Set gadget device state as configurated after set configuration
has finished.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

By adding COMPILE_TEST to the list of dependencies
we can build test this driver on all other architectures
which is very valuable for maintainers applying patches
and to find silly mistakes during development.
Reviewed-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove that single instance of writel_relaxed()
call which is only available on ARM architecture.

This will let us build test this driver on all
different architectures.
Reviewed-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this solves the following build warning found when
running compile tests.

drivers/usb/phy/phy-msm-usb.c: In function ‘msm_otg_read_dt’:
drivers/usb/phy/phy-msm-usb.c:1459:20: warning: cast from pointer \
	to integer of different size [-Wpointer-to-int-cast]
  pdata->phy_type = (int) id->data;
                    ^
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There could be more than one USB2.0 PHY's on the platform.
This will allow all of them to be registered successfully.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

New platform uses RBCPR hardware feature, with that voting for
absolute voltage of VDD CX is not required. Hence vote for corner of
VDD CX which uses nominal corner voltage on VDD CX.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Cc: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Put the transceiver in non-driving mode. Otherwise host
may not detect soft-disconnection.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Cc: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Select the secondary PHY using the TCSR register, if phy-num=1
in the DTS (or phy_number is set in the platform data).  The
SOC has 2 PHYs which can be used with the OTG port, and this
code allows configuring the correct one.

Note: This resolves the problem I was seeing where I couldn't
get the USB driver working at all on a dragonboard, from cold
boot.  This patch depends on patch 5/14 from Ivan's msm USB
patch set.  It does not use DT for the register address, as
there's no evidence that this address changes between SoC
versions.
Signed-off-by: NTim Bird <tim.bird@sonymobile.com>
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix the value used for Parallel Transceiver Select (PTS) for the MSM USB
controller.  This is a standard chipidea PORTSC definition, where
a PHY_TYPE of 10b (<<30) is ULPI and 11b (<<30) is SERIAL.
Fix the definitions and use them correctly in the driver code.
Signed-off-by: NTim Bird <tim.bird@sonymobile.com>
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

On few legacy platforms, USB PHY is having dedicated reset clk.
It is used to reset USB PHY after putting USB PHY into low power
mode and for calibration of USB PHY. Putting USB PHY into low
power mode is causing ulpi read/write timeout as expected. USB PHY
reset clk is not available on newer platform.

For 28nm PHY, reset USB PHY after resetting USB LINK.
Also reset USB PHY using USB_PHY_PON bit with USB_OTG_HS_PHY_CTRL
register after programming USB PHY Override registers as suggested
with hardware programming guidelines.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NTim Bird <tim.bird@sonymobile.com>
Cc: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Allow support to use 2nd HSPHY with USB2 Core.
Some platforms may have configuration to allow USB controller
work with any of the two HSPHYs present. By default driver
configures USB core to use primary HSPHY. Add support to allow
user select 2nd HSPHY using DT parameter.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Cc: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Using reset framework eliminate need of platform specific
callbacks and enable reset lines to be specified in DT files.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Allows controller to be specified via device tree.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Function return negative code on error.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Prefix did not bring any useful information. Currently none
of the MSM platforms define these regulators, so it is safe
to rename them.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There are no references to 'pclk_src_name' in plaform code,
so it is unused.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use enum usb_dr_mode and drop default usb_dr_mode from platform data.

USB DT bindings states: dr_mode: "...In case this attribute isn't
passed via DT, USB DRD controllers should default to OTG...",
so remove redundand field.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Acked-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This fixes following:

WARNING: quoted string split across lines
WARNING: Prefer seq_puts to seq_printf
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Whether regulators are available or not is checked at driver
probe. If they are not available driver will refuse to load,
so no need to check them again.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Move memory, regulators, clocks and irq allocation to
devm_* variants. Properly check for valid clk handles.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Using platform_driver_probe() prevent driver from requesting
probe deferral. Fix this.

While at that, also switch to module_platform_driver() and
remove __init annotation from probe().
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Eliminating global variables allows driver to handle multiple
device instances.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Controller could be found on APQ and MSM platforms,
make configuration description more generic.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this makes it slightly easier to read generic CMD
logs. It also helps make sure we're sending proper
parameters for each command.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this makes it slightly easier to read link state
change interrupt logs.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

That way it's easy for humans looking at dmesg
and humans(?) looking at Databooks.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Facilitate getting required 3.3V and 1.0V VDD supply for
DWC3 controller on Exynos.

With patches for regulators' nodes merged in 3.15:
c8c253fc ARM: dts: Add regulator entries to smdk5420
275dcd22 ARM: dts: add max77686 pmic node for smdk5250,

certain perripherals will now need to ensure that,
they request VDD regulators in their drivers, and enable
them so as to make them working.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Depending on PM is not enough, because only PM_RUNTIME could be
selected. Fixes:

drivers/usb/musb/musb_dsps.c:703:12: warning: 'dsps_suspend' defined but not used [-Wunused-function]
drivers/usb/musb/musb_dsps.c:721:12: warning: 'dsps_resume' defined but not used [-Wunused-function]
Signed-off-by: NWolfram Sang <wsa@sang-engineering.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

PTR_RET is deprecated. Do not recommend its usage anymore.
Use PTR_ERR_OR_ZERO instead.
Signed-off-by: NDuan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Glue layers for the DWC3 driver only make sense on specific platforms.
Add dependencies so that they are not built where they aren't needed.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When the dsps isr sees a babble error, pass it down to the core for
fixup. Also, provide a .reset hook so the core can call us back.

A babble interrupt error occured when a USB mass storage device
("CHIPSBNK v3.3.9.1", 1e3d:2093) was disconnected from a AM33xx host.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Reported-by: NThomas Mellenthin <mellenthin@teufel.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Handle BABBLE interrupt error conditions from a work struct handler.
This indirection is necessary as we can't be certain that the phy
functions don't sleep.

Platform layer implementation may pass a babble error down to the core
in order to handle it.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Babble interrupts require us to reset the DSPS glue layer. In order to
handle all other recovery tasks independently, add a new hook for
platform-specific implementations of the actual reset.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

As gr_ep_init must be called with dev->lock held, GFP_KERNEL must not be used.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAndreas Larsson <andreas@gaisler.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Make gr_ep_enable fail properly when a call requests a larger ep.maxpacket than
ep.maxpacket_limit.
Signed-off-by: NAndreas Larsson <andreas@gaisler.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add information on ep.maxpacket_limit for each endpoint in the debugfs
information.
Signed-off-by: NAndreas Larsson <andreas@gaisler.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use an appropriate accessor function for property arrays to make the code nicer
and make the code correct if it would ever run on little endian architectures.
Suggested by Mark Rutland.
Signed-off-by: NAndreas Larsson <andreas@gaisler.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use platform_get_irq as no mapping needs to be done. No functional difference
for SPARC which is the typical environment for the driver though. Suggested by
Mark Rutland.
Signed-off-by: NAndreas Larsson <andreas@gaisler.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Provide more information on the two different interrupt cases and more
information of endpoint buffer sizes. Suggested by Mark Rutland.
Signed-off-by: NAndreas Larsson <andreas@gaisler.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Rename struct platform_device pointers from ofdev to pdev for clarity,
while at that, also use platform_set/get_drvdata() helpers.
Suggested-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NAndreas Larsson <andreas@gaisler.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>