The ath10k reports the random_mac_addr capability to upper layer
based on the service bit firmware reported. Driver sets the
spoofed flag in scan_ctrl_flag to firmware if upper layer has
enabled this feature in scan request.

Test with QCA6174 hw3.0 and firmware-6.bin_WLAN.RM.4.4.1-00102-QCARMSWP-1,
but QCA9377 is also affected.
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

These wrappers makes the HTT ops align better with the HIF ops
(where similar wrappers are used).

It also makes it easier for a target to have unsupported ops
(by letting the corresponding function pointer be NULL).
Signed-off-by: NErik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch fixes regression caused by 0c317a02
("cfg80211: support virtual interfaces with different beacon intervals"),
with this change cfg80211 expects the driver to advertize
'beacon_int_min_gcd' to support different beacon intervals in multivap
scenario. This support is added for, QCA988X/QCA99X0/QCA9984/QCA4019.

Verifed AP + mesh bring up on QCA9984 with beacon interval 100msec and
1000msec respectively.
Frimware: firmware-5.bin_10.4-3.5.3-00053

Fixes: 0c317a02 ("cfg80211: support virtual interfaces with different beacon intervals")
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For WPA encryption, QCA6174 firmware(version: WLAN.RM.4.4) will unblock
data when M4 was sent successfully. For other encryption which didn't need
4-way handshake firmware will unblock the data when peer authorized. Since
TDLS is 3-way handshake host need send authorize cmd to firmware to unblock
data.
Signed-off-by: NYingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

TDLS peer do not need WEP key. Setting WEP key will lead
to TDLS setup failure. Add fix to avoid setting WEP key
for TDLS peer.
Signed-off-by: NYingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Enable TDLS peer buffer STA feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS peer buffer STA,
it reports this capability through wmi service map in wmi service ready
event. Set related parameter in TDLS WMI command to enable this feature.
Signed-off-by: NYingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This reverts commit 55884c04.

When Ath10k is in AP mode and an unassociated STA sends a VHT action frame
(Operating Mode Notification for the NSS change) periodically to AP this causes
ath10k to call ath10k_station_assoc() which sends WMI_PEER_ASSOC_CMDID during
NSS update. Over the time (with a certain client it can happen within 15 mins
when there are over 500 of these VHT action frames) continuous calls of
WMI_PEER_ASSOC_CMDID cause firmware to assert due to resource exhaust.

To my knowledge setting WMI_PEER_NSS peer param itself enough to handle NSS
updates and no need to call ath10k_station_assoc(). So revert the original
commit from 2014 as it's unclear why the change was really needed.
Now the firmware assert doesn't happen anymore.

Issue observed in QCA9984 platform with firmware version:10.4-3.5.3-00053.
This Change tested in QCA9984 with firmware version: 10.4-3.5.3-00053 and
QCA988x platform with firmware version: 10.2.4-1.0-00036.

Firmware Assert log:

