There is no need to explicitly zero the 'ret' variable as it is properly
initialized in a few lines below as:

ret = serial_mxs_probe_dt(s, pdev);

Remove the unneeded zeroing of 'ret'.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We should check whether platform_get_irq() failed, and in the case of error
this needs to be propagated.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The irq number is only used inside the probe function, so there is no need
to keep it in the private mxs_auart_port structure.

Use a local 'irq' variable for storing the irq number instead.

Also make its type of 'int' as platform_get_irq() may fail and return a
negative number.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Digicolor USART hardware does not support detecting the BREAK condition.
This means that we can't support sysrq on this hardware. Remove all reference
to sysrq from the code.

This also fixes build when sysrq is disabled:

drivers/tty/serial/digicolor-usart.c: In function 'digicolor_uart_console_write':
drivers/tty/serial/digicolor-usart.c:407:33: error: 'struct uart_port' has no member named 'sysrq'
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the kernel command line parameter, no_console_suspend, is used,
the console should continue to output console messages during and
after system suspend. For a serial console, the serial core ensures
that the device is not shutdown when no_console_suspend is specified.
However, the default operation of the pnp bus will disable and suspend
the device and no further output occurs.

When registering the 8250 port, if the serial device is a console
set the PNP_CONSOLE capability, which prevents device power-off
if consoles are not suspending.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the serial console is an ACPI PNP device, the PNP bus always powers
down the device at system suspend, even though the no_console_suspend
command line parameter is specified (eg., when debugging suspend/resume).

Add PNP_CONSOLE capability, which when set, prevents calling both the
->disable() and ->suspend() PNP protocol methods if console suspend
is disabled.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

unregister_console() will be called from uart_remove_one_port() while
removing the platform driver. So not necessary to call it in driver
exit path.
Signed-off-by: NPramod Gurav <pramod.gurav@smartplayin.com>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The change does following:
 - baud, flow, bits, parity were being overwritten as they were
   being reinitialized after parsing.  Initialize them when they are
   declared so that user provided setting are not overwritten.
 - msm_set_baud_rate() is anyway called in uart_set_options when it calls
   msm_set_termios(). msm_reset() is called when we change the baud rate.
   Hence doing away with both of these calls.
 - CR_CMD_PROTECTION_EN and CR_TX_ENABLE settings are done in msm_set_baud_rate.
   So do away with this here.
Signed-off-by: NPramod Gurav <pramod.gurav@smartplayin.com>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Intel Moorestown platform support was removed few years ago. This is a follow
up which removes Moorestown specific code for the serial devices. It includes
mrst_max3110 and earlyprintk bits.

This was used on SFI (Medfield, Clovertrail) based platforms as well, though
new ones use normal serial interface for the console service.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When running an userspace program that does a 'tcflush(fd, TCIOFLUSH)' call
we still see the last received character in the URXD register afterwards.

Clear UCR2_SRST bit so that the UART FIFO is flushed properly.

Since UCR2_SRST also resets some UART registers, we need to save and restore
some of them.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Tested-by: NFugang Duan <B38611@freescale.com>
Acked-by: NJason Liu <r64343@freecale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On uart buffer flush, serial core resets the circular buffer.
If a DMA transfer is in progress at that time, the callback
lpuart_dma_tx_complete will move buffer's tail unconditionally,
hence tail moves beyond head. Use the flush_buffer hook to
terminate the DMA imeaditely and avoid lpuart_dma_tx_complete
being called in this situation.

This bug often showed up while shutdown and lead to duplicate
serial console output.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For power management support, we should disable TX and
TX interrupt so that kernel can prepare for deep sleep.

Retain RX and RX interrupt for wakeup the kernel when
receive the input character.
Signed-off-by: NYuan Yao <yao.yuan@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

To end a DMA transfer which did not consume a whole buffer (e.g. one
character only), a RX timer is used. When lots of data are received
the DMA transfer will complete and setup another DMA transfer, which
in turn might complete again. In this cases, it is not necessary to
abort the DMA transfers using the RX timer. This change pushes the
RX timer timeout into the future each time a DMA transfer completed.

