Testmode (TCMD and ART) was not enabled when fw-2.bin or fw-3.bin files
were available, fix that by fetching testmode file just after the
board file but before rest of the firmware files are fetched.

I also added testmode field to struct ath6kl and moved the module parameter
to core.c. Now all module parameters are grouped in one place.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently rx aggregation related states are maintained per
vif, but this will not properly work when operating in AP mode.
Aggregation is completely broken when more than one
11n stations are connected to AP mode vif. Fix this issue
by keeping station specific aggregation state in sta_list.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The tid which is given in addba/delba req event is not
just tid but also muxed with the assoc id (MSB 4 bits)
which can be used to determine the corresponding connected
station in softap mode. The actual tid is LSB 4 bits. Using
the tid as it is with rx_tid[] would result in OOB or invalid
memory access in AP mode.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This will be used when initializing station specific aggregation
information.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch just groups connection specific aggregation information
from struct aggr_info into a new structure (struct aggr_info_conn)
so that, in softAP mode, this can be used when each connected station
is made to have it's own aggregation state.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The patch "ath6kl: create core.c" removes wiphy_free() from
ath6kl_cfg80211_cleanup() and misses to free wiphy in
ath6kl_sdio_remove(). This patch fixes this regression.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The timer which is used to flush rx aggregation frames needs to
be disabled when resetting the aggregation state. This is found
in code review.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

John Linville had to revert the part of USB support which was already
in ath6kl due to build problems in commit cb00ec38 ("ath6kl: revert
USB support"). Now that I fixed the build problems properly by adding
ath6kl_core.ko kernel module it's possible to add back the
(incomplete) USB support. This patch is a revert of John's patch and
adds back the USB code which as already in ath6kl, only difference
being minor changes in Makefile and adapting usb.c to new core
function names.

Note that USB support in ath6kl is not complete yet. This code only
makes it possible to boot firmware but as HTC layer does not yet
support USB it's not possible to send any WMI commands nor data
packets to the firmware. That will be added soon.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Now ath6kl is ready for splitting core code to ath6kl_core.ko module.
This also makes it possible to link both sdio and usb code to kernel
at the same time, which earlier failed miserably.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

That way it's possible to not export debug_mask outside the upcoming
ath6kl_core.ko and that makes it easier to ath6kl_core.ko in the
following patch.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

We don't need it as debug calls already have a log level and compiler
should be smart enough to optimise away the code when ath6kl debug code
is not enabled. Also it makes it easier to abstract core code to
ath6kl_core.ko.

In ath6kl_dump_registers() I had to change the debug level from ANY to IRQ
as I removed the AR_DBG_LVL_CHECK() check before calling the function.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently core functions are spread between various files, group all
the functions into file and rename the functions to follow the style
used elsewhere in the driver. This will make it easier to a separate core
module.

Also fix a bug where wiphy is freed too early.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add ATH6KL_CONF_UART_DEBUG which is set whenever uart_debug module
parameter is enabled. This way we can keep the uart_debug parameter
static when core.c file is introduced.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Group them together and change the naming to follow the common style in
ath6kl. No functional changes.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath6kl_cfg80211_vif_init/cleanup() follow more closely the style used
elsewhere in ath6kl.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add testmode 2 for 6003 ART. When you insmod ath6kl_sdio.ko testmode=2, ath6kl
will load ART firmware utf.bin and testscript nullTestFlow.bin. These files
should be put in the firmware folder.

kvalo: add "ath6kl:" to the title, word wrap the commit log and remove
extra line in the code
Signed-off-by: NAlex Yang <xiaojuny@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Before I commited patch c1762a3f ("ath6kl: Add support for uAPSD") I
did a minor change how up variable is initialised in
ath6kl_process_uapsdq(). But I was sloppy and caused this compiler
warning:

txrx.c:88:5: warning: 'up' may be used uninitialized in this function

Revert my change to fix the warning.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

As drivers/net/wireless/ath/Makefile contains the flag to enable
endian checks there's no need to have it in ath6kl makefile anymore.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Commit c8f44aff ("net: introduce and use netdev_features_t for
device features sets") added netdev_features_t to ndo_set_features.
Change ath6kl to use the new type.

This fixes a warning:

ath6kl/main.c:1170: warning: initialization from incompatible pointer type
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath6kl_read_fwlogs() assigns the value zero to the variable 'ret'
at the time of declaration. Later, return value of ath6kl_diag_read32()
repalces the init value. Hence removing useless zero assignment.
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

* A new APSD power save queue is added in the station structure.
* When a station has APSD capability and goes to power save, the frame
  designated to the station will be buffered in APSD queue.
* When the host receives a frame which the firmware marked as trigger,
  host delivers the buffered frame from the APSD power save queue.
  Number of frames to deliver is decided by MAX SP length.
* When a station moves from sleep to awake state, all frames buffered
  in APSD power save queue are sent to the firmware.
* When a station is disconnected, all frames bufferes in APSD power save
  queue are dropped.
* When the host queues the first frame to the APSD queue or removes the
  last frame from the APSD queue, it is indicated to the firmware using
  WMI_AP_APSD_BUFFERED_TRAFFIC_CMD.

kvalo: fix buggy handling of sks queues, made it more obvious
the user priority when wmm is disabled, remove unneed else block and
combined some variable declarations
Signed-off-by: NThirumalai Pachamuthu <tpachamu@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch addresses a few problems with the commit:

"ath6kl: Implement support for listen interval from userspace"

* The debugfs file required for reading/writing the listen interval
  wasn't created. Fix this.

* The interface index was being hardcoded to zero. Fix this.

* Two separate parameters, "listen_interval_time and listen_interval_beacons"
  were being used. This fails to work as expected because the FW assigns
  higher precedence to "listen_interval_beacons" and "listen_interval_time"
  ends up being never used at all.