ath10k_pci 0002:01:00.0: firmware crashed! (guid e61f1274-9acd-4c5b-bcca-e032ea6e723c)
ath10k_pci 0002:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
ath10k_pci 0002:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 1 testmode 1
ath10k_pci 0002:01:00.0: firmware ver 10.4-3.5.3-00053 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast crc32 4c56a386
ath10k_pci 0002:01:00.0: board_file api 2 bmi_id 0:4 crc32 c2271344
ath10k_pci 0002:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1
ath10k_pci 0002:01:00.0: firmware register dump:
ath10k_pci 0002:01:00.0: [00]: 0x0000000A 0x000015B3 0x00981E5F 0x00975B31
ath10k_pci 0002:01:00.0: [04]: 0x00981E5F 0x00060530 0x00000011 0x00446C60
ath10k_pci 0002:01:00.0: [08]: 0x0042F1FC 0x00458080 0x00000017 0x00000000
ath10k_pci 0002:01:00.0: [12]: 0x00000009 0x00000000 0x00973ABC 0x00973AD2
ath10k_pci 0002:01:00.0: [16]: 0x00973AB0 0x00960E62 0x009606CA 0x00000000
ath10k_pci 0002:01:00.0: [20]: 0x40981E5F 0x004066DC 0x00400000 0x00981E34
ath10k_pci 0002:01:00.0: [24]: 0x80983B48 0x0040673C 0x000000C0 0xC0981E5F
ath10k_pci 0002:01:00.0: [28]: 0x80993DEB 0x0040676C 0x00431AB8 0x0045D0C4
ath10k_pci 0002:01:00.0: [32]: 0x80993E5C 0x004067AC 0x004303C0 0x0045D0C4
ath10k_pci 0002:01:00.0: [36]: 0x80994AAB 0x004067DC 0x00000000 0x0045D0C4
ath10k_pci 0002:01:00.0: [40]: 0x809971A0 0x0040681C 0x004303C0 0x00441B00
ath10k_pci 0002:01:00.0: [44]: 0x80991904 0x0040688C 0x004303C0 0x0045D0C4
ath10k_pci 0002:01:00.0: [48]: 0x80963AD3 0x00406A7C 0x004303C0 0x009918FC
ath10k_pci 0002:01:00.0: [52]: 0x80960E80 0x00406A9C 0x0000001F 0x00400000
ath10k_pci 0002:01:00.0: [56]: 0x80960E51 0x00406ACC 0x00400000 0x00000000
ath10k_pci 0002:01:00.0: Copy Engine register dump:
ath10k_pci 0002:01:00.0: index: addr: sr_wr_idx: sr_r_idx: dst_wr_idx: dst_r_idx:
ath10k_pci 0002:01:00.0: [00]: 0x0004a000 15 15 3 3
ath10k_pci 0002:01:00.0: [01]: 0x0004a400 17 17 212 213
ath10k_pci 0002:01:00.0: [02]: 0x0004a800 21 21 20 21
ath10k_pci 0002:01:00.0: [03]: 0x0004ac00 25 25 27 25
ath10k_pci 0002:01:00.0: [04]: 0x0004b000 515 515 144 104
ath10k_pci 0002:01:00.0: [05]: 0x0004b400 28 28 155 156
ath10k_pci 0002:01:00.0: [06]: 0x0004b800 12 12 12 12
ath10k_pci 0002:01:00.0: [07]: 0x0004bc00 1 1 1 1
ath10k_pci 0002:01:00.0: [08]: 0x0004c000 0 0 127 0
ath10k_pci 0002:01:00.0: [09]: 0x0004c400 1 1 1 1
ath10k_pci 0002:01:00.0: [10]: 0x0004c800 0 0 0 0
ath10k_pci 0002:01:00.0: [11]: 0x0004cc00 0 0 0 0
ath10k_pci 0002:01:00.0: CE[1] write_index 212 sw_index 213 hw_index 0 nentries_mask 0x000001ff
ath10k_pci 0002:01:00.0: CE[2] write_index 20 sw_index 21 hw_index 0 nentries_mask 0x0000007f
ath10k_pci 0002:01:00.0: CE[5] write_index 155 sw_index 156 hw_index 0 nentries_mask 0x000001ff
ath10k_pci 0002:01:00.0: DMA addr: nbytes: meta data: byte swap: gather:
ath10k_pci 0002:01:00.0: [455]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [456]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [457]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [458]: 0x594a0038 0 0 0 1
ath10k_pci 0002:01:00.0: [459]: 0x580c0a42 0 0 0 0
ath10k_pci 0002:01:00.0: [460]: 0x594a0060 0 0 0 1
