[ Upstream commit cc2278c413c3a06a93c23ee8722e4dd3d621de12 ]

When undergoing state transitions I/O might be requeued, hence
we should always call nvme_mpath_set_live() to schedule requeue_work
whenever the nvme device is live, independent on whether the
old state was live or not.
Signed-off-by: NMartin George <marting@netapp.com>
Signed-off-by: NGargi Srinivas <sring@netapp.com>
Signed-off-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit f7299d441a4da8a5088e651ea55023525a793a13 ]

If the call to of_gpiochip_scan_gpios() in of_gpiochip_add() fails, no
error handling is performed.  This lead to the need of callers to call
of_gpiochip_remove() on failure, which causes "BAD of_node_put() on ..."
if the failure happened before the call to of_node_get().

Fix this by adding proper error handling.

Note that calling gpiochip_remove_pin_ranges() multiple times causes no
harm: subsequent calls are a no-op.

Fixes: dfbd379b ("gpio: of: Return error if gpio hog configuration failed")
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NMukesh Ojha <mojha@codeaurora.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit dd08a8d9a66de4b54575c294a92630299f7e0fe7 ]

When CONFIG_VMAP_STACK=y, __pa() returns incorrect physical address for
a stack virtual address. Stack DMA buffers must be avoided.
Signed-off-by: Nraymond pang <raymondpangxd@gmail.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 92c77f7c4d5dfaaf45b2ce19360e69977c264766 ]

valid_phys_addr_range() is used to sanity check the physical address range
of an operation, e.g., access to /dev/mem. It uses __pa(high_memory)
internally.

If memory is populated at the end of the physical address space, then
__pa(high_memory) is outside of the physical address space because:

   high_memory = (void *)__va(max_pfn * PAGE_SIZE - 1) + 1;

For the comparison in valid_phys_addr_range() this is not an issue, but if
CONFIG_DEBUG_VIRTUAL is enabled, __pa() maps to __phys_addr(), which
verifies that the resulting physical address is within the valid physical
address space of the CPU. So in the case that memory is populated at the
end of the physical address space, this is not true and triggers a
VIRTUAL_BUG_ON().

Use __pa(high_memory - 1) to prevent the conversion from going beyond
the end of valid physical addresses.

Fixes: be62a320 ("x86/mm: Limit mmap() of /dev/mem to valid physical addresses")
Signed-off-by: NRalph Campbell <rcampbell@nvidia.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Craig Bergstrom <craigb@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Sean Young <sean@mess.org>

Link: https://lkml.kernel.org/r/20190326001817.15413-2-rcampbell@nvidia.comSigned-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit c8206579175c34a2546de8a74262456278a7795a ]

If an incoming ELS of type RSCN contains more than one element, zfcp
suboptimally causes repeated erp trigger NOP trace records for each
previously failed port. These could be ports that went away.  It loops over
each RSCN element, and for each of those in an inner loop over all
zfcp_ports.

The trigger to recover failed ports should be just the reception of some
RSCN, no matter how many elements it has. So we can loop over failed ports
separately, and only then loop over each RSCN element to handle the
non-failed ports.

The call chain was:

  zfcp_fc_incoming_rscn
    for (i = 1; i < no_entries; i++)
      _zfcp_fc_incoming_rscn
        list_for_each_entry(port, &adapter->port_list, list)
          if (masked port->d_id match) zfcp_fc_test_link
          if (!port->d_id) zfcp_erp_port_reopen "fcrscn1"   <===

In order the reduce the "flooding" of the REC trace area in such cases, we
factor out handling the failed ports to be outside of the entries loop:

  zfcp_fc_incoming_rscn
    if (no_entries > 1)                                     <===
      list_for_each_entry(port, &adapter->port_list, list)  <===
        if (!port->d_id) zfcp_erp_port_reopen "fcrscn1"     <===
    for (i = 1; i < no_entries; i++)
      _zfcp_fc_incoming_rscn
        list_for_each_entry(port, &adapter->port_list, list)
          if (masked port->d_id match) zfcp_fc_test_link

