This patch adds support for the SPI controller found on the Broadcom BCM63xx
SoCs.
Signed-off-by: NTanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

CSR SiRFprimaII has two SPIs (SPI0 and SPI1). Features:
* Master and slave modes
* 8-/12-/16-/32-bit data unit
* 256 bytes receive data FIFO and 256 bytes transmit data FIFO
* Multi-unit frame
* Configurable SPI_EN (chip select pin) active state
* Configurable SPI_CLK polarity
* Configurable SPI_CLK phase
* Configurable MSB/LSB first
Signed-off-by: NZhiwu Song <zhiwu.song@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch adds SuperH HSPI driver.
It is still prototype driver, but has enough function at this point.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The SH7757 has RSPI module. This patch supports it.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

It was equivalent to spi-gpio, and there's no longer any in-tree users
of it, so get rid of it.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Sort the SPI makefile and enforce the naming convention spi_*.c for
spi drivers.

This change also rolls the contents of atmel_spi.h into the .c file
since there is only one user of that particular include file.

v2: - Use 'spi-' prefix instead of 'spi_' to match what seems to be
      be the predominant pattern for subsystem prefixes.
    - Clean up filenames in Kconfig and header comment blocks
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

The Blackfin SPORT peripheral is a pretty flexible device.  With enough
coaching, we can make it generate SPI compatible waveforms.  This is
desirable as the SPORT can run at much higher clock frequencies than the
dedicated on-chip SPI peripheral, and it can do full duplex DMA.  It also
opens up the possibility of multiple SPI buses in case someone wants to
dedicate a whole bus to a specific part that does not play well with
others.
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch adds an SPI master implementation that operates on top of an
underlying TI-SSP port.
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

The SH7757 has SPI0 module. This patch supports it.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[grant.likely@secretlab.ca: fixed Makefile ordering, added
    __dev{init,exit} annotations, removed DRIVER_VERSION (this is
    mainline, the version == the kernel version) and tidied some
    indentation & style stuff]
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch adds a new SPI driver to support the Altera SOPC Builder
SPI component. It uses the bitbanging library.
Signed-off-by: NThomas Chou <thomas@wytron.com.tw>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch adds support of OpenCores tiny SPI driver.

http://opencores.org/project,tiny_spiSigned-off-by: NThomas Chou <thomas@wytron.com.tw>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The Atheros AR71XX/AR724X/AR913X SoCs have a built-in SPI controller. This
patch implements a driver for that.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: spi-devel-general@lists.sourceforge.net
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1960/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

dw_spi driver in upstream only supports PIO mode, and this patch
will support it to cowork with the Designware dma controller used
on Intel Moorestown platform, at the same time it provides a general
framework to support dw_spi core to cowork with dma controllers on
other platforms

It has been tested with a Option GTM501L 3G modem and Infenion 60x60
modem. To use DMA mode, DMA controller 2 of Moorestown has to be enabled

Also change the dma interface suggested by Linus Walleij.
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NFeng Tang <feng.tang@intel.com>
[Typo fix and renames to match intel_mid_dma renaming]
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Sodaville's SPI controller is very much the same as in PXA25x. The
difference:
- The RX/TX FIFO is only 4 words deep instead of 16
- No DMA support
- The SPI controller offers a CS functionality
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NDirk Brandewie <dirk.brandewie@gmail.com>

Now that the of_platform_bus_type has been merged with the platform
bus type, a single platform driver can handle both OF and non-OF use
cases.  This patch merges the OF support into the platform driver.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Tested-by: NMichal Simek <monstr@monstr.eu>

This patch merges the platform driver support into the main body of
xilinx_spi.c in preparation for merging the OF and non-OF support
code.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Tested-by: NMichal Simek <monstr@monstr.eu>

v2 changes:
  from Thierry Reding:
    * add "select TEGRA_SYSTEM_DMA" to Kconfig
  from Grant Likely:
    * add oneline description to header
    * inline references to DRIVER_NAME
    * inline references to BUSY_TIMEOUT
    * open coded bytes_per_word()
    * spi_readl/writel -> spi_tegra_readl/writel
    * move transfer validation to spi_tegra_transfer
    * don't request_mem_region iomem as platform bus does that for us
    * __exit -> __devexit

