The intel_dp_autotest_video_pattern() function gets invoked through the
compliance test handler on a HPD short pulse if the test type is
set to DP_TEST_VIDEO_PATTERN. This performs the DPCD registers
reads to read the requested test pattern, video pattern resolution,
frame rate and bits per color value. The results of this analysis
are handed off to userspace so that the userspace app can set the
video pattern mode appropriately for the test result/response.
When the  test is requested with specific BPC value, we read the BPC
value from the DPCD register. If this BPC value in intel_dp structure
has a non-zero value and we're on a display port connector, then we use
the value to calculate the bpp for the pipe. Also in this case if its
a 18bpp video pattern request, then we force the dithering on pipe to be
disabled since it causes CRC mismatches.

The compliance_test_active flag is set at the end of the individual
test handling functions. This is so that the kernel-side operations
can be completed without the risk of interruption from the userspace
app that is polling on that flag.

v5:
* Remove test_result variable
* Populate the compliance test data at the end of the function (Jani Nikula)
v4:
*Return TEST_NAK on read failures and invalid values (Jani Nikula)
* Address CRC mismatch errors
v3:
* Use the updated properly shifted bit definitions (Jani Nikula)
* Force dithering to be disabled on 18bpp compliance
test request (Manasi Navare)
v2:
* Updated the DPCD Register reads based on proper defines in header (Jani Nikula)
* Squahsed the patch that forced the pipe bpp to compliance test bpp (Jani Nikula)
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485274909-17470-1-git-send-email-manasi.d.navare@intel.com

This patch addresses a few issues from the original patch for
DP Compliance EDID test support submitted by
Todd Previte<todd.previte@gmail.com>

Video Mode requested in the EDID test handler for the EDID Read
test (CTS 4.2.2.3) should be set to PREFERRED as per the CTS spec.

v2:
* Added read debugfs data from test_data.edid if its EDID test (Jani NIkula)
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484968170-12467-3-git-send-email-manasi.d.navare@intel.com

This patch adds support to handle automated DP compliance
link training test requests. This patch has been tested with
Unigraf DPR-120 DP Compliance device for testing Link
Training Compliance.
After we get a short pulse Compliance test request, test
request values are read and hotplug uevent is sent in order
to trigger another modeset during which the pipe is configured
and link is retrained and enabled for link parameters requested
by the test.

v5:
* Only modify the compliance structure after all validation
is done (Jani Nikula)
* Remove the variable test_result (Jani Nikula)
v4:
* Return TEST_NAK for read failures and invalid
values (Jani Nikula)
* Conver the test link BW to link rate before storing (Jani Nikula)
v3:
* Validate the test link rate and lane count as soon as
the request comes (Jani Nikula)
v2:
* Validate the test lane count before using it in
intel_dp_compute_config (Jani Nikula)
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485274594-17361-1-git-send-email-manasi.d.navare@intel.com

Remove WaGsvDisableTurbo and WaRsUseTimeoutMode as these were only for
pre-production Broxton devices, and this code is now defunct.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Along with GLK it was introduced the .is_lp and IS_GEN9_LP.
So, following the same simplification standard we can
put Skylake and Kabylake under the same bucket for most
of the things.

So let's add the IS_GEN9_BC for "Big Core" (non Atom based
platforms).

The i915_drv.c was let out of this patch on purpose
because that is really a decision per platform, just like
other cases where IS_KABYLAKE is different from IS_SKYLAKE.

v2: fix conflict with IS_LP and 3 new cases for this
    big core bucket:
    - intel_ddi.c: intel_ddi_get_link_dpll
    - intel_fbc.c: find_compression_threshold
    - i915_gem_gtt.c: gtt_write_workarounds

Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485196357-30599-2-git-send-email-rodrigo.vivi@intel.com

According to wa_database this Wa persist on KBL as it was on SKL.

Cc: Tim Gore <tim.gore@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485196357-30599-1-git-send-email-rodrigo.vivi@intel.com

Fences are required to support being released from under an atomic context.
The drm_atomic_state struct may take a mutex when being released and so
we cannot drop a reference to the drm_atomic_state from the fence release
path directly, and so we need to defer that unreference to a worker.