Abbreviated example trace records before this code change:

Tag            : fcrscn1
WWPN           : 0x500507630310d327
ERP want       : 0x02
ERP need       : 0x02

Tag            : fcrscn1
WWPN           : 0x500507630310d327
ERP want       : 0x02
ERP need       : 0x00                 NOP => superfluous trace record

The last trace entry repeats if there are more than 2 RSCN elements.
Signed-off-by: NSteffen Maier <maier@linux.ibm.com>
Reviewed-by: NBenjamin Block <bblock@linux.ibm.com>
Reviewed-by: NJens Remus <jremus@linux.ibm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit daf5cc27eed99afdea8d96e71b89ba41f5406ef6 ]

free the symlink body after the same RCU delay we have for freeing the
struct inode itself, so that traversal during RCU pathwalk wouldn't step
into freed memory.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Reviewed-by: NJeff Layton <jlayton@kernel.org>
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit f276e002793cdb820862e8ea8f76769d56bba575 ]

if platform_driver_register fails, cleanup the allocated resource
gracefully.
Signed-off-by: NMukesh Ojha <mojha@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit b929a500d68479163c48739d809cbf4c1335db6f ]

Since commit

  ad67b74d ("printk: hash addresses printed with %p")

at boot "____ptrval____" is printed instead of the trampoline addresses:

  Base memory trampoline at [(____ptrval____)] 99000 size 24576

Remove the print as we don't want to leak kernel addresses and this
statement is not needed anymore.

Fixes: ad67b74d ("printk: hash addresses printed with %p")
Signed-off-by: NMatteo Croce <mcroce@redhat.com>
Signed-off-by: NBorislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190326203046.20787-1-mcroce@redhat.comSigned-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 4cb6560514fa19d556954b88128f3846fee66a03 ]

Renaming a netdev-trigger-tracked interface was resulting in an
unbalanced dev_hold().

Example:
> iw phy phy0 interface add foo type __ap
> echo netdev > trigger
> echo foo > device_name
> ip link set foo name bar
> iw dev bar del
[  237.355366] unregister_netdevice: waiting for bar to become free. Usage count = 1
[  247.435362] unregister_netdevice: waiting for bar to become free. Usage count = 1
[  257.545366] unregister_netdevice: waiting for bar to become free. Usage count = 1

Above problem was caused by trigger checking a dev->name which obviously
changes after renaming an interface. It meant missing all further events
including the NETDEV_UNREGISTER which is required for calling dev_put().

This change fixes that by:
1) Comparing device struct *address* for notification-filtering purposes
2) Dropping unneeded NETDEV_CHANGENAME code (no behavior change)

Fixes: 06f502f5 ("leds: trigger: Introduce a NETDEV trigger")
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 41f00e6e9e55546390031996b773e7f3c1d95928 ]

of_match_device in usb251xb_probe can fail and returns a NULL pointer.
The patch avoids a potential NULL pointer dereference in this scenario.
Signed-off-by: NAditya Pakki <pakki001@umn.edu>
Reviewed-by: NRichard Leitner <richard.leitner@skidata.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit fba1bdd2a9a93f3e2181ec1936a3c2f6b37e7ed6 ]

In case iscsi_lookup_endpoint fails, the fix returns -EINVAL to avoid NULL
pointer dereference.
Signed-off-by: NKangjie Lu <kjlu@umn.edu>
Acked-by: NManish Rangankar <mrangankar@marvell.com>
Reviewed-by: NMukesh Ojha <mojha@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit b6554cfe09e1f610aed7d57164ab7760be57acd9 ]

There are a few windows during AER/EEH when we can access PCIe I/O mapped
registers. This will harden the access to insure we do not allow PCIe
access during errors
Signed-off-by: NDave Carroll <david.carroll@microsemi.com>
Reviewed-by: NSagar Biradar <sagar.biradar@microchip.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit c2fe742ff6e77c5b4fe4ad273191ddf28fdea25e ]

During expander reset handling, the driver invokes kernel function
scsi_host_find_tag() to obtain outstanding requests associated with the
scsi host managed by the driver. Driver loops from tag value zero to hba
queue depth to obtain the outstanding scmds. But when blk-mq is enabled,
the block layer may return stale entry for one or more requests. This may
lead to kernel panic if the returned value is inaccessible or the memory
pointed by the returned value is reused.

