kernel header files.  Compiles work if the kernel headers
are installed but fail otherwise.
Signed-off-by: NIan Kent <raven@themaw.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A deadlock can occur when user space uses a signal (autofs version 4 uses
SIGCHLD for this) to effect expire completion.

The order of events is:

Expire process completes, but before being able to send SIGCHLD to it's parent
...

Another process walks onto a different mount point and drops the directory
inode semaphore prior to sending the request to the daemon as it must ...

A third process does an lstat on on the expired mount point causing it to wait
on expire completion (unfortunately) holding the directory semaphore.

The mount request then arrives at the daemon which does an lstat and,
deadlock.

For some time I was concerned about releasing the directory semaphore around
the expire wait in autofs4_lookup as well as for the mount call back.  I
finally realized that the last round of changes in this function made the
expiring dentry and the lookup dentry separate and distinct so the check and
possible wait can be done anywhere prior to the mount call back.  This patch
moves the check to just before the mount call back and inside the directory
inode mutex release.
Signed-off-by: NIan Kent <raven@themaw.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A significant portion of the autofs_dev_ioctl_expire() and
autofs4_expire_multi() functions is duplicated code.  This patch cleans that
up.
Signed-off-by: NIan Kent <raven@themaw.net>
Signed-off-by: NJeff Moyer <jmoyer@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use kzfree() instead of memset() + kfree().
Signed-off-by: NJohannes Weiner <hannes@cmpxchg.org>
Reviewed-by: NPekka Enberg <penberg@cs.helsinki.fi>
Acked-by: NTyler Hicks <tyhicks@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>