  To handle this, fix the host driver to exclusively use listen interval
  based on units of beacon intervals.

To set the listen interval, a user would now do something like this:

echo "10" > /sys/kernel/debug/ieee80211/*/ath6kl/listen_interval

kvalo: fix two checkpatch warnings
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This prevents 'comp_pktq' from being used in an
incorrect manner.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

'params' is already used earlier and there is no point
in checking for a NULL condition again.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

sdio_release_host() would be called twice if sdio_set_block_size()
fails for some reason, which would result in the following warning.

WARNING: at /home/sujith/dev/wireless-testing/drivers/mmc/core/core.c:828 mmc_release_host+0x42/0x50 [mmc_core]()

Call Trace:
[<ffffffff81064fdf>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8106503a>] warn_slowpath_null+0x1a/0x20
[<ffffffffa03beb42>] mmc_release_host+0x42/0x50 [mmc_core]
[<ffffffffa03c917e>] sdio_release_host+0x1e/0x30 [mmc_core]
[<ffffffffa053fac7>] ath6kl_sdio_config+0xc7/0x110 [ath6kl_sdio]
[<ffffffffa053fd2c>] ath6kl_sdio_probe+0x21c/0x320 [ath6kl_sdio]
[<ffffffffa03beb2a>] ? mmc_release_host+0x2a/0x50 [mmc_core]
[<ffffffffa03c7d2a>] sdio_bus_probe+0xfa/0x130 [mmc_core]
[<ffffffff813015ae>] driver_probe_device+0x7e/0x1b0
[<ffffffff8130178b>] __driver_attach+0xab/0xb0
[<ffffffff813016e0>] ? driver_probe_device+0x1b0/0x1b0
[<ffffffff813016e0>] ? driver_probe_device+0x1b0/0x1b0
[<ffffffff81300504>] bus_for_each_dev+0x64/0xa0
[<ffffffff8130123e>] driver_attach+0x1e/0x20
[<ffffffff81300e80>] bus_add_driver+0x1b0/0x280
[<ffffffffa0065000>] ? 0xffffffffa0064fff
[<ffffffff81301d06>] driver_register+0x76/0x140
[<ffffffffa0065000>] ? 0xffffffffa0064fff
[<ffffffffa03c7b71>] sdio_register_driver+0x21/0x30 [mmc_core]
[<ffffffffa0065012>] ath6kl_sdio_init+0x12/0x35 [ath6kl_sdio]
[<ffffffff81002042>] do_one_initcall+0x42/0x180
[<ffffffff810b025f>] sys_init_module+0x8f/0x200
[<ffffffff81425ac2>] system_call_fastpath+0x16/0x1b
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

More drivers where net_device_ops should be const.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool_ops table of function pointers should be const.
Fix all the usb network drivers.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently this race is handled but in a messy way an atomic
variable is being checked in a loop which sleeps upto ms
in every iteration. Remove this logic and use a mutex
to make sure irq is not disabled when irq handling is in
progress.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Otherwise if (ielen <= ATH6KL_MAX_IE) is dead code. It looks safe to
change the type of ielen from u8 to size_t instead of removing this
if check, this ielen can have the length of more than one ies in future.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In ath6kl_reset_device(), since control can never reach switch..case
when the target_type is neither TARGET_TYPE_AR6003 nor TARGET_TYPE_AR6004,
remove the default option of switch statement.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There are maximum of seven multicast filter are supported
by hw. When the requested number of filters exceeds the
maximum supported one, multicast filtering is completely
disabled, the requested filters will be configured in
firmware and the only multicast frames that host is interested
in will be passed to host for further processing otherwise.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>

This will be used to disable/enable multicast receive.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>

The driver uses __napi_complete and napi_gro_receive. Without it, the
driver hits the BUG_ON(n->gro_list) assertion hard in __napi_complete.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Tested-by: NMarin Glibic <zhilla2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The energy detect enable/disable code in the driver uses some
register defines in this header unconditionally, so guarding
the smscphy.h header include with CONFIG_SMSC_PHY leads to
build failures in some configurations.
Reported-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At this point if skb->len happens to be 2, the subsequant skb_pull(skb, 4)
call won't work and the skb->len won't be decreased and won't ever reach 0,
resulting in an infinite loop.

With an ASIX 88772 under heavy load, without this patch, rx_fixup() reaches
an infinite loop in less than a minute. With this patch applied,
no infinite loop even after hours of heavy load.
Signed-off-by: NAurelien Jacobs <aurel@gnuage.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 4e16d6eb (r6040: define more MCR0
register bits) added #define values for MCR0 register bits and converted
uses of hardcoded magic values to uses of these defines.

However, one of the conversions looks suspicious:

 #define MCR0		0x00	/* Control register 0 */
+#define  MCR0_RCVEN	0x0002	/* Receive enable */
+#define  MCR0_XMTEN	0x1000	/* Transmission enable */

 	/* Init RDC private data */
-	lp->mcr0 = 0x1002;
+	lp->mcr0 = MCR0_XMTEN | MCR0;

I believe what was meant here was MCR0_XMTEN | MCR0_RCVEN, which makes
sense and matches the original values.
Signed-off-by: NCesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a bnx2x device encounters parity errors, it will not respond to all
SPQ messages.  As a result, the shutdown sequence before reset can take
a long time as the ulp drivers (bnx2i/bnx2fc) have to wait for timeout
of all such messages.

To improve this scenario, when bnx2x returns error on the SPQ, we'll send
an immediate response to the ulp drivers to avoid such lengthy timeouts.

Adjust the return code of relevant functions to return error only if
the message cannot be sent on the SPQ so that we'll generate an error
completion to the ulp drivers.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>