Fix a bug where ethtool set-channels would return failure when configuring
only one Rx queue.

Change-ID: Id833c48c17d71e352b30f3249f6acf9e7aaec57e
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

These changes make Doxygen/kdoc work correctly without warnings.

Change-ID: I2941f38860be805ff7548d84dae35754c83f1d62
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>

Avoid over-length lines in order to appease checkpatch.

Change-ID: I63820a710acf798f49d2f85c610228711af84f72
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update driver version to 0.3.27-k
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current driver will warn the user if the NVM version
is out of date, this raises the bar to a newer version.

Change-ID: I5ec21d8efa4e7c3fdacb56f85d310bb2229b1483
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A previous commit removed any need for these macros, so remove
them too.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

These instances were found by coccinelle/spatch, and can
use struct assignment instead of memcpy.

Change-ID: Idc23c3599241bf8a658bda18c80417af3fbfee66
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver needs to set the MFP flag earlier in i40e_sw_init
and then can use that flag to decide if other hardware
work-arouds are required.

Change-ID: Ib17ad1e3485f57b28845ab4722294a99f203bd48
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The hardware requires a full packet template to be pointed to when adding
hardware flow filters.  This patch adds the template and uses it for
programming filters.

Change-ID: I09db9f4ab0207ca9c520ae36596d74e1a0663ae5
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch does s/rebuid/rebuild/.

Change-ID: I77ff0c26db3d23ca5dc971b82d71b4ed8c6bcc14
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix some badly formatted lines, long lines and a mis-formatted else.

Change-ID: Iac2eef064ae27c55a0c3d9c15c525bf8fed8ab6f
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The alloc_rx_buff_failed and alloc_rx_page_failed variables
are both part of an rx specific structure so just remove
the _rx part of the name.  No functional changes.

Change-ID: Icffa2f5d13c6f2b1e09cf45b9472b83c9dae8fc6
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The admin queue can be used to send messages among the physical
function interfaces.  This adds the code to handle that case.

Change-ID: I0700fcc47e41433131a381f0eb72fc7b01b6bd87
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since nearly everything we do is synchronous, using the interrupt-on-error bit
is unnecessary and causing unneeded interrupts.  If anyone wants to use the bit
they can turn it on in individual AQ requests using the cmd_details parameter.

Change-ID: I4690a9c561d3e0836aeadb4f88f8a8702b1d1366
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Call AQ to release any reservation held by this PF on the NVM resource
lock on startup, in order to clear anything that might have been left over from
a previous run.  The lock is only cleared by the requestor calling for it to be
cleared, on power-on, or firmware reset.  This should help limit the need for
rebooting a customer machine if something goes wrong on a firmware update or
some other action.

Change-ID: I8c8473e601d4ef512dda7baa77a6e75f2e5fea49
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

RSS initialization was doing some extra work, remove the extra
work and any bugs it created when managing number of queues.

Change-ID: Iea75b04a70d73ce76947b6a177ce89ab4899d4c6
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver and hardware support splitting packets on headers
but with the use of GRO we don't need the extra bus
overhead, so make this driver more like igb and ixgbe and
disable packet split.

Change-ID: Id42f2c3736baa9d5bdfe1f72d64226e7d8ebd737
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The memory barrier used in maybe_stop_tx can use a comment.

Also add checks to VSI->rx_rings to ensure a kernel panic is not induced.

Change-ID: I48cc1bf1d6cf301818155b737edeef77c0d790c7
Change-ID: I1363a8445fbf521a26267849966296ed55f43ad8
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The MAC address format expected by the hardware is in a very specific
format, and the driver was filling in the data incorrectly.

Change-ID: I7bc66505ef459ee347dd3bda68051004c141c689
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The GPL header included in each file in the i40e driver doesn't
need to include the "this program" text since this driver
is already part of the larger kernel.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Replace uses of I40E_LENGTH_OF_ADDRESS with ETH_ALEN.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The hardware can occasionally give an interrupt on the misc
queue for which there is no driver work to do.  In that case
the driver was not re-enabling interrupts even though they
were auto masked by hardware.  This left interrupts disabled
on this queue.