[  326.576697] WARNING: CPU: 2 PID: 366 at kernel/sched/core.c:7737 __might_sleep+0x5d/0x80
[  326.576816] do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffffc0359549>] intel_breadcrumbs_signaler+0x59/0x270 [i915]
[  326.576818] Modules linked in: rfcomm fuse snd_hda_codec_hdmi bnep snd_hda_codec_realtek snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq snd_seq_device snd_timer input_leds led_class snd punit_atom_debug btusb btrtl btbcm btintel intel_rapl bluetooth i915 drm_kms_helper syscopyarea sysfillrect iwlwifi sysimgblt soundcore fb_sys_fops mei_txe cfg80211 drm pwm_lpss_platform pwm_lpss pinctrl_cherryview fjes acpi_pad parport_pc ppdev parport autofs4
[  326.576899] CPU: 2 PID: 366 Comm: i915/signal:0 Tainted: G     U          4.10.0-rc3-patser+ #5030
[  326.576902] Hardware name:                  /NUC5PPYB, BIOS PYBSWCEL.86A.0031.2015.0601.1712 06/01/2015
[  326.576905] Call Trace:
[  326.576920]  dump_stack+0x4d/0x6d
[  326.576926]  __warn+0xc0/0xe0
[  326.576931]  warn_slowpath_fmt+0x5a/0x80
[  326.577004]  ? intel_breadcrumbs_signaler+0x59/0x270 [i915]
[  326.577075]  ? intel_breadcrumbs_signaler+0x59/0x270 [i915]
[  326.577079]  __might_sleep+0x5d/0x80
[  326.577087]  mutex_lock+0x1b/0x40
[  326.577133]  drm_property_free_blob+0x1e/0x80 [drm]
[  326.577167]  ? drm_property_destroy+0xe0/0xe0 [drm]
[  326.577200]  drm_mode_object_unreference+0x5c/0x70 [drm]
[  326.577233]  drm_property_unreference_blob+0xe/0x10 [drm]
[  326.577260]  __drm_atomic_helper_crtc_destroy_state+0x14/0x40 [drm_kms_helper]
[  326.577278]  drm_atomic_helper_crtc_destroy_state+0x10/0x20 [drm_kms_helper]
[  326.577352]  intel_crtc_destroy_state+0x9/0x10 [i915]
[  326.577388]  drm_atomic_state_default_clear+0xea/0x1d0 [drm]
[  326.577462]  intel_atomic_state_clear+0xd/0x20 [i915]
[  326.577497]  drm_atomic_state_clear+0x1a/0x30 [drm]
[  326.577532]  __drm_atomic_state_free+0x13/0x60 [drm]
[  326.577607]  intel_atomic_commit_ready+0x6f/0x78 [i915]
[  326.577670]  i915_sw_fence_release+0x3a/0x50 [i915]
[  326.577733]  dma_i915_sw_fence_wake+0x39/0x80 [i915]
[  326.577741]  dma_fence_signal+0xda/0x120
[  326.577812]  ? intel_breadcrumbs_signaler+0x59/0x270 [i915]
[  326.577884]  intel_breadcrumbs_signaler+0xb1/0x270 [i915]
[  326.577889]  kthread+0x127/0x130
[  326.577961]  ? intel_engine_remove_wait+0x1a0/0x1a0 [i915]
[  326.577964]  ? kthread_stop+0x120/0x120
[  326.577970]  ret_from_fork+0x22/0x30

Fixes: c004a90b ("drm/i915: Restore nonblocking awaits for modesetting")
Reported-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170123212939.30345-1-chris@chris-wilson.co.uk
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.10-rc1+
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

When introduced, I thought that reducing client latency from the
signaler was the priority. Since its inception the signaler has become
responsible for keeping the execlists full, via the dma-fence. As this
is very important to minimise overall execution time, signal the
dma-fence first and then signal any waiting clients.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170124110009.28947-8-chris@chris-wilson.co.uk

If the second ELSP port is available, schedule the execlists tasklet to
see if the new request can occupy it.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170124110009.28947-7-chris@chris-wilson.co.uk

Only the first request added to the execlist queue can be submitted. If
this request is not the first request on the queue, it means that there
are already higher priority requests waiting upon the tasklet and
kicking it will make no difference.

This is more relevant for a later patch, where we more eagerly try and
kick the tasklet to handle the submission of new requests.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170124110009.28947-6-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>

If the CSB head/tail pointers are unchanged, we can skip the update of
the CSB register afterwards.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170124110009.28947-5-chris@chris-wilson.co.uk

Mark when we run the execlist tasklet following the interrupt, so we
don't probe a potentially uninitialised register when submitting the
contexts multiple times before the hardware responds.

v2: Use a shared engine->irq_posted
v3: Always use locked bitops to be sure of atomicity wrt to other bits
in the mask.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170124152021.26587-1-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>

In the next patch, we will use the irq_posted technique for another
engine interrupt, rather than use two members for the atomic updates, we
can use two bits of one instead. First, we need to update the
breadcrumbs to use the new common engine->irq_posted.