Reference of upstream discussion:

	https://patchwork.kernel.org/patch/10734933/

Instead of calling scsi_host_find_tag() API for each and every smid (smid
is tag +1) from one to shost->can_queue, now driver will call this API (to
obtain the outstanding scmd) only for those smid's which are outstanding at
the driver level.

Driver will determine whether this smid is outstanding at driver level by
looking into it's corresponding MPI request frame, if its MPI request frame
is empty, then it means that this smid is free and does not need to call
scsi_host_find_tag() for it.  By doing this, driver will invoke
scsi_host_find_tag() for only those tags which are outstanding at the
driver level.

Driver will check whether particular MPI request frame is empty or not by
looking into the "DevHandle" field. If this field is zero then it means
that this MPI request is empty. For active MPI request DevHandle must be
non-zero.

Also driver will memset the MPI request frame once the corresponding scmd
is processed (i.e. just before calling
scmd->done function).
Signed-off-by: NSreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 2dbed152e2d4c3fe2442284918d14797898b1e8a ]

allnoconfig build with just ARCH_DAVINCI enabled
fails because drivers/clk/davinci/* depends on
REGMAP being enabled.

Fix it by selecting REGMAP_MMIO when building in
DaVinci support.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Reviewed-by: NDavid Lechner <david@lechnology.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 2d8f92897ad816f5dda54b2ed2fd9f2d7cb1abde ]

meson_drv_unbind() doesn't unregister the IRQ handler, which can lead to
use-after-free if the IRQ fires after unbind:

[   64.656876] Unable to handle kernel paging request at virtual address ffff000011706dbc
...
[   64.662001] pc : meson_irq+0x18/0x30 [meson_drm]

I'm assuming that a similar problem could happen on the error path of
bind(), so uninstall the IRQ handler there as well.

Fixes: bbbe775e ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: NJean-Philippe Brucker <jean-philippe.brucker@arm.com>
Acked-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322152657.13752-2-jean-philippe.brucker@arm.comSigned-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 776e78677f514ecddd12dba48b9040958999bd5a ]

meson_drv_bind() registers a meson_drm struct as the device's privdata,
but meson_drv_unbind() tries to retrieve a drm_device. This may cause a
segfault on shutdown:

[ 5194.593429] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000197
 ...
[ 5194.788850] Call trace:
[ 5194.791349]  drm_dev_unregister+0x1c/0x118 [drm]
[ 5194.795848]  meson_drv_unbind+0x50/0x78 [meson_drm]

Retrieve the right pointer in meson_drv_unbind().

Fixes: bbbe775e ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: NJean-Philippe Brucker <jean-philippe.brucker@arm.com>
Acked-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322152657.13752-1-jean-philippe.brucker@arm.comSigned-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 6cf4511e9729c00a7306cf94085f9cc3c52ee723 ]

In case devm_kzalloc, the patch returns ENOMEM to avoid potential
NULL pointer dereference.
Signed-off-by: NKangjie Lu <kjlu@umn.edu>
Reviewed-by: NAndrew Jeffery <andrew@aj.id.au>
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 3f04e0a6cfebf48152ac64502346cdc258811f79 ]

If userspace has open fd(s) when drm_dev_unplug() is run, it will result
in drm_dev_unregister() being called twice. First in drm_dev_unplug() and
then later in drm_release() through the call to drm_put_dev().

Since userspace already holds a ref on drm_device through the drm_minor,
it's not necessary to add extra ref counting based on no open file
handles. Instead just drm_dev_put() unconditionally in drm_dev_unplug().

