Handle memory allocation failures when reading packets.

We have to read something from the host, even if we can't allocate any
memory.  If we don't, the host side of the device may fill up and stop
delivering interrupts because no new packets can be queued.

A single sk_buff is allocated whenever an MTU is seen which is larger
than any seen earlier.  This is used to read packets if there is a
memory allocation failure.

The large MTU check is done from eth_configure, which is called when a
interface is added to the system.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A bunch of MTU-related cleanups in the network code.

First, there is the addition of the notion of a maximally-sized packet, which
is the MTU plus headers.  This is used to size the skb that will receive a
packet.  This allows ether_adjust_skb to go away, as it was used to resize the
skb after it was allocated.

Since the skb passed into the low-level read routine is no longer resized, and
possibly reallocated, there, they (and the write routines) don't need to get
an sk_buff **.  They just need the sk_buff * now.  The callers of
ether_adjust_skb still need to do the skb_put, so that's now inlined.

The MAX_PACKET definitions in most of the drivers are gone.

The set_mtu methods were all the same and did nothing, so they can be
removed.

The ethertap driver had a typo which doubled the size of the packet rather
than adding two bytes to it.  It also wasn't defining its setup_size, causing
a zero-byte kmalloc and crash when the invalid pointer returned from kmalloc
was dereferenced.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Style and other non-functional changes in the UML networking code, including
	include tidying
	style violations
	copyright updates
	printks getting severities
	userspace code calling libc directly rather than using the os_*
wrappers

There's also a exit path cleanup in the pcap driver.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There are various uses of powers of 1000, plus the odd BILLION constant in the
time code.  However, there are perfectly good definitions of *SEC_PER_*SEC in
linux/time.h which can be used instaed.

These are replaced directly in kernel code.  Userspace code imports those
constants as UM_*SEC_PER_*SEC and uses these.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now that ITIMER_REAL is no longer used, there is no need for any use of
SIGALRM whatsoever.  This patch removes all mention of it.

In addition, real_alarm_handler took a signal argument which is now always
SIGVTALRM.  So, that is gone.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Put back an implementation of timeval_to_ns in arch/um/os-Linux/time.c.
tglx pointed out in his review of tickless support that there was a
perfectly good implementation of it in linux/time.h.  The problem is that
this is userspace code which can't pull in kernel headers and there doesn't
seem to be a libc version.

So, I'm copying the version from linux/time.h rather than resurrecting my
version.  This causes some declaration changes as it now returns a signed
value rather than an unsigned value.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now, the idle loop now longer needs SIGALRM firing - it can just sleep for the
requisite amount of time and fake a timer interrupt when it finishes.

Any use of ITIMER_REAL now goes away.  disable_timer only turns off
ITIMER_VIRTUAL.  switch_timers is no longer needed, so it, and all calls, goes
away.

disable_timer now returns the amount of time remaining on the timer.
default_idle uses this to tell idle_sleep how long to sleep.  idle_sleep will
call alarm_handler if nanosleep returns 0, which is the case if it didn't
return early due to an interrupt.  Otherwise, it just returns.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Enable tickless support.

CONFIG_TICK_ONESHOT and CONFIG_NO_HZ are enabled.

itimer_clockevent gets CLOCK_EVT_FEAT_ONESHOT and an implementation of
.set_next_event.

CONFIG_UML_REAL_TIME_CLOCK goes away because it only makes sense when there is
a clock ticking away all the time.  timer_handler now just calls do_IRQ once
without trying to figure out how many ticks to emulate.

The idle loop now needs to turn ticking on and off.

Userspace ticks keep happening as usual.  However, the userspace loop keep
track of when the next wakeup should happen and suppresses process ticks until
that happens.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add clocksource support.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Enable CONFIG_GENERIC_CLOCKEVENTS.

timer_irq gets its name changed to timer_handler, and becomes the recipient of
timer signals.