v2: Use set_bit() rather than __set_bit() to ensure atomicity with
respect to other bits in the mask
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170124151805.26146-1-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>

We need to prevent resubmission of the context immediately following an
initial resubmit (which does a lite-restore preemption). Currently we do
this by disabling all submission whilst the context is still active, but
we can improve this by limiting the restriction to only until we
receive notification from the context-switch interrupt that the
lite-restore preemption is complete.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170124110009.28947-2-chris@chris-wilson.co.uk

To complement the check in execlists_elsp_ready(), also assert that we
don't submit the same context while it has a lite restore still pending.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170124110009.28947-1-chris@chris-wilson.co.uk

There is no point in setting intel_dp->compliance.test_type, and
proceeding with the autotests, if we're about to NAK the request. Some
drive-by cleanups while at it.

v2: look at the ACK bit, as the result may also contain
    TEST_EDID_CHECKSUM_WRITE

Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Tested-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484931846-25390-1-git-send-email-jani.nikula@intel.com

The GPU may be in an unknown state following resume and module load. The
previous occupant may have left contexts loaded, or other dangerous
state, which can cause an immediate GPU hang for us. The only save
course of action is to reset the GPU prior to using it - similarly to
how we reset the GPU prior to unload (before a second user may be
affected by our leftover state).

We need to reset the GPU very early in our load/resume sequence so that
any stale HW pointers are revoked prior to any resource allocations we
make (that may conflict).

A reset should only be a couple of milliseconds on a slow device, a cost
we should easily be able to absorb into our initialisation times.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170124110135.6418-2-chris@chris-wilson.co.uk

In order to reset the GPU early on in the module load sequence, we need
to allocate the basic engine structs (to populate the mmio offsets etc).
Currently, the engine initialisation allocates both the base struct and
also allocate auxiliary objects, which depend upon state setup quite
late in the load sequence. We split off the allocation callback for
later and allow ourselves to allocate the engine structs themselves
early.

v2: Different paint for the unwind following error.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170124110135.6418-1-chris@chris-wilson.co.uk

This w/a (WaClearTdlStateAckDirtyBits) was only used for preproduction hw,
which is no longer in use. Remove the workaround to simplify the code.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170123130601.2281-5-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

This w/a (WaSetDisablePixMaskCammingAndRhwoInCommonSliceChicken) was only
used for preproduction hw, which is no longer in use. Remove the
workaround to simplify the code.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170123130601.2281-4-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

This w/a (WaDisableCtxRestoreArbitration) was only used for preproduction
hw, which is no longer in use. Remove the workaround to simplify the code.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170123130601.2281-3-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

This w/a was only used for preproduction hw, which is no longer in use.
Remove the workaround to simplify the code.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170123130601.2281-2-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

This w/a (WaEnableForceRestoreInCtxtDescForVCS) was only used for
preproduction hw, which is no longer in use.  Remove the workaround to
simplify the code.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170123130601.2281-1-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Since tweaking i915_vma_compare() we allowed constructors to skip
clearing the ggtt_view believing that we didn't access the unused
members. That, as it turns out, was not entirely true. In particular,
i915_gem_fault() uses

    ret = remap_io_mapping(area,
	    area->vm_start + (vma->ggtt_view.partial.offset << PAGE_SHIFT),
	    (ggtt->mappable_base + vma->node.start) >> PAGE_SHIFT,
	    min_t(u64, vma->size, area->vm_end - area->vm_start),
	    &ggtt->mappable);

i.e. the ggtt_view.partial for both normal and partial views. If we
allowed garbage into the normal vma->ggtt_view and then try userspace
tried to mmap it, we could explode in an unobvious fashion.

Fixes: 7b92c047 ("drm/i915: Eliminate superfluous i915_ggtt_view_rotated")
Fixes: 3bf4d575 ("drm/i915: Stop clearing i915_ggtt_view")
Reported-by: NMatthew Auld <matthew.william.auld@gmail.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170123145245.3972-1-chris@chris-wilson.co.ukTested-by: NMatthew Auld <matthew.auld@intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>

This reverts commit 527b6abe
(Revert "drm/i915: Use atomic commits for legacy page_flips")

and reapplies commit ee042aa4.
("drm/i915: Use atomic commits for legacy page_flips")

The reason for the revert was because legacy cursor updates were
forced to wait for pending page flips and rendering after they
were converted to atomic.

Commit f79f2692
(drm/i915: Add a cursor hack to allow converting legacy page flip to atomic, v3)
adds a fastpath to cursor updates, which fixes the stuttering issues.
With these changes I feel confident enough to re-enable cursor updates.