We now have this:
- Userpace holds a ref on drm_device as long as there's open fd(s)
- The driver holds a ref on drm_device as long as it's bound to the
  struct device

When both sides are done with drm_device, it is released.
Signed-off-by: NNoralf Trønnes <noralf@tronnes.org>
Reviewed-by: NOleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NSean Paul <sean@poorly.run>
Signed-off-by: NDave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208140103.28919-2-noralf@tronnes.orgSigned-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 75eac7b5f68b0a0671e795ac636457ee27cc11d8 ]

The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.

Detected by coccinelle with the following warnings:
./drivers/net/ethernet/ti/netcp_ethss.c:3661:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3654, but without a corresponding object release within this function.
./drivers/net/ethernet/ti/netcp_ethss.c:3665:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3654, but without a corresponding object release within this function.
Signed-off-by: NWen Yang <wen.yang99@zte.com.cn>
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit be693df3cf9dd113ff1d2c0d8150199efdba37f6 ]

The call to ehea_get_eth_dn returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.

Detected by coccinelle with the following warnings:
./drivers/net/ethernet/ibm/ehea/ehea_main.c:3163:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3154, but without a corresponding object release within this function.
Signed-off-by: NWen Yang <wen.yang99@zte.com.cn>
Cc: Douglas Miller <dougmill@linux.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit fa3a419d2f674b431d38748cb58fb7da17ee8949 ]

The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.

Detected by coccinelle with the following warnings:
./drivers/net/ethernet/xilinx/xilinx_axienet_main.c:1624:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1569, but without a corresponding object release within this function.
Signed-off-by: NWen Yang <wen.yang99@zte.com.cn>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Cc: John Linn <John.Linn@xilinx.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 5a698243930c441afccec04e4d5dc8febfd2b775 ]

Specifying a retrans=0 mount parameter to a NFS/TCP mount, is
inadvertently causing the NFS client to rewrite any specified
timeout parameter to the default of 60 seconds.

Fixes: a956beda ("NFS: Allow the mount option retrans=0")
Signed-off-by: NTrond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 7cf77b273a8fc51e7de622fa6691abd4436a9a6b ]
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 41b37f4c0fa67185691bcbd30201cad566f2f0d1 ]

This patch fixes a spelling typo.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Fixes: cc42603d ("ARM: dts: imx6q-icore-rqs: Add Engicam IMX6 Q7 initial support")
Signed-off-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit fe384e2fa36ca084a456fd30558cccc75b4b3fbd ]

callers of tcf_gact_goto_chain_index() can potentially read an old value
of the chain index, or even dereference a NULL 'goto_chain' pointer,
because 'goto_chain' and 'tcfa_action' are read in the traffic path
without caring of concurrent write in the control path. The most recent
value of chain index can be read also from a->tcfa_action (it's encoded
there together with TC_ACT_GOTO_CHAIN bits), so we don't really need to
dereference 'goto_chain': just read the chain id from the control action.

Fixes: e457d86a ("net: sched: add couple of goto_chain helpers")
Signed-off-by: NDavide Caratti <dcaratti@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit cd5afa91f078c0787be0a62b5ef90301c00b0271 ]

Both PCLK and HCLK are "required" clocks according to macb devicetree
documentation. There is a chance that devm_clk_get doesn't return a
negative error but just a NULL clock structure instead. In such a case
the driver proceeds as usual and uses pclk value 0 to calculate MDC
divisor which is incorrect. Hence fix the same in clock initialization.
Signed-off-by: NHarini Katakam <harini.katakam@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 6a8ca24590a2136921439b376c926c11a6effc0e ]

phydm.internal is allocated using kzalloc which is used multiple
times without a check for NULL pointer. This patch avoids such a
scenario by returning 0, consistent with the failure case.
Signed-off-by: NAditya Pakki <pakki001@umn.edu>
Reviewed-by: NMukesh Ojha <mojha@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 22c971db7dd4b0ad8dd88e99c407f7a1f4231a2e ]

Colin King reported a bug in read_bbreg_hdl():

	memcpy(pcmd->rsp, (u8 *)&val, pcmd->rspsz);

The problem is that "val" is uninitialized.