ath10k_pci 0002:01:00.0: [461]: 0x580c0c42 0 0 0 0
ath10k_pci 0002:01:00.0: [462]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [463]: 0x580c0c42 0 0 0 0
ath10k_pci 0002:01:00.0: [464]: 0x594a0038 0 0 0 1
ath10k_pci 0002:01:00.0: [465]: 0x580c0a42 0 0 0 0
ath10k_pci 0002:01:00.0: [466]: 0x594a0060 0 0 0 1
ath10k_pci 0002:01:00.0: [467]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [468]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [469]: 0x580c1c42 0 0 0 0
ath10k_pci 0002:01:00.0: [470]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [471]: 0x580c1c42 0 0 0 0
ath10k_pci 0002:01:00.0: [472]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [473]: 0x580c1c42 0 0 0 0
ath10k_pci 0002:01:00.0: [474]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [475]: 0x580c0642 0 0 0 0
ath10k_pci 0002:01:00.0: [476]: 0x594a0038 0 0 0 1
ath10k_pci 0002:01:00.0: [477]: 0x580c0842 0 0 0 0
ath10k_pci 0002:01:00.0: [478]: 0x594a0060 0 0 0 1
ath10k_pci 0002:01:00.0: [479]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [480]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [481]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [482]: 0x594a0038 0 0 0 1
ath10k_pci 0002:01:00.0: [483]: 0x580c0842 0 0 0 0
ath10k_pci 0002:01:00.0: [484]: 0x594a0060 0 0 0 1
ath10k_pci 0002:01:00.0: [485]: 0x580c0642 0 0 0 0
ath10k_pci 0002:01:00.0: [486]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [487]: 0x580c0642 0 0 0 0
ath10k_pci 0002:01:00.0: [488]: 0x594a0038 0 0 0 1
ath10k_pci 0002:01:00.0: [489]: 0x580c0842 0 0 0 0
ath10k_pci 0002:01:00.0: [490]: 0x594a0060 0 0 0 1
ath10k_pci 0002:01:00.0: [491]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [492]: 0x58174040 0 1 0 0
ath10k_pci 0002:01:00.0: [493]: 0x5a946040 0 1 0 0
ath10k_pci 0002:01:00.0: [494]: 0x59909040 0 1 0 0
ath10k_pci 0002:01:00.0: [495]: 0x5ae5a040 0 1 0 0
ath10k_pci 0002:01:00.0: [496]: 0x58096040 0 1 0 0
ath10k_pci 0002:01:00.0: [497]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [498]: 0x580c0642 0 0 0 0
ath10k_pci 0002:01:00.0: [499]: 0x5c1e0040 0 1 0 0
ath10k_pci 0002:01:00.0: [500]: 0x58153040 0 1 0 0
ath10k_pci 0002:01:00.0: [501]: 0x58129040 0 1 0 0
ath10k_pci 0002:01:00.0: [502]: 0x5952f040 0 1 0 0
ath10k_pci 0002:01:00.0: [503]: 0x59535040 0 1 0 0
ath10k_pci 0002:01:00.0: [504]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [505]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [506]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [507]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [508]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [509]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [510]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [511]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [512]: 0x5adcc040 0 1 0 0
ath10k_pci 0002:01:00.0: [513]: 0x5cf3d040 0 1 0 0
ath10k_pci 0002:01:00.0: [514]: 0x5c1e9040 64 1 0 0
ath10k_pci 0002:01:00.0: [515]: 0x00000000 0 0 0 0
Signed-off-by: NKarthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When attempt to run worker (ath10k_sta_rc_update_wk) after the station object
(ieee80211_sta) delete will trigger the kernel panic.