Aborting the DMA was not very harmful, since the next received
character lead to setup of another RX DMA.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move the DMA channel request to probe to avoid requesting the DMA
channel on each opening of the ttyLPx device. This also fixes a
potential issue that TX channel is not freed when only RX channel
allocation fails. The DMA channels are now handled independently,
so one could use UART with DMA only in TX direction for instance.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the UART is in DMA receive mode (RDMAS set) and one character
just arrived while another interrupt is handled (e.g. TX), the RDRF
(receiver data register full flag) is set due to the water level of
1. But since the DMA will take care of this character, there is no
need to handle it by calling lpuart_prepare_rx. Handling it leads to
adding the RX timeout timer twice:

[   74.336698] Kernel BUG at 80053070 [verbose debug info unavailable]
[   74.342999] Internal error: Oops - BUG: 0 [#1] ARM0:00.00 khungtaskd
[   74.347817] Modules linked in:    0 S  0.0  0.0   0:00.00 writeback
[   74.350926] CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-rc3-00001-g39d78e2 #1788
[   74.358617] Hardware name: Freescale Vybrid VF610 (Device Tree)t
[   74.364563] task: 807a7678 ti: 8079c000 task.ti: 8079c000 kblockd
[   74.370002] PC is at add_timer+0x24/0x28.0  0.0   0:00.09 kworker/u2:1
[   74.373960] LR is at lpuart_int+0x15c/0x3d8
[   74.378171] pc : [<80053070>]    lr : [<802e0d88>]    psr: a0010193
[   74.378171] sp : 8079de10  ip : 8079de20  fp : 8079de1c
[   74.389694] r10: 807d44c0  r9 : 8688c300  r8 : 00000013
[   74.394943] r7 : 20010193  r6 : 00000000  r5 : 000000a0  r4 : 86997210
[   74.401498] r3 : ffffa7da  r2 : 80817868  r1 : 86997210  r0 : 86997344
[   74.408052] Flags: NzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
[   74.415489] Control: 10c5387d  Table: 8611c059  DAC: 00000015
[   74.421265] Process swapper (pid: 0, stack limit = 0x8079c230)
...

Solve this by only execute the receiver path (lpuart_prepare_rx) if
the DMA receive mode (RDMAS) is not set. Also, make sure the flag is
cleared on initialization, in case it has been left set.

This can be best reproduced using UART as a serial console, then
running top while dd'ing data into the terminal.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org> # 3.14
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the serial port gets closed while a RX transfer is in progress,
the timer might fire after the serial port shutdown finished. This
leads in a NULL pointer dereference:

[    7.508324] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[    7.516590] pgd = 86348000
[    7.519445] [00000000] *pgd=86179831, *pte=00000000, *ppte=00000000
[    7.526145] Internal error: Oops: 17 [#1] ARM
[    7.530611] Modules linked in:
[    7.533876] CPU: 0 PID: 123 Comm: systemd Not tainted 3.19.0-rc3-00004-g5b11ea7 #1778
[    7.541827] Hardware name: Freescale Vybrid VF610 (Device Tree)
[    7.547862] task: 861c3400 ti: 86ac8000 task.ti: 86ac8000
[    7.553392] PC is at lpuart_timer_func+0x24/0xf8
[    7.558127] LR is at lpuart_timer_func+0x20/0xf8
[    7.562857] pc : [<802df99c>]    lr : [<802df998>]    psr: 600b0113
[    7.562857] sp : 86ac9b90  ip : 86ac9b90  fp : 86ac9bbc
[    7.574467] r10: 80817180  r9 : 80817b98  r8 : 80817998
[    7.579803] r7 : 807acee0  r6 : 86989000  r5 : 00000100  r4 : 86997210
[    7.586444] r3 : 86ac8000  r2 : 86ac9bc0  r1 : 86997210  r0 : 00000000
[    7.593085] Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
[    7.600341] Control: 10c5387d  Table: 86348059  DAC: 00000015
[    7.606203] Process systemd (pid: 123, stack limit = 0x86ac8230)

Setup the timer on UART startup which allows to delete the timer
unconditionally on shutdown. This also saves the initialization
on each transfer.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org> # 3.14
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 26df6d13 ("tty: Add EXTPROC support for LINEMODE")
allows a process which has opened a pty master to send _any_ signal
to the process group of the pty slave. Although potentially
exploitable by a malicious program running a setuid program on
a pty slave, it's unknown if this exploit currently exists.

