To configure the virtual PMUv3 overflow interrupt number, we use the
vcpu kvm_device ioctl, encapsulating the KVM_ARM_VCPU_PMU_V3_IRQ
attribute within the KVM_ARM_VCPU_PMU_V3_CTRL group.

After configuring the PMUv3, call the vcpu ioctl with attribute
KVM_ARM_VCPU_PMU_V3_INIT to initialize the PMUv3.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Acked-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

To support guest PMUv3, use one bit of the VCPU INIT feature array.
Initialize the PMU when initialzing the vcpu with that bit and PMU
overflow interrupt set.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Acked-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

When KVM frees VCPU, it needs to free the perf_event of PMU.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

When resetting vcpu, it needs to reset the PMU state to initial status.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

When calling perf_event_create_kernel_counter to create perf_event,
assign a overflow handler. Then when the perf event overflows, set the
corresponding bit of guest PMOVSSET register. If this counter is enabled
and its interrupt is enabled as well, kick the vcpu to sync the
interrupt.

On VM entry, if there is counter overflowed and interrupt level is
changed, inject the interrupt with corresponding level. On VM exit, sync
the interrupt level as well if it has been changed.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

According to ARMv8 spec, when writing 1 to PMCR.E, all counters are
enabled by PMCNTENSET, while writing 0 to PMCR.E, all counters are
disabled. When writing 1 to PMCR.P, reset all event counters, not
including PMCCNTR, to zero. When writing 1 to PMCR.C, reset PMCCNTR to
zero.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Add access handler which emulates writing and reading PMSWINC
register and add support for creating software increment event.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Since the reset value of PMOVSSET and PMOVSCLR is UNKNOWN, use
reset_unknown for its reset handler. Add a handler to emulate writing
PMOVSSET or PMOVSCLR register.

When writing non-zero value to PMOVSSET, the counter and its interrupt
is enabled, kick this vcpu to sync PMU interrupt.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

When we use tools like perf on host, perf passes the event type and the
id of this event type category to kernel, then kernel will map them to
hardware event number and write this number to PMU PMEVTYPER<n>_EL0
register. When getting the event number in KVM, directly use raw event
type to create a perf_event for it.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Since the reset value of PMCNTENSET and PMCNTENCLR is UNKNOWN, use
reset_unknown for its reset handler. Add a handler to emulate writing
PMCNTENSET or PMCNTENCLR register.

When writing to PMCNTENSET, call perf_event_enable to enable the perf
event. When writing to PMCNTENCLR, call perf_event_disable to disable
the perf event.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

These kind of registers include PMEVCNTRn, PMCCNTR and PMXEVCNTR which
is mapped to PMEVCNTRn.

The access handler translates all aarch32 register offsets to aarch64
ones and uses vcpu_sys_reg() to access their values to avoid taking care
of big endian.

When reading these registers, return the sum of register value and the
value perf event counts.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>