This code is obviously not useful, but so far as I can tell
"pcmd->cmdcode" is never GEN_CMD_CODE(_Read_BBREG) so it's not harmful
either.  For now the easiest fix is to just call r8712_free_cmd_obj()
and return.

Fixes: 2865d42c ("staging: r8712u: Add the new driver to the mainline kernel")
Reported-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit d70d70aec9632679dd00dcc1b1e8b2517e2c7da0 ]

skb allocated via dev_alloc_skb can fail and return a NULL pointer.
This patch avoids such a scenario and returns, consistent with other
invocations.
Signed-off-by: NAditya Pakki <pakki001@umn.edu>
Reviewed-by: NMukesh Ojha <mojha@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 7671ce0d92933762f469266daf43bd34d422d58c ]

hwxmits is allocated via kcalloc and not checked for failure before its
dereference. The patch fixes this problem by returning error upstream
in rtl8723bs, rtl8188eu.
Signed-off-by: NAditya Pakki <pakki001@umn.edu>
Acked-by: NMukesh Ojha <mojha@codeaurora.org>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 9624bafa5f6418b9ca5b3f66d1f6a6a2e8bf6d4c ]

The ks8851 chip's initial carrier state is down. A Link Change Interrupt
is signaled once interrupts are enabled if the carrier is up.

The ks8851 driver has it backwards by assuming that the initial carrier
state is up. The state is therefore misrepresented if the interface is
opened with no cable attached. Fix it.

The Link Change interrupt is sometimes not signaled unless the P1MBSR
register (which contains the Link Status bit) is read on ->ndo_open().
This might be a hardware erratum. Read the register by calling
mii_check_link(), which has the desirable side effect of setting the
carrier state to down if the cable was detached while the interface was
closed.
Signed-off-by: NLukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit d268f31552794abf5b6aa5af31021643411f25f5 ]

The ks8851 driver currently requests the IRQ before registering the
net_device.  Because the net_device name is used as IRQ name and is
still "eth%d" when the IRQ is requested, it's impossibe to tell IRQs
apart if multiple ks8851 chips are present.  Most other drivers delay
requesting the IRQ until the net_device is opened.  Do the same.

The driver doesn't enable interrupts on the chip before opening the
net_device and disables them when closing it, so there doesn't seem to
be a need to request the IRQ already on probe.
Signed-off-by: NLukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 761cfa979a0c177d6c2d93ef5585cd79ae49a7d5 ]

Commit 73fdeb82 ("net: ks8851: Add optional vdd_io regulator and
reset gpio") amended the ks8851 driver to briefly assert the chip's
reset pin on probe. It also amended the probe routine's error path to
reassert the reset pin if a subsequent initialization step fails.

However the commit misplaced reassertion of the reset pin in the error
path such that it is not performed if the check of the Chip ID and
Enable Register (CIDER) fails. The error path is therefore slightly
asymmetrical to the probe routine's body. Fix it.
Signed-off-by: NLukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 536d3680fd2dab5c39857d62a3e084198fc74ff9 ]

The ks8851 driver lets the chip auto-dequeue received packets once they
have been read in full. It achieves that by setting the ADRFE flag in
the RXQCR register ("Auto-Dequeue RXQ Frame Enable").

However if allocation of a packet's socket buffer or retrieval of the
packet over the SPI bus fails, the packet will not have been read in
full and is not auto-dequeued. Such partial retrieval of a packet
confuses the chip's RX queue management:  On the next RX interrupt,
the first packet read from the queue will be the one left there
previously and this one can be retrieved without issues. But for any
newly received packets, the frame header status and byte count registers
(RXFHSR and RXFHBCR) contain bogus values, preventing their retrieval.

The chip allows explicitly dequeueing a packet from the RX queue by
setting the RRXEF flag in the RXQCR register ("Release RX Error Frame").
This could be used to dequeue the packet in case of an error, but if
that error is a failed SPI transfer, it is unknown if the packet was
transferred in full and was auto-dequeued or if it was only transferred
in part and requires an explicit dequeue. The safest approach is thus
to always dequeue packets explicitly and forgo auto-dequeueing.