The clock_event_device is set up to imitate the current ticking clock, i.e.
CLOCK_EVT_FEAT_ONESHOT is not enabled yet.

disable_timer now doesn't ignore SIGALRM and SIGVTALRM because that breaks
delay calibration.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Enable CONFIG_GENERIC_TIME.

As a side-effect of this, the UML implementations of do_gettimeofday and
do_settimeofday go away, as these are provided by generic code.  set_time also
goes away since it was only used by do_settimeofday.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move timer signal initialization from init_irq_signals to a new function,
timer_init.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

set_interval took a timer type as an argument, but it always specified a
virtual timer.  So, it is not needed, and it is gone, and set_interval is
simplified appropriately.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix up the switching between virtual and real timers.  The idle loop sleeps,
so the timer at that point must be real time.  At all other times, the timer
must be virtual.  Even when userspace is running, and the kernel is asleep,
the virtual timer is correct because the process timer will be running and the
process timer will be firing.

The timer switch used to be in the context switch and timer handler code.
This is moved to the idle loop and the signal handler, making it much more
clear why it is happening.

switch_timers now returns the old timer type so that it may be restored.  The
signal handler uses this in order to restore the previous timer type when it
returns.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Eliminate hz() since its only purpose was to provide a kernel-space constant
to userspace code.  This can be done instead by providing the constant
directly through kernel_constants.h.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make mconsole parameter parsing slightly more idiomatic.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

arch/um/os-Linux/tt.c is no longer used.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

vmalloc() returns a void pointer, so casting to (void *) is pretty pointless.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The floating point fields in the pt_regs register file aren't used, so they
are deleted.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Tidy the code affected by the floating point fixes.

A bunch of unused stuff is gone, including two sigcontext.c files,
which turned out to be entirely unneeded.

There are the usual fixes -
	whitespace and style cleanups
	copyright updates
	emacs formatting comments gone
	include cleanups
	adding severities to printks
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the passing of printk output back to the mconsole client.  The existing
code was somewhat confused, accumulating output in a buffer, but writing it
out entirely whenever a new chunk was added.  This is fixed.

The earlier include cleanups caused linux/sysrq.h to not be included - this is
fixed by adding the include back, under CONFIG_MAGIC_SYSRQ.

CONFIG_MAGIC_SYSRQ is also defaulted to on in defconfig.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix core dumping of floating point state.  ELF_CORE_COPY_FPREGS gets a
definitions, and as a result, dump_fpu no longer needs to exist.  Also,
elf_fpregset_t needed a real definition.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Handle floating point state better in ptrace.  The code now correctly
distinguishes between PTRACE_[GS]ETFPREGS and PTRACE_[GS]ETFPXREGS.  The FPX
requests get handed off to arch-specific code because that's not generic.

get_fpregs, set_fpregs, set_fpregs, and set_fpxregs needed real
implementations.

Something here exposed a missing include in asm/page.h, which needed
linux/types.h in order to get gfp_t, so that's fixed here.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Handle floating point state in across signals correctly.  UML/i386 needs to
know whether the host does PTRACE_[GS]ETFPXREGS, so an arch_init_registers
hook is added, which on x86_64 does nothing.

UML doesn't save and restore floating point registers on kernel entry and
exit, so they need to be copied between the host process and the sigcontext.
save_fpx_registers and restore_fpx_registers are added for this purpose.
save_fp_registers and restore_fp_registers already exist.

There was a bunch of floating point state conversion code in
arch/um/sys-i386/ptrace.c which isn't needed there, but is needed in signal.c,
so it is moved over.

The i386 code now distinguishes between fp and fpx state and handles them
correctly.  The x86_64 code just needs to copy state as-is between the host
process and the stack.  There are also some fixes there to pass the correct
address of the floating point state around.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Stop including asm/user.h from libc - it seems to be disappearing from
distros.  It's replaced with sys/user.h which defines user_fpregs_struct and
user_fpxregs_struct instead of user_i387_struct and struct user_fxsr_struct on
i386.