Limit to signals actually used.

Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Howard Chu <hyc@symas.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: <stable@vger.kernel.org> # 2.6.36+
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The vcs device's poll/fasync support relies on the vt notifier to signal
changes to the screen content.  Notifier invocations were missing for
changes that comes through the selection interface though.  Fix that.

Tested with BRLTTY 5.2.
Signed-off-by: NNicolas Pitre <nico@linaro.org>
Cc: Dave Mielke <dave@mielke.cc>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

These two copy to/from VGA memory, however on the Silicon
Motion SMI750 VGA card on a 64-bit system cause console corruption.

This is due to the hw being buggy and not handling a 64-bit transaction
correctly.

We could try and create a 32-bit version of these routines,
but I'm not sure the optimisation is worth much today.

Fixes https://bugzilla.redhat.com/show_bug.cgi?id=1132826

Tested-by: Huawei engineering.
Signed-off-by: NDave Airlie <airlied@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We want those tty fixes in that release in this branch as well.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull ARM SoC fixes from Olof Johansson:
 "We've been sitting on our fixes branch for a while, so this batch is
  unfortunately on the large side.

  A lot of these are tweaks and fixes to device trees, fixing various
  bugs around clocks, reg ranges, etc.  There's also a few defconfig
  updates (which are on the late side, no more of those).

  All in all the diffstat is bigger than ideal at this time, but nothing
  in here seems particularly risky"

* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
  reset: sunxi: fix spinlock initialization
  ARM: dts: disable CCI on exynos5420 based arndale-octa
  drivers: bus: check cci device tree node status
  ARM: rockchip: disable jtag/sdmmc autoswitching on rk3288
  ARM: nomadik: fix up leftover device tree pins
  ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
  ARM: at91/dt: sam9263: Add missing clocks to lcdc node
  ARM: at91: sama5d3: dt: correct the sound route
  ARM: at91/dt: sama5d4: fix the timer reg length
  ARM: exynos_defconfig: Enable LM90 driver
  ARM: exynos_defconfig: Enable options for display panel support
  arm: dts: Use pmu_system_controller phandle for dp phy
  ARM: shmobile: sh73a0 legacy: Set .control_parent for all irqpin instances
  ARM: dts: berlin: correct BG2Q's SM GPIO location.
  ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT
  ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host
  ARM: dts: Revert disabling of smc91x for n900
  ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling
  ARM: dts: dra7-evm: fix qspi device tree partition size
  ARM: omap2plus_defconfig: use CONFIG_CPUFREQ_DT
  ...

Pull clock driver fixes from Mike Turquette:
 "Small number of fixes for clock drivers and a single null pointer
  dereference fix in the framework core code.

  The driver fixes vary from fixing section mismatch warnings to
  preventing machines from hanging (and preventing developers from
  crying)"

* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
  clk: fix possible null pointer dereference
  Revert "clk: ppc-corenet: Fix Section mismatch warning"
  clk: rockchip: fix deadlock possibility in cpuclk
  clk: berlin: bg2q: remove non-exist "smemc" gate clock
  clk: at91: keep slow clk enabled to prevent system hang
  clk: rockchip: fix rk3288 cpuclk core dividers
  clk: rockchip: fix rk3066 pll lock bit location
  clk: rockchip: Fix clock gate for rk3188 hclk_emem_peri
  clk: rockchip: add CLK_IGNORE_UNUSED flag to fix rk3066/rk3188 USB Host

Pull SCSI fixes from James Bottomley:
 "This is one fix for a Multiqueue sleeping in invalid context problem
  and a MAINTAINER file update for Qlogic"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ->queue_rq can't sleep
  MAINTAINERS: Update maintainer list for qla4xxx

The commit 646cafc6 (clk: Change clk_ops->determine_rate to
return a clk_hw as the best parent) opens a possibility for
null pointer dereference, fix this.
Signed-off-by: NStanimir Varbanov <svarbanov@mm-sol.com>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

This reverts commit da788acb.