Without this change, I've witnessed packet retrieval break completely
when an SPI DMA transfer fails, requiring a chip reset. Explicit
dequeueing magically fixes this and makes packet retrieval absolutely
robust for me.

The chip's documentation suggests auto-dequeuing and uses the RRXEF
flag only to dequeue error frames which the driver doesn't want to
retrieve. But that seems to be a fair-weather approach.
Signed-off-by: NLukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 5cd1c56c42beb6d228cc8d4373fdc5f5ec78a5ad ]

Add PCI ID for Intel Comet Lake PCH.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 032f85c9360fb1a08385c584c2c4ed114b33c260 ]

Increase the reset duration to ensure correct phy functionality. The
reset duration is taken from barebox commit 52fdd510de ("ARM: dts:
pfla02: use long enough reset for ethernet phy"):

  Use a longer reset time for ethernet phy Micrel KSZ9031RNX. Otherwise a
  small percentage of modules have 'transmission timeouts' errors like

  barebox@Phytec phyFLEX-i.MX6 Quad Carrier-Board:/ ifup eth0
  warning: No MAC address set. Using random address 7e:94:4d:02:f8:f3
  eth0: 1000Mbps full duplex link detected
  eth0: transmission timeout
  T eth0: transmission timeout
  T eth0: transmission timeout
  T eth0: transmission timeout
  T eth0: transmission timeout

Cc: Stefan Christ <s.christ@phytec.de>
Cc: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: NMarco Felsch <m.felsch@pengutronix.de>
Fixes: 3180f956 ("ARM: dts: Phytec imx6q pfla02 and pbab01 support")
Signed-off-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 091dacc3cc10979ab0422f0a9f7fcc27eee97e69 ]

Restore the status of ep->stopped in function net2272_dequeue().

When the given request is not found in the endpoint queue
the function returns -EINVAL without restoring the state of
ep->stopped. Thus the endpoint keeps blocked and does not transfer
any data anymore.

This fix is only compile-tested, since we do not have a
corresponding hardware. An analogous fix was tested in the sibling
driver. See "usb: gadget: net2280: Fix net2280_dequeue()"
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGuido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit f1d3fba17cd4eeea20397f1324b7b9c69a6a935c ]

When a request must be dequeued with net2280_dequeue() e.g. due
to a device clear action and the same request is finished by the
function scan_dma_completions() then the function net2280_dequeue()
does not find the request in the following search loop and
returns the error -EINVAL without restoring the status ep->stopped.
Thus the endpoint keeps blocked and does not receive any data
anymore.
This fix restores the status and does not issue an error message.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGuido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 9d6a54c1430647355a5e23434881b2ca3d192b48 ]

The OUT endpoint normally blocks (NAK) subsequent packets when a
short packet was received and returns an incomplete queue entry to
the gadget driver. Thereby the gadget driver can detect a short packet
when reading queue entries with a length that is not equal to a
multiple of packet size.

The start_queue() function enables receiving OUT packets regardless of
the content of the OUT FIFO. This results in a race: With the current
code, it's possible that the "!ep->is_in && (readl(&ep->regs->ep_stat)
& BIT(NAK_OUT_PACKETS))" test in start_dma() will fail, then a short
packet will be received, and then start_queue() will call
stop_out_naking(). That's what we don't want (OUT naking gets turned
off while there is data in the FIFO) because then the next driver
request might receive a mixture of old and new packets.

With the patch, this race can't occur because the FIFO's state is
tested after we know that OUT naking is already turned on, and OUT
naking is stopped only when both of the conditions are met.  This
ensures that all received data is delivered to the gadget driver,
which can detect a short packet now before new packets are appended
to the last short packet.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGuido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 7ae622c978db6b2e28b4fced6ecd2a174492059d ]

This patch simply adds a new PCI Device ID
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>