This problem arise in AP + Mesh configuration, Where the current node AP VAP
and neighbor node mesh VAP MAC address are same. When the current mesh node
try to establish the mesh link with neighbor node, driver peer creation for
the neighbor mesh node fails due to duplication MAC address. Already the AP
VAP created with same MAC address.

It is caused by the following scenario steps.

Steps:
1. In above condition, ath10k driver sta_state callback (ath10k_sta_state)
   fails to do the state change for a station from IEEE80211_STA_NOTEXIST
   to IEEE80211_STA_NONE due to peer creation fails. Sta_state callback is
   called from ieee80211_add_station() to handle the new station
   (neighbor mesh node) request from the wpa_supplicant.
2. Concurrently ath10k receive the sta_rc_update callback notification from
   the mesh_neighbour_update() to handle the beacon frames of the above
   neighbor mesh node. since its atomic callback, ath10k driver queue the
   work (ath10k_sta_rc_update_wk) to handle rc update.
3. Due to driver sta_state callback fails (step 1), mac80211 free the station
   object.
4. When the worker (ath10k_sta_rc_update_wk) scheduled to run, it will access
   the station object which is already deleted. so it will trigger kernel
   panic.

Added the peer exist check in sta_rc_update callback before queue the work.

Kernel Panic log:

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0204000
[00000000] *pgd=00000000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
CPU: 1 PID: 1833 Comm: kworker/u4:2 Not tainted 3.14.77 #1
task: dcef0000 ti: d72b6000 task.ti: d72b6000
PC is at pwq_activate_delayed_work+0x10/0x40
LR is at pwq_activate_delayed_work+0xc/0x40
pc : [<c023f988>]    lr : [<c023f984>]    psr: 40000193
sp : d72b7f18  ip : 0000007a  fp : d72b6000
r10: 00000000  r9 : dd404414  r8 : d8c31998
r7 : d72b6038  r6 : 00000004  r5 : d4907ec8  r4 : dcee1300
r3 : ffffffe0  r2 : 00000000  r1 : 00000001  r0 : 00000000
Flags: nZcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c5787d  Table: 595bc06a  DAC: 00000015
...
Process kworker/u4:2 (pid: 1833, stack limit = 0xd72b6238)
Stack: (0xd72b7f18 to 0xd72b8000)
7f00:                                                       00000001 dcee1300
7f20: 00000001 c02410dc d8c31980 dd404400 dd404400 c0242790 d8c31980 00000089
7f40: 00000000 d93e1340 00000000 d8c31980 c0242568 00000000 00000000 00000000
7f60: 00000000 c02474dc 00000000 00000000 000000f8 d8c31980 00000000 00000000
7f80: d72b7f80 d72b7f80 00000000 00000000 d72b7f90 d72b7f90 d72b7fac d93e1340
7fa0: c0247404 00000000 00000000 c0208d20 00000000 00000000 00000000 00000000
7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
7fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<c023f988>] (pwq_activate_delayed_work) from [<c02410dc>] (pwq_dec_nr_in_flight+0x58/0xc4)
[<c02410dc>] (pwq_dec_nr_in_flight) from [<c0242790>] (worker_thread+0x228/0x360)
[<c0242790>] (worker_thread) from [<c02474dc>] (kthread+0xd8/0xec)
[<c02474dc>] (kthread) from [<c0208d20>] (ret_from_fork+0x14/0x34)
Code: e92d4038 e1a05000 ebffffbc[69210.619376] SMP: failed to stop secondary CPUs
Rebooting in 3 seconds..
Signed-off-by: NKarthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

WCN3990 sends mgmt frames by reference via WMI.
The host dma maps the mgmt frame and sends the physical
address to the firmware in the wmi command. Since the
dma mapping is done in the gen_mgmt_tx and if the wmi
command send fails, the corresponding mgmt frame is
not being dma unmapped.

Fix the missing dma unmapping of mgmt tx frame when
wmi command sending fails for mgmt tx by reference
via WMI. The already exisiting mgmt tx using copy by
value does not need such dma unmapping.
Add a separate wmi-tlv op for mgmt tx via ref, which
takes care of unmapping the dma address, in case of
wmi command sending failure.
Signed-off-by: NRakesh Pillai <pillair@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Update year for Qualcomm Atheros, Inc. copyrights.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Enable TDLS wider bandwidth support for 5GHz based on firmware wmi capabilities.

This patch is required for chipset QCA9888. Tested with firmware version
10.4-3.5.1-00018.
Signed-off-by: NBalaji Pothunoori <bpothuno@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

WCN3990 target uses 64 bit frags_paddr in htt tx descriptor,
which holds the physical address of SKB fragments in tx data path.