That commit tried to fix the section mismatch warning by moving the
ppc_corenet_clk_driver struct to init section. This is definitely wrong
because the kernel would free the memories occupied by this struct
after boot while this driver is still registered in the driver core.
The kernel would panic when accessing this driver struct.

Cc: stable@vger.kernel.org # 3.17
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

Lockdep reported a possible deadlock between the cpuclk lock and for example
the i2c driver.

       CPU0                    CPU1
       ----                    ----
  lock(clk_lock);
                               local_irq_disable();
                               lock(&(&i2c->lock)->rlock);
                               lock(clk_lock);
  <Interrupt>
    lock(&(&i2c->lock)->rlock);

 *** DEADLOCK ***

The generic clock-types of the core ccf already use spin_lock_irqsave when
touching clock registers, so do the same for the cpuclk.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: removed initialization of "flags"]

Pull dmaengine fixes from Vinod Koul:
 "Two patches, the first by Andy to fix dw dmac runtime pm and second
  one by me to fix the dmaengine headers in MAINTAINERS"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: dw: balance PM runtime calls
  MAINTAINERS: dmaengine: fix the header file for dmaengine

Pull perf fixes from Ingo Molnar:
 "Mostly tooling fixes, but also two PMU driver fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf tools powerpc: Use dwfl_report_elf() instead of offline.
  perf tools: Fix segfault for symbol annotation on TUI
  perf test: Fix dwarf unwind using libunwind.
  perf tools: Avoid build splat for syscall numbers with uclibc
  perf tools: Elide strlcpy warning with uclibc
  perf tools: Fix statfs.f_type data type mismatch build error with uclibc
  tools: Remove bitops/hweight usage of bits in tools/perf
  perf machine: Fix __machine__findnew_thread() error path
  perf tools: Fix building error in x86_64 when dwarf unwind is on
  perf probe: Propagate error code when write(2) failed
  perf/x86/intel: Fix bug for "cycles:p" and "cycles:pp" on SLM
  perf/rapl: Fix sysfs_show() initialization for RAPL PMU

Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent

Pull perf/urgent fixes from Arnaldo Carvalho de Melo:

  - Fix segfault when using both the map symtab viewer and annotation
    in the TUI (Namhyung Kim).

  - uClibc build fixes (Alexey Brodkin, Vineet Gupta).

  - bitops/hweight were moved from tools/perf/ too tools/include, move
    some leftovers (Arnaldo Carvalho de Melo)

  - Fix dwarf unwind x86_64 build error (Namhyung Kim)

  - Fix __machine__findnew_thread() error path (Namhyung Kim)

  - Propagate error code when write(2) failed in 'perf probe' (Namhyung Kim)

  - Use dwfl_report_elf() instead of offline in powerpc bits to
    properly handle non prelinked DSOs (Sukadev Bhattiprolu).

  - Fix dwarf unwind using libunwind in 'perf test' (Wang Nan)
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NIngo Molnar <mingo@kernel.org>

Merge tag 'samsung-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

Merge "Samsung fixes for v3.19" from Kukjin Kim:

Samsung fixes for v3.19
- exynos_defconfig: enable LM90 driver and display panel support
   - HWMON
   - SENSORS_LM90
   - Direct Rendering Manager (DRM)
   - DRM bridge registration and lookup framework
   - Parade ps8622/ps8625 eDP/LVDS bridge
   - NXP ptn3460 eDP/LVDS bridge
   - Exynos Fully Interactive Mobile Display controller (FIMD)
   - Panel registration and lookup framework
   - Simple panels
   - Backlight & LCD device support

- use pmu_system_controller phandle for dp phy
  : DP PHY requires pmu_system_controller to handle PMU reg. now

* tag 'samsung-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: exynos_defconfig: Enable LM90 driver
  ARM: exynos_defconfig: Enable options for display panel support
  arm: dts: Use pmu_system_controller phandle for dp phy
Signed-off-by: NOlof Johansson <olof@lixom.net>

Call spin_lock_init() before the spinlocks are used, both in early init
and probe functions preventing a lockdep splat.

I have been observing lockdep complaining [1] during boot on my a80 optimus [2]
when CONFIG_PROVE_LOCKING has been enabled. This patch resolves the splat,
and has been tested on a few other sunxi platforms without issue.