Re-enable the interrupt whenever leaving this function.
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When cleaning descriptors, we must set up ALL fields, not just the DMA
address. The initial setup does this correctly, but not the cleanup
code, so the firmware would process the ring exactly once and then fail.

Change-ID: I2930b83c76194b3016a8ac0fa693f9a573995640
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The admin queue length register is updated in
config_a<sq|rq>_regs functions.  We should not update it again,
as we will trigger firmware to init the AQ again. In this case
firmware will lose the information about the AQ Rx tail position
and will see Rx queue as full (no free desc for FW to use).
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The PF VSI was never updated to enable or disable internal switch loopback
when VFs were created or destroyed via the sysfs interface.  Add some
helper functions to take care of that.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Addresses a few code format issues that have crept in over time.

Change-Id: I1a62cbd16b29a218a933b0f7176abe748f9615e8
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Rework Shadow RAM read word/buffer functions to not use AQ Request
Resource commands.  Requesting resource is not needed for SR read
operations which are done through SRCTL register.  Access to SR through
register is controlled through DONE bit within SRCTL.  With this change
we do not block whole NVM resource for SR read operations.

Change-Id: I73e96cdea39a45ee7b5bdf038e527308de2d9efe
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We need to check if we are dealing with the correct MAC type before we
try to read anything from the registers.

Change-Id: I3989516999d06c3009e87d6a2eafc20af305c5c2
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move PF ID initialization code from PF reset routine to earlier driver
initialization function.  There are a few operations which need the
PF ID before the first PF reset is called.

Change-Id: I7e971f7556b46a837149850ec05ce115c35db575
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use a smaller range of test registers in MFP mode as there are fewer
resources than when in SFP mode.

Change-Id: I08424890c3f57b5dde5ee99e99724ce252e0875a
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The firmware's AdminQ interface has matured a little, so update the
code to use the new fields and values.

Change-Id: I8fcd7b443f268dcf9346bd6a9e940fe9c2958891
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The RSTAT comes back with DEVICE READY to indicate that the HW is ready,
but we still have to wait for the FW to indicate that the Core and Global
modules are back up again.  This needs a read of the NVM_ULD register.

Change-Id: I88276165f9cd446d2f166fb4b8cff00521af4bec
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Version update to 0.3.25-k
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The VF is allowed to request the PF to set its already assigned
MAC address without generating an error.

Change-Id: I8dfdf353396995dbbb26cafab4e42b451911da3d
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the 8021q driver is loaded it sets VLAN 0 filters on all devices.
This does not mean that any VLAN tagged packet should be accepted.
Instead accept only VLAN 0 tagged packets so that upper layers can
interpret the priority bits.

Change-Id: I17274a540b613749612ffe23a3aef2b8ee6ff6a4
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Broadcast promiscuous should only be turned on when general
promiscuous mode is turned on, otherwise VLAN tagged packets out of
the assigned VLAN domain are received.

Add a broadcast MAC filter in order to continue to receive
broadcast traffic on VLANs, MAIN or VMDQ VSI.

Change-Id: I99d8e382a082ee51201228f1226af3b46452ac55
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add more functionality to debugfs to assist development
and testing of AQ commands.

adds:
send aq_cmd
send indirect aq_cmd

Change-Id: I01710cddd33110a6c1e1aabf84cb6e93cda4c42a
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the device is not in a working state avoid making admin
queue (AQ) calls that rely on a working AQ.

Change-Id: Ifbba6d257b3a5b51bfe92938c04088c0baa21433
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Driver needs to make sure the send queue is alive before
trying to use it.

Chagne-Id: I9bd1f6159c45c98e63f562e3a8dfb57edfe50e13
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Always call the AQ call to shutdown the queue in the shutdown path.

Check ASQ is alive before issuing the AQ command since we might be
resetting to recover from a bad state in which case we should not
issue the AQ command.

Use the register variable for length so it can be used by PF, VF
and GL AQ commands.

Change-Id: Ic3d305687ea3f1a6afa84e864b7a27bd38a9af32
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>