In order to support 64 bit bit frags_paddr in htt tx descriptor, define
htt_data_tx_desc_64 descriptor and ath10k_htt_tx_64 method for handling
tx data path with new descriptor fields.
Signed-off-by: NGovind Singh <govinds@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This reverts commit e937b8da.

Turns out that a new driver (mt76) is coming in through
Kalle's tree, and will conflict with this. It also has some
conflicting requirements, so we'll revisit this later.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Due to the limitation of wmi tlv parsing logic, if there are
two parameters in a wmi event with same tlv tag, we can get only
the last value, as it overwrites the prev value of the same tlv tag.

The service ready event in wcn3990 contains two parameters of the
same tag UINT32, due to which the svc bitmap is overwritten with the
DBS support parameter.

Refactor the service ready event parsing to allow parsing two tlv
of the same tag UINT32 for wcn3990.
Signed-off-by: NRakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: NGovind Singh <govinds@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.2.4 firmware branch (used in QCA988X) does not support
HTT_10_4_T2H_MSG_TYPE_PEER_STATS and that's why ath10k does not provide
tranmission rate statistics to user space, instead it just shows
hardcoded 6 Mbit/s. But pktlog firmware facility provides per peer tx
statistics. The firmware sends one pktlog event for every four
PPDUs per peer, which include:

* successful number of packets and bytes transmitted
* number of packets and bytes dropped
* retried number of packets and bytes
* rate info per ppdu

Firmware supports WMI_SERVICE_PEER_STATS, pktlog is enabled through
ATH10K_FLAG_PEER_STATS, which is nowadays enabled by default in ath10k.

This patch does not impact throughput.

Tested on QCA9880 with firmware version 10.2.4.70.48. This should also
work with firmware branch 10.2.4-1.0-00029

Parse peer stats from pktlog packets and update the tx rate information
per STA. This way user space can query about transmit rate with iw:

$iw wlan0 station dump
Station 3c:a9:f4:72:bb:a4 (on wlan1)
        inactive time:  8210 ms
        rx bytes:       9166
        rx packets:     44
        tx bytes:       1105
        tx packets:     9
        tx retries:     0
        tx failed:      1
        rx drop misc:   3
        signal:         -75 [-75, -87, -88] dBm
        signal avg:     -75 [-75, -85, -88] dBm
        tx bitrate:     39.0 MBit/s MCS 10
        rx bitrate:     26.0 MBit/s MCS 3
        rx duration:    23250 us
        authorized:     yes
        authenticated:  yes
        associated:     yes
        preamble:       short
        WMM/WME:        yes
        MFP:            no
        TDLS peer:      no
        DTIM period:    2
        beacon interval:100
        short preamble: yes
        short slot time:yes
        connected time: 22 seconds
Signed-off-by: NAnilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Remove CONFIG_MAC80211_DEBUGFS dependency on ath10k_sta_statistics().
ath10k_sta_statistics() has per sta tx/rx stats and this should not
be dependent on MAC80211_DEBUGFS.

No changes in functionality.
Signed-off-by: NAnilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Data packets are not sent by STA in case of STA joined to
non QOS AP (WMM disabled AP). This is happening because of STA
is sending data packets to firmware from host with qos enabled
along with non qos queue value(TID = 16).
Due to qos enabled, firmware is discarding the packet.

This patch fixes this issue by updating the qos based on station
WME capability field if WMM is disabled in AP.

This patch is required by 10.4 family chipsets like
QCA4019/QCA9888/QCA9884/QCA99X0.
Firmware Versoin : 10.4-3.5.1-00018.

