The signal strength value is reversed: the bigger the number,
the weaker is the signal.

Fix the logic and present it in dBm. Please notice that the
dBm measure is actually an estimation, as the ratio is not
fully linear. It also varies with the frequency.

Yet, the estimation should be good enough for programs like
Kaffeine to indicate when the signal is good or bad.
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: NAbylay Ospan <aospan@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

It is a good idea to measure the signal strength while
tuning, as this helps to identify if the antenna is ok.
Also, such measure helps to identify the quality of the
signal.

Do some changes to enable it before signal lock. While
here, optimize the code to only initialize the stats
length once, and make sure that, just after set_frontend,
any reading for the stats that depends on lock to return
FE_SCALE_NOT_AVAILABLE.
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: NAbylay Ospan <aospan@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The cec_msg_request_short_audio_descriptor function was missing the reply
argument. That's needed if you want the framework to wait for the reply
message.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The cec_ops_* functions never touch cec_msg, so mark it as const.

This was done for some of the cec_ops_ functions, but not all.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add msg->len sanity checks to fix static checker warning:

	include/linux/cec-funcs.h:1154 cec_ops_set_osd_string()
	warn: setting length 'msg->len - 3' to negative one
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

- Use IS_REACHABLE(RC_CORE) instead of IS_ENABLED: if cec is built-in and
  RC_CORE is a module, then CEC can't reach the RC symbols.
- Both cec and cec-edid should be bool and use the same build 'mode' as
  MEDIA_SUPPORT (just as is done for the media controller code).
- Add a note to staging that this should be changed once the cec framework
  is moved out of staging.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The MEDIA_CEC_EDID option is guarded by MEDIA_SUPPORT, so selecting
it from MEDIA_CEC produces a warning:

warning: (MEDIA_CEC) selects MEDIA_CEC_EDID which has unmet direct dependencies (MEDIA_SUPPORT)

The warning is harmless, but it's better to add an explicit
dependency to shut it up, to reduce the noise during randconfig
builds.

Fixes: ca684386 ("[media] cec: add HDMI CEC framework (api)")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The suspend/resume functions in the s5p-cec driver are only
referenced when CONFIG_PM is enabled, so we get a warning
about unused functions otherwise:

drivers/staging/media/s5p-cec/s5p_cec.c:260:12: error: 's5p_cec_resume' defined but not used [-Werror=unused-function]
 static int s5p_cec_resume(struct device *dev)
            ^~~~~~~~~~~~~~
drivers/staging/media/s5p-cec/s5p_cec.c:253:12: error: 's5p_cec_suspend' defined but not used [-Werror=unused-function]
 static int s5p_cec_suspend(struct device *dev)

This marks them as __maybe_unused to avoid the warning without
having to introduce an extra #ifdef.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

CEC_MSG_REPORT_PHYSICAL_ADDR can theoretically be received from
an unregistered device, but in that case the code should not attempt
to write the received physical address to the phys_addrs array.

That would be pointless since there can be multiple unregistered
devices that report a physical address. We just ignore those.

While at it, improve the dprintk since it would attempt to read
from that array as well with the same out-of-bounds problem.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Like the videodev2.h and other headers, explicitly allow these headers
to be used with the BSD license.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

When a reply to an earlier transmit is received, the tx_status of that
transmit needs to be restored. Otherwise the status that the transmit
was successful would be lost.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add the keymap module for HDMI CEC remote control commands.
Signed-off-by: NKamil Debski <kamil@wypas.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

* topic/cec:
  [media] DocBook/media: add CEC documentation
  [media] s5p_cec: get rid of an unused var
  [media] move s5p-cec to staging
  [media] vivid: add CEC emulation
  [media] cec: s5p-cec: Add s5p-cec driver
  [media] cec: adv7511: add cec support
  [media] cec: adv7842: add cec support
  [media] cec: adv7604: add cec support
  [media] cec: add compat32 ioctl support
  [media] cec/TODO: add TODO file so we know why this is still in staging
  [media] cec: add HDMI CEC framework (api)
  [media] cec: add HDMI CEC framework (adapter)
  [media] cec: add HDMI CEC framework (core)
  [media] cec-funcs.h: static inlines to pack/unpack CEC messages
  [media] cec.h: add cec header
  [media] cec-edid: add module for EDID CEC helper functions
  [media] cec.txt: add CEC framework documentation
  [media] rc: Add HDMI CEC protocol handling