Legacy cursor update won't block in the following cases:
- Moving cursor
- Changing cursor fb

The legacy cursor update will still block in the following cases:
- Showing/hiding cursor.
- Cursor size or scaling changes.
- cursor update while cursor is invisible (could be fixed, if it turns out to be important).
- Cursor tiling changes (Not sure we support tiled cursors.)
- Last update was a modeset.

Cc: Steven Newbury <steve@snewbury.org.uk>
Cc: Rafael Ristovski <rafael.ristovski@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: NRafael Ristovski <rafael.ristovski@gmail.com>
Testcase: igt/kms_cursor_legacy
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When execlists signals the context completion, it also provides the
context id for the status event. Assert that id matches the one we expect.

v2: The upper dword of the context status is a duplicate of the upper
dword from elsp submission (i.e. includes the group id as well as the
context id). Include this check as well.
v3: Only check against lrc_desc (as this contains the hw_id check)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170123113132.18665-2-chris@chris-wilson.co.uk

For easy recognisability, we want the kernel context to have id 0 and
all user contexts to have non-zero ids.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170123113132.18665-1-chris@chris-wilson.co.uk

Ensure that the hangcheck is queued even in the absence of interrupts.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170123093724.18592-1-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>

To make the code clearer, use rb_entry() instead of container_of() to
deal with rbtree.
Signed-off-by: NGeliang Tang <geliangtang@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/b08fd4be9d4c45d88c158a17b854c3fd628840ed.1484816339.git.geliangtang@gmail.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

drivers/gpu/drm/i915/intel_csr.c: In function ‘csr_load_work_fn’:
drivers/gpu/drm/i915/intel_csr.c:399:6: error: variable ‘ret’ set but not used [-Werror=unused-but-set-variable]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170118121808.27869-2-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>

Move the intel_fake_agp_sizes array into the same #ifdef block as it is
used to avoid instantiation when not used, and so triggering a compiler
warning

drivers/char/agp/intel-gtt.c:335:42: warning: ‘intel_fake_agp_sizes’
defined but not used [-Wunused-const-variable=]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170121182233.30852-1-chris@chris-wilson.co.ukReviewed-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

In intel_crtc_disable_noatomic(), bail on a failure to allocate an
atomic state to avoid a NULL pointer dereference.

Fixes: 4a806558 ("drm/i915: Pass atomic state to crtc enable/disable functions")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484922525-6131-4-git-send-email-ander.conselvan.de.oliveira@intel.com

Parameters tile_size, tile_width and tile_height were passed in the
wrong order to _intel_adjust_tile_offset() when calculating the rotated
offsets.

This doesn't fix any user visible bug, since for packed formats new
and old offset are the same and the rotated offsets are within a tile
before they are fed to _intel_adjust_tile_offset(). In that case, the
offsets are unchanged. That is not true for planar formats, but those
are currently not supported.

Fixes: 66a2d927 ("drm/i915: Make intel_adjust_tile_offset() work for linear buffers")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484922525-6131-3-git-send-email-ander.conselvan.de.oliveira@intel.com

An error in the condition for avoiding the call to intel_hpd_poll_init()
for valleyview and cherryview from intel_runtime_suspend() caused it to
be called unconditionally. Fix it.

Fixes: 19625e85 ("drm/i915: Enable polling when we don't have hpd")
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Lyude <cpaul@redhat.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484922525-6131-2-git-send-email-ander.conselvan.de.oliveira@intel.com

In the path where intel_crt_detect_ddc() detects a CRT, if would return
true without freeing the edid.

Fixes: a2bd1f54 ("drm/i915: check whether we actually received an edid in detect_ddc")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v3.6+
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484922525-6131-1-git-send-email-ander.conselvan.de.oliveira@intel.com

Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The call went away in:

commit 3b16525c
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Thu Aug 4 16:32:25 2016 +0100

    drm/i915: Split insertion/binding of an object into the VM

It is useful to have this trace as it pairs nicely with the vma_unbind
one to track vma activity.
Added inside the i915_vma_bind function (was outside before) to keep a
similar placement as trace_i915_vma_unbind.

v2: print bind_flags instead of flags (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484949083-11430-1-git-send-email-daniele.ceraolospurio@intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

VMA (and their objects) are supposed to composed of whole pages. Add an
assert to catch any invalid construct when we create the VMA.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170119192659.31789-6-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Before moving the vma between the VM active/inactive lists, assert that
the node is still allocated.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170119192659.31789-5-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

When pinning into the global GTT, an error from creating the VMA is
unlikely, so mark it so.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170119192659.31789-4-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>