[1] http://storage.kernelci.org/next/next-20150107/arm-multi_v7_defconfig+CONFIG_PROVE_LOCKING=y/lab-tbaker/boot-sun9i-a80-optimus.html
[2] http://kernelci.org/boot/?a80-optimusSigned-off-by: NTyler Baker <tyler.baker@linaro.org>
Cc: <stable@vger.kernel.org>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'renesas-soc-fixes-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes

Merge "Renesas ARM Based SoC Fixes for v3.19" from Simon Horman:

Renesas ARM Based SoC Fixes for v3.19

This pull request is based on the last round of SoC updates for v3.19,
Fourth Round of Renesas ARM Based SoC Updates for v3.19, tagged as
renesas-soc3-for-v3.19, merged into your next/soc branch and included in
v3.19-rc1.

- ARM: shmobile: r8a7740: Instantiate GIC from C board code in legacy builds

  Set .control_parent for all irqpin instances for sh73a0 SoC when booting
  using legacy C.

- ARM: shmobile: r8a7740: Instantiate GIC from C board code in legacy builds

  This fixes a long standing problem which has been present since
  the sh73a0 SoC started using the INTC External IRQ pin driver.

  The patch that introduced the problem is 341eb546 ("ARM:
  shmobile: INTC External IRQ pin driver on sh73a0") which was included
  in v3.10.

* tag 'renesas-soc-fixes-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: sh73a0 legacy: Set .control_parent for all irqpin instances
  ARM: shmobile: r8a7740: Instantiate GIC from C board code in legacy builds

The arndale-octa board was giving "imprecise external aborts" during
boot-up with MCPM enabled. CCI enablement of the boot cluster was found
to be the cause of these aborts (possibly because the secure f/w was not
allowing it). Hence, disable CCI for the arndale-octa board.
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: NKevin Hilman <khilman@linaro.org>
Tested-by: NTyler Baker <tyler.baker@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The arm-cci driver completes the probe sequence even if the cci node is
marked as disabled. Add a check in the driver to honour the cci status
in the device tree.
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Acked-by: NSudeep Holla <sudeep.holla@arm.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Tested-by: NSudeep Holla <sudeep.holla@arm.com>
Tested-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes

Merge "at91: fixes for 3.19 #1 (ter)" from Nicolas Ferre:

First fixes batch for AT91 on 3.19:
- fix some DT entries
- correct clock entry for the at91sam9263 LCD
- add a phy_fixup for Eth1 on sama5d4

* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
  ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
  ARM: at91/dt: sam9263: Add missing clocks to lcdc node
  ARM: at91: sama5d3: dt: correct the sound route
  ARM: at91/dt: sama5d4: fix the timer reg length
Signed-off-by: NOlof Johansson <olof@lixom.net>

rk3288 SoCs have a function to automatically switch between jtag/sdmmc pinmux
settings depending on the card state. This collides with a lot of assumptions.

It only works when using the internal card-detect mechanism and breaks
horribly when using either the normal card-detect via the slot-gpio function
or via any other pin. Also there is of course no link between the mmc and jtag
on the software-side, so the jtag clocks may very well be disabled when the
card is ejected and the soc switches back to the jtag pinmux.

Leaving the switching function enabled did result in mmc timeouts and rcu
stalls thus hanging the system on 3.19-rc1. Therefore disable it in all cases,
as we expect the devicetree to explicitly select either mmc or jtag pinmuxes
anyway.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'berlin-fixes-for-3.19-1' of git://git.infradead.org/users/hesselba/linux-berlin into fixes

Merge "ARM: berlin: Fixes for v3.19 (round 1)" from Sebastian Hesselbarth:

Marvell Berlin fixes for v3.19 round 1:
- SDHCI DT fixes for BG2Q and BG2Q reference board
- BG2Q SM GPIO DT node relocation

* tag 'berlin-fixes-for-3.19-1' of git://git.infradead.org/users/hesselba/linux-berlin:
  ARM: dts: berlin: correct BG2Q's SM GPIO location.
  ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT
  ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host
Signed-off-by: NOlof Johansson <olof@lixom.net>

We altered the device tree bindings for the Nomadik family of
pin controllers to be standard, this file was merged out-of-order
so we missed fixing this. Fix it up.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>