For 10.2.4 family chipsets QCA988X/QCA9887 and QCA6174 this patch
has no effect.
Signed-off-by: NBalaji Pothunoori <bpothuno@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This adds an API to mac80211 to handle scheduling of TXQs and changes the
interface between driver and mac80211 for TXQ handling as follows:

- The wake_tx_queue callback interface no longer includes the TXQ. Instead,
  the driver is expected to retrieve that from ieee80211_next_txq()

- Two new mac80211 functions are added: ieee80211_next_txq() and
  ieee80211_schedule_txq(). The former returns the next TXQ that should be
  scheduled, and is how the driver gets a queue to pull packets from. The
  latter is called internally by mac80211 to start scheduling a queue, and
  the driver is supposed to call it to re-schedule the TXQ after it is
  finished pulling packets from it (unless the queue emptied).

The ath9k and ath10k drivers are changed to use the new API.
Signed-off-by: NToke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

It is required to update the teardown state of the peer when
a tdls link with that peer is terminated. This information is
useful for the target to perform some cleanups wrt the tdls peer.

Without proper cleanup, target assumes that the peer is connected and
blocks future connection requests, updating the teardown state of the
peer addresses the problem.

Tested this change on QCA9888 with 10.4-3.5.1-00018 fw version.
Signed-off-by: NManikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Commit 4ca18078 ("ath10k: disable wake_tx_queue for older devices")
disables the use of the mac80211 TXQs for some devices because of a theoretical
throughput regression. The original regression report[1] was related to
fq_codel qdisc drop performance, which was fixed in commit 9d18562a
("fq_codel: add batch ability to fq_codel_drop()"). Since then, we have not
seen the TXQ-related regression, so it should be safe to re-enable TXQs.

[1] http://lists.infradead.org/pipermail/ath10k/2016-April/007266.htmlSigned-off-by: NToke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Do not allow off channel operations like scans/roc when
there are active TDLS sessions.

The Current firmware 10.4-3.5.1-00035 on QCA9888 does not
supports any offchannel operations on active TDLS sessions,
either driver needs to block the offchannel operation requests
or should teardown the TDLS connection.
Signed-off-by: NAnilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To be able to use ath10k_mac_tdls_vif_stations_count() in
ath10k_hw_scan() in the following patch, move the functions
earlier in the file.

This commit is pure code move, no functional changes.
Signed-off-by: NAnilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA99x0 and QCA4019 family chips support CCMP-256, GCMP-128, and
GCMP-256 ciphers in hardware, so advertise support for these. As
firmware does not support group management frame ciphers (BIP),
handle them in software (mac80211).
Reviewed-by: NSebastian Gottschall <s.gottschall@dd-wrt.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently ath10k host enables power save support in station mode by
default for all firmwares but Power save for station mode still not supported
in some of the firmware versions. Which results in firmware crash while
issueing multiple scan commands.

Fix this problem by introducing new FW feature flag to check power save
support in firmware and then the firmware image can tell to ath10k that power
save mode is not supported in station mode.
Signed-off-by: NVenkateswara Naralasetty <vnaralas@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ACPI will rely on device driver to tell it if the device could support
wakeup function when system in D3 state.

This has caused some platform can't support remote wakeup correctly,
because the ACPI wakeup GPE is not enabled, hence registers the .set_wakeup
callback to handle it if device supports wakeup.

Tested with QCA6174 hw3.0, firmware ('WLAN.RM.4.4.1-00008-QCARMSWP-1')
Signed-off-by: NRyan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch adds the support of TDLS feature for 10.4 firmware
versions.

A new WMI service is added to advertise the support of TDLS for
10.4 firmwares.
Signed-off-by: NManikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix the following spelling mistakes in messages:
  syncronise -> synchronize
  unusally -> unusually
  addrress -> address
  inverval -> interval
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA9984 hardware can do 4x4 at 80Mhz, but only 2x2 at 160Mhz.

First, report this to user-space by setting the max-tx-speed
and max-rx-speed vht capabilities.

Second, if the peer rx-speed is configured, and if we
are in 160 or 80+80 mode, and the peer rx-speed matches
the max speed for 2x2 or 1x1 at 160Mhz (long guard interval),
then use that info to set the peer_bw_rxnss_override appropriately.