v3 changes:
  from Russell King:
    * put request_mem_region back int
  from Grant Likely:
    * remove #undef DEBUG
    * add SLINK_ to register bit defines
    * remove unused bytes_per_word
    * make spi_tegra_readl/writel static linine
    * various refactoring for clarity
    * mark err if BSY bit is not cleared after 1000 retries
    * move spinlock to protect setting of RDY bit
    * subsys_initcall -> module_init

v3 changes:
  from Grant Likely:
    * update spi_tegra to use PTR_ERRless dma API

v4 changes:
  from Grant Likely:
    * remove empty spi_tegra_cleanup fucntion
    * allow device ids of -1
Signed-off-by: NErik Gilling <konkers@android.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Russell King <linux@arm.linux.org.uk>

spi: tegra: cleanups from upstream review

Change-Id: Icecf7e64efcb39de072a15234ba1faa4bad40d25
Signed-off-by: NErik Gilling <konkers@android.com>

Add eSPI controller support based on the library code spi_fsl_lib.c.

The eSPI controller is newer controller 85xx/Pxxx devices supported.
There're some differences comparing to the SPI controller:

1. Has different register map and different bit definition
   So leave the code operated the register to the driver code, not
   the common code.

2. Support 4 dedicated chip selects
   The software can't controll the chip selects directly, The SPCOM[CS]
   field is used to select which chip selects is used, and the
   SPCOM[TRANLEN] field is set to tell the controller how long the CS
   signal need to be asserted. So the driver doesn't need the chipselect
   related function when transfering data, just set corresponding register
   fields to controll the chipseclect.

3. Different Transmit/Receive FIFO access register behavior
   For SPI controller, the Tx/Rx FIFO access register can hold only
   one character regardless of the character length, but for eSPI
   controller, the register can hold 4 or 2 characters according to
   the character lengths. Access the Tx/Rx FIFO access register of the
   eSPI controller will shift out/in 4/2 characters one time. For SPI
   subsystem, the command and data are put into different transfers, so
   we need to combine all the transfers to one transfer in order to pass
   the transfer to eSPI controller.

4. The max transaction length limitation
   The max transaction length one time is limitted by the SPCOM[TRANSLEN]
   field which is 0xFFFF. When used mkfs.ext2 command to create ext2
   filesystem on the flash, the read length will exceed the max value of
   the SPCOM[TRANSLEN] field.
Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Refactor the common code in file spi_fsl_spi.c to spi_fsl_lib.c used
by SPI/eSPI controller driver as a library, and leave the QE/CPM SPI
controller code in the SPI controller driver spi_fsl_spi.c.

Because the register map of the SPI controller and eSPI controller
is so different, also leave the code operated the register to the
driver code, not the common code.
Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This will pave the way to refactor out the common code which can be used
by the eSPI controller driver, and rename the SPI controller dirver to the
file spi_fsl_spi.c.
Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Replace EXTRA_CFLAGS with ccflags-y.
Signed-off-by: Nmatt mooney <mfm@muteddisk.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Topcliff PCH is the platform controller hub that is going to be used
in Intel's upcoming general embedded platform. All IO peripherals in
Topcliff PCH are actually devices sitting on AMBA bus.  This patch
adds a driver for the SPI bus integrated into the Topcliff device.
Signed-off-by: NMasayuki Ohtake <masa-korg@dsn.okisemi.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NJohn Rigby <jcrigby@gmail.com>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch adds an SPI master driver for the Cirrus EP93xx SPI controller found
in EP93xx chips.
Signed-off-by: NMika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Adds a memory-mapped I/O dw_spi platform device.
Signed-off-by: NJean-Hugues Deschenes <jean-hugues.deschenes@octasic.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add support for the QSPI controller found some on Freescale/Motorola
Coldfire MCUs.

Full duplex, active high cs, spi modes 0-3 and word sizes 8-16 bits are
supported.  The hardware drives the MISO, MOSI and SCLK lines, but the chip
selects are managed via GPIO and must be configured by the board code.