Linux 4.7-rc6

* tag 'v4.7-rc6': (1245 commits)
  Linux 4.7-rc6
  ovl: warn instead of error if d_type is not supported
  MIPS: Fix possible corruption of cache mode by mprotect.
  locks: use file_inode()
  usb: dwc3: st: Use explicit reset_control_get_exclusive() API
  phy: phy-stih407-usb: Use explicit reset_control_get_exclusive() API
  phy: miphy28lp: Inform the reset framework that our reset line may be shared
  namespace: update event counter when umounting a deleted dentry
  9p: use file_dentry()
  lockd: unregister notifier blocks if the service fails to come up completely
  ACPI,PCI,IRQ: correct operator precedence
  fuse: serialize dirops by default
  drm/i915: Fix missing unlock on error in i915_ppgtt_info()
  powerpc: Initialise pci_io_base as early as possible
  mfd: da9053: Fix compiler warning message for uninitialised variable
  mfd: max77620: Fix FPS switch statements
  phy: phy-stih407-usb: Inform the reset framework that our reset line may be shared
  usb: dwc3: st: Inform the reset framework that our reset line may be shared
  usb: host: ehci-st: Inform the reset framework that our reset line may be shared
  usb: host: ohci-st: Inform the reset framework that our reset line may be shared
  ...

These two fields are not used and can be removed.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

If the logical device is disabled then it can not generate interrupts.
Therefore this check is not needed.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Simplify interupt handling code.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Study states have never been used and are not needed. Remove them.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The definition of rawir includes the initialization already.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Simplify a few functions.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Wake states have never been in use and now that we can set the
wakeup sequence via sysfs there's in general no need for them.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The registers defining wakeup sequence handling are set when the
wakeup sequence is set via sysfs. There's no need to initialize them
otherwise.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

There is a rudimentary ISR for handling interrupts generated by the
wakeup part of the chip. Interrupts however have never been enabled
in the wakeup part.
Also, now that we can set the wakeup sequence via sysfs, there's in
general no need to enable interrupts in the wakeup part.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

To detect a rx fifo overrun it's checked whether the number of elements
in the chip fifo exceeds the fifo size. This check can never return true
and is wrong.
Instead we should generate an interrupt if the fifo overruns.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Disable runtime unbind as driver does not support it.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Move statistics polling to read_status() in order to avoid use of
kernel work. Also replace home made sign extension used for
statistics with kernel sign_extend32().
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Disable runtime unbind as driver does not support it.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Disable runtime unbind as driver does not support it.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Disable runtime unbind as driver does not support it.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Move statistics polling to read_status() in order to avoid use of
kernel work.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

* remove some unneeded variable initialization
* rename variables
* use min() macro to calc max i2c xfer len
* change bad firmware error code from EFAULT to EINVAL
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

There was some calculations where was kHz used in order to keep
calculation withing 32-bit. Convert all to Hz and use 64-bit
division helpers where needed.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Simplify TS clock divider calculation and programming slightly.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

DiSEqC message sending takes 13.5 ms per byte, which is 54 ms total
when typical 4 byte message is sent. Don't hard-code time limit to
54 ms, but calculate it. Time limit is only used to determine when to
start poll "DiSEqC Tx ready" status from the chip.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

No need to clear negative msb bits as those were dropped in any
case when data is written to register.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Disable runtime unbind as driver does not support it.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Disable runtime unbind as driver does not support it.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Si2168-B40 firmware API has changed somewhere between 4.0-11 and
4.0-19 so that sleep will lose firmware upgrade from the chip. Due
to that firmware re-upload is needed when newer firmwares are used.

Rewrote firmware handling logic partly at the same.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Cc: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Fix sparse warnings:

tw686x-video.c:148:29: warning: symbol 'memcpy_dma_ops' was not declared. Should it be static?
tw686x-video.c:195:29: warning: symbol 'contig_dma_ops' was not declared. Should it be static?
tw686x-video.c:361:29: warning: symbol 'sg_dma_ops' was not declared. Should it be static?
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The part can be reset by a low pulse on the RESET pin (i.e. a hardware
reset) with a minimum width of 5 ms. It is recommended to wait 5 ms
after the low pulse before an I2C write is performed to the part.
For safety reasons, the delays will be between 5 and 10 ms.

The RESET pin can be tied high, so the GPIO is optional.
Signed-off-by: NDragos Bogdan <dragos.bogdan@analog.com>
Reviewed-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>