As a bonus, on x86_64, I get to dump some stupid typedefs which were needed in
order to get asm/user.h to compile.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Style fixes in hostfs.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Get rid of an empty if statement which might look like a bug to a
casual reader.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Tidy the tlb flushing code.

With tt mode gone, there is no reason to have the capability to have
called directly from do_mmap, do_mprotect, and do_munmap, rather than
calling a function pointer that it is given.

There was a large amount of data that was passed from function to
function, being used at the lowest level, without being changed.  This
stuff is now encapsulated in a structure which is initialized at the
top layer and passed down.  This simplifies the code, reduces the
amount of code needed to pass the parameters around, and saves on
stack space.

A somewhat more subtle change is the meaning of the current operation
index.  It used to start at -1, being pre-incremented when adding an
operation.  It now starts at 0, being post-incremented, with
associated adjustments of +/- 1 on comparisons.

In addition, tlb.h contained a couple of declarations which had no
users outside of tlb.c, so they could be moved or deleted.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A number of files that were changed in the recent removal of tt mode
are userspace files which call the os_* wrappers instead of calling
libc directly.  A few other files were affected by this, through

This patch makes these call glibc directly.

There are also style fixes in the affected areas.

os_print_error has no remaining callers, so it is deleted.

There is a interface change to os_set_exec_close, eliminating a
parameter which was always the same.  The callers are fixed as well.

os_process_pc got its error path cleaned up.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

"extern inline" will have different semantics with gcc 4.3.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert the boot-time host ptrace testing from clone to fork.  They were
essentially doing fork anyway.  This cleans up the code a bit, and makes
valgrind a bit happier about grinding it.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes some userspace files which were calling libc through the os_*
wrappers.

It turns out that there was only one user of os_new_tty_pgrp, so it can be
deleted.

There are also some style and whitespace fixes in here.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The space allocated for a process LDT wasn't being freed when the process
exited.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Before the removal of tt mode, access to a register on the skas-mode side of a
pt_regs struct looked like pt_regs.regs.skas.regs.regs[FOO].  This was bad
enough, but it became pt_regs.regs.regs.regs[FOO] with the removal of the
union from the middle.  To get rid of the run of three "regs", the last field
is renamed to "gp".
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch folds mmu_context_skas into struct mm_context, changing all users
of these structures as needed.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

do_longjmp used to be needed when UML didn't have its own implementation of
setjmp and longjmp.  They came from libc, and couldn't be called directly from
kernel code, as the libc jmp_buf couldn't be imported there.  do_longjmp was a
userspace function which served to provide longjmp access to kernel code.

This is gone, and a number of void * pointers can now be jmp_buf *.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Eliminate some uses of __u64 in the physical memory support.  It's hard to get
a definition of __u64 in both kernel and userspace code on x86_64, so this
changes them to unsigned long long.

There are also a copyright update and formatting comment removal from the
affected header.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Formatting changes in the files which have been changed in the course
of folding foo_skas functions into their callers.  These include:
	copyright updates
	header file trimming
	style fixes
	adding severity to printks

These changes should be entirely non-functional.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch makes a number of simplifications enabled by the removal of
CHOOSE_MODE.  There were lots of functions that looked like

	int foo(args){
		foo_skas(args);
	}

The bodies of foo_skas are now folded into foo, and their declarations (and
sometimes entire header files) are deleted.

In addition, the union uml_pt_regs, which was a union between the tt and skas
register formats, is now a struct, with the tt-mode arm of the union being
removed.

It turns out that usr2_handler was unused, so it is gone.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Formatting changes in the files which have been changed in the course
of removing CHOOSE_MODE.  These include:
	copyright updates
	header file trimming
	style fixes
	adding severity to printks

These changes should be entirely non-functional.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>