The QSPI controller has an 80 byte buffer which allows us to transfer up to 16
words at a time.  For transfers longer than 16 words, we split the buffer in
half so we can update in one half while the controller is operating on the
other half.  Interrupt latencies then ultimately limits our sustained thru-put
to something less than half the maximum speed supported by the part.
Signed-off-by: NSteven King <sfking@fdwdc.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch adds support for a SPI master driver for the
DaVinci series of SOCs
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPhilby John <pjohn@in.mvista.com>
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Each SPI controller has exactly one CS line and as such doesn't
provide for multi-cs. We implement a workaround to support
multi-cs by _not_ configuring the mux'ed CS pin for each SPI
controller. The CS mechanism is assumed to be fully machine
specific - the driver doesn't even assume some GPIO pin is used
to control the CS.

The driver selects between DMA and POLLING mode depending upon
the xfer size - DMA mode for xfers bigger than FIFO size, POLLING
mode otherwise.

The driver has been designed to be capable of running SoCs since
s3c64xx and till date, for that reason some of the register fields
have been passed via, SoC specific, platform data.
Signed-off-by: NJassi Brar <jassi.brar@samsung.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add pseudo-DMA by FIQ to the S3C24XX SPI driver.  This allows the driver
to get DMA-like performance where there are either no free DMA channels or
when doing transfers that required both TX and RX data paths.

Since this patch requires the addition of an assembly file to hold the FIQ
code, we rename the module (instead of adding a rename of the .c file to
this patch).  We expect most users are loading this via udev and thus
there should be no change to the userland configuration.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NSimtec Linux Team <linux@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Driver for the Designware SPI core, it supports multipul interfaces like
PCI/APB etc.  User can use "dw_apb_ssi_db.pdf" from Synopsys as HW
datasheet.

[randy.dunlap@oracle.com: fix build]
[akpm@linux-foundation.org: build fix]
Signed-off-by: NFeng Tang <feng.tang@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This change adds the OMAP SPI 100k driver created by
Fabrice Crohas <fcrohas@gmail.com>.  This SPI bus is found on
OMAP7xx-series smartphones, and for many, the touchscreen is
attached to this bus.

The lion's share of the work was done by Fabrice on this driver --
I am merely porting it from the Linwizard project on his behalf.
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NWan ZongShun <mcuos.com@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch is V2 of SPI Master support for the SuperH MSIOF.
Full duplex, spi mode 0-3, active high cs, 3-wire and lsb
first should all be supported, but the driver has so far
only been tested with "mmc_spi".

The MSIOF hardware comes with 32-bit FIFOs for receive and
transmit, and this driver simply breaks the SPI messages
into FIFO-sized chunks. The MSIOF hardware manages the pins
for clock, receive and transmit (sck/miso/mosi), but the chip
select pin is managed by software and must be configured as
a regular GPIO pin by the board code.

Performance wise there is still room for improvement, but
on a Ecovec board with the built-in sh7724 MSIOF0 this driver
gets Mini-sd read speeds of about half a megabyte per second.

Future work include better clock setup and merging of 8-bit
transfers into 32-bit words to reduce interrupt load and
improve throughput.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch adds in a platform device driver using the xilinx_spi common module.
Tested-by: NJohn Linn <John.Linn@xilinx.com>
Signed-off-by: NRichard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch splits the xilinx_spi driver into a generic part and a
OF driver part.

The reason for this is to later add in a platform driver as well.
Tested-by: NJohn Linn <John.Linn@xilinx.com>
Signed-off-by: NRichard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Adds support for the dedicated SPI device on the Freescale MPC5200(b)
SoC.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This makes the filename match the Kconfig symbol and the driver name.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add SPI driver for Freescale STMP 3xxx-based boards

[dbrownell@users.sourceforge.net: cleanup sequence, spi_unregister_master]
Signed-off-by: Ndmitry pervushin <dpervushin@embeddedalley.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Timur Tabi <timur@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This driver has been tested on i.MX1/i.MX27/i.MX35 with an AT25 type
EEPROM and on i.MX27/i.MX31 with a Freescale MC13783 PMIC.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Tested-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Cc: Andrea Paterniani <a.paterniani@swapp-eng.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds a SPI driver for the SPI controller found in the IBM/AMCC
4xx PowerPC's.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NWolfgang Ocker <weo@reccoware.de>
Acked-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: NSteven A. Falco <sfalco@harris.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>