Without this, a 9984 firmware will not use 2x2 ratesets when
transmitting to peer (it will be stuck at 1x1), because
the firmware would not have configured the rxnss_override.
Signed-off-by: NBen Greear <greearb@candelatech.com>
[sven.eckelmann@openmesh.com: rebase, cleanup, drop 160Mhz workaround cleanup]
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
[kvalo@qca.qualcomm.com: use hw_params, rename the title]
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The ath10k firmware doesn't announce its VHT channel width capabilities in
the vht_cap information from the "service ready event" arguments. The
driver must therefore check whether the 160MHz short GI bit is set and
whether the driver still doesn't set the bits for the 160/80+80 MHz
capabilities.

The two bits for the channel width are a two bit integer and not two
separate bits which cannot be parsed without the knowledge of the other
bit. Using IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ (b10..) as a
mask for this task doesn't make any sense. The correct mask for the VHT
channel width should be used instead to make this check more readable.
Signed-off-by: NBen Greear <greearb@candelatech.com>
[sven.eckelmann@openmesh.com: separate 160Mhz workaround cleanup, add commit
 message]
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.

An spatch similar to the one for skb_put_zero() converts many
of the places using it:

    @@
    identifier p, p2;
    expression len, skb, data;
    type t, t2;
    @@
    (
    -p = skb_put(skb, len);
    +p = skb_put_data(skb, data, len);
    |
    -p = (t)skb_put(skb, len);
    +p = skb_put_data(skb, data, len);
    )
    (
    p2 = (t2)p;
    -memcpy(p2, data, len);
    |
    -memcpy(p, data, len);
    )

    @@
    type t, t2;
    identifier p, p2;
    expression skb, data;
    @@
    t *p;
    ...
    (
    -p = skb_put(skb, sizeof(t));
    +p = skb_put_data(skb, data, sizeof(t));
    |
    -p = (t *)skb_put(skb, sizeof(t));
    +p = skb_put_data(skb, data, sizeof(t));
    )
    (
    p2 = (t2)p;
    -memcpy(p2, data, sizeof(*p));
    |
    -memcpy(p, data, sizeof(*p));
    )

    @@
    expression skb, len, data;
    @@
    -memcpy(skb_put(skb, len), data, len);
    +skb_put_data(skb, data, len);

(again, manually post-processed to retain some comments)
Reviewed-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original idea is to limit the maximum TDLS peer link, but the logic
is always false, and never be able to restrict the number of TDLS peer
creation.

Fix the logic here and also move the checking earlier, so that it could
avoid to handle the failure case, e.g disable the tdls peer, delete the
peer and also vdev count cleanup.
Signed-off-by: NRyan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix output from checkpatch.pl like:
 Block comments use a trailing */ on a separate lin
Signed-off-by: NMarcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It seems set_coverage_class_work is not cancelled anywhere,
though I could not find a crash/warning  with this existing
design, its safer to cancel it during stop() and also before
restarting the hardware.
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If station advertises diffferent NSS capabilities in Rx_mcs set
of HT and VHT IEs in assoc req, the current NSS computation
logic configures the NSS support only based on Rx_mcs set of
HT capabilities in the driver. This is configuring the station
NSS capabilities incorreclty in the target.

For example, if station advertise Rx_mcs set as 2 spatial streams
in HT capabilities and 1 spatial streams in VHT capabilities in
assoc request, as per current logic we are calculating nss from
HT capabilities and the driver sets peer_num_spatial_streams as
2 for the station which is configured in VHT 1*1.

This patchs fix this issue by calculating the nss from VHT cap if
station supports vht.
Signed-off-by: NVenkateswara Rao Naralasetty <c_vnaral@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

I failed to notice that commit 523f6701 ("ath10k: update available channel
list for 5G radio") added two new warnings:

drivers/net/wireless/ath/ath10k/mac.c:3129:6: warning: symbol 'ath10k_mac_update_channel_list' was not declared. Should it be static?
drivers/net/wireless/ath/ath10k/mac.c:3170: Alignment should match open parenthesis

Fix those.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If a 5 GHz radio is calibrated for operation in both
the low band (channels 36 to 64) and high band(channels 100 to 169),
hardware allows operations in all the listed channels. However,
if the chip has been calibrated only for the low/high band and
a high/low band channel is configured, due to lack of calibration
there will be potentially invalid signal on those non calibrated channels.
To avoid this problem this patch sets IEEE80211_CHAN_DISABLED flag for
those non calibrated channels by using low_5ghz_chan and high_5ghz_chan
values which we get from target through wmi service ready event.

Driver initialized flags are getting re initialized in handle_channel
in cfg80211. So calling the function to disable the non supported channel
from reg_notifier().
Signed-off-by: NTamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Doing a channel switch via hostapd_cli seems to update
the new channel context for each VAP's appropriately as below
in 'ath10k_mac_update_vif_chan', hence we can safely suppress the
warning that shows up during this operation and dump the warning only
if no vaps are available for channel switch

hostapd_cli -i wlan0 chan_switch 5 5200
OK

ath10k_pci : mac chanctx switch n_vifs 3 mode 1
ath10k_pci : mac chanctx switch vdev_id 2 freq 5180->5200 width 0->0
ath10k_pci : mac chanctx switch vdev_id 1 freq 5180->5200 width 0->0
ath10k_pci : mac chanctx switch vdev_id 0 freq 5180->5200 width 0->0

Call Trace:

WARNING: backports-20161201-3.14.77-9ab3068/drivers/net/wireless/ath/ath10k/mac.c:7126
[<c022f2d4>] (warn_slowpath_null) from [<bf7f150c>]
(ath10k_reconfig_complete+0xe4/0x25c [ath10k_core])
[<bf7f150c>] (ath10k_reconfig_complete [ath10k_core])
[<bf7f35f0>] (ath10k_mac_vif_ap_csa_work+0x214/0x370 [ath10k_core])
[<bf7f38b8>] (ath10k_mac_op_change_chanctx+0x108/0x128 [ath10k_core])
[<bf782ac0>] (ieee80211_recalc_chanctx_min_def+0x30c/0x430 [mac80211])
[<bf7830a4>] (ieee80211_recalc_smps_chanctx+0x2ec/0x840 [mac80211])
[<bf7843e8>] (ieee80211_vif_use_reserved_context+0x7c/0xf8 [mac80211])
[<bf7843e8>] (ieee80211_vif_use_reserved_context [mac80211])
[<bf76e5d4>] (ieee80211_csa_finalize_work+0x5c/0x88 [mac80211])

Fixes: d7bf4b4a ("ath10k: fix ar->rx_channel updating logic")
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Set the NL80211_EXT_FEATURE_CQM_RSSI_LIST wiphy extended feature
wholesale in all mac80211-based drivers that do not set the
IEEE80211_VIF_BEACON_FILTER flags on their interfaces.  mac80211 will
be processing supplied RSSI values in ieee80211_rx_mgmt_beacon and
will detect when the thresholds set by
ieee80211_set_cqm_rssi_range_config are crossed.  Remaining (few)
drivers need code to enable the firmware to monitor the thresholds.
This is mostly only compile-tested.
Signed-off-by: NAndrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

it adds unnecessary level of indirection, while we just access structure
field
Signed-off-by: NAmadeusz Sławiński <amadeusz.slawinski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Station pointers are RCU protected so driver must
be extra careful if it tries to store them
internally for later use outside of the RCU
section it obtained it in.

It was possible for station teardown to race with
some htt events. The possible outcome could be a
use-after-free and a crash.

Only peer-flow-control capable firmware was
affected (so hardware-wise qca99x0 and qca4019).

This could be done in sta_state() itself via
explicit synchronize_net() call but there's
already a convenient sta_pre_rcu_remove() op that
can be hooked up to avoid extra rcu stall.

The peer->sta pointer itself can't be set to
NULL/ERR_PTR because it is later used in
sta_state() for extra sanity checks.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>