Currently power management is supported only when only a single
virtual interface is present. The driver verifies number of created
interfaces and disables power management when multiple interfaces
present. However, this rule does not extend to a P2P device that is
handled differently in the firmware. If a P2P device is added power
management can remain enabled.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Replace SLEEP_OVER_DTIM by SKIP_OVER_DTIM.
Add iwl_mvm prefix to a function name.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Current available FW still doesn't support new PM API.
Therefore, to enable basic power management with the
existing firmware, change the API in the driver back
to the API used in the current firmware.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When we roam to A band, we don't need to constraint WiFi
any more since it is operating on a different band.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This allows to have better wifi TPT when BT is active under
good RSSI conditions.
Wifi will have better chance to send Acks and Cts even if BT
is active.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use the per-interface debugfs infrastructure to create a
directory and symlink, and add a file containing debug
data related to each virtual interface.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This caused issues with tracing as it's longer than
the buffer size used there.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This module parameter isn't and won't be used. So ignore
its value and set BT_CH_ANNOUNCE unconditionally.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Schedule different time event based on the ROC type
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Increase the maximal remain on channel time as longer remain
on channel requests are handled by the FW using fragmented
time events.

This reduces the number of user/kernel space iterations during
flows such as p2p_listen. In addition it is currently required
for flows which require longer duration such as p2p_sd.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The RF-kill wakeup trigger flag is set in the wrong command,
which means it won't work. Also fix the comment in the TCP
wakeup trigger code -- the firmware was changed to look at
all the different trigger flags.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We should disable MIMO only if bt_traffic_load goes up to 3.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This is the right source of information for the valid Tx
antennas, not the NVM.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This data should taken from TLVs and not from the NVM. This
is true for the value written in CSR_HW_IF_CONFIG_REG too.

Also, no need to set the CSR_HW_IF_CONFIG_REG_BIT_MAC_SI bit
for 7000 devices which are the only devices currently
supported.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In firmware "listener" (monitor) mode, we still need to
open up the filters with the filter flags to receive all
frames.
Reviewed-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This has valuable data about RFkill state seen from the fw
side.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

5ghz_disable has no effect any longer, that was changed during
refactoring of EEPROM reading/parsing. Remove it, wpa_supplicant
allow now to specify frequencies, on which device will operate.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

1. Quota for the monitor interface should be added only if there is
   a channel context assigned to the interface.
2. In the unassign channel context flow, need to remove the quota
   for the monitor interface binding, before unbinding.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NAndrei Epure <epure.andrei@gmail.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This feature is not implemented yet in firmware.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The masks were wrong. They should be 0xffffffff when SCO,
HID or SNIFF profiles are used. They should be 0xffff0000
in any other case (default) to get a bit more throughput
when the BT profile allows for it.

Fix a debug print on the way.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Mostly for debugging purposes
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In AP mode, don't attempt to program GTKs into the
device, they're used for TX only so not needed and
programming them causes error messages. Also, in
this case and if key programming fails, avoid trying
to remove the key that isn't present later.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The code removed in this patch was used for bring up on
older NICs. No MVM capable fw will ever be released for
older NICs, so remove that code.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There are a number of situations in which mac80211 only
really needs to flush queues for one virtual interface,
and in fact during this frames might be transmitted on
other virtual interfaces. Calculate and pass a queue
bitmap to the driver so it knows which queues to flush.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The SCD byte count layout is decided by the configuration
done in fw, it is then logical to export it as a TLV flag
and not per HW SKU.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Fix a bug in writing to indirect (periphery) registers; although
writes seem successful the data is not written to the desired
address). Also fix address mask for HBUS_TARG_PRPH_RADDR and
HBUS_TARG_PRPH_WADDR registers.
Signed-off-by: NAmnon Paz <amnonX.paz@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This allows to test fw restart flow. The hook in transport
layer doesn't really make the fw assert. Moving this hook
to the op_mode allows to use the fw API to actually send a
host command that will make the fw assert.

Change the restart_fw module parameter to be a boolean on
the way.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The firmware tells the driver to what MACs the received frame
belongs (based on the time slot in which it was received).

Note that there can be several MACs if they share the same
binding.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This will allow to track how BT core updates the driver.
This is required to debug the BT Coexistence mechanism.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When BT traffic load gets higher, we want to avoid using the
shared antenna. In order to do so, we need to tell the AP
that we don't support MIMO any more, or at least not all
the time: in short, use the SMPS to achieve this.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The BT-Coex notification is sent by the fw when there are
updates wrt. BT activity. Driver action might be taken
based on the info in this notification.

For now, update the Ack/Cts_kill_msk if HID / SCO / A2DP
profiles are active.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Send the PRIO table before the calibrations. This table
tells the fw what priority to give to what (WiFi / BT)
according to events.

Send a hardcoded BT_COEX command to the fw to enable basic
BT coexistence.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This is the API to tell the fw to handle the BT Coexistence.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Then the transport can print it nicely in its debug prints.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If all the pieces of iwlwifi are built into the kernel
then there's no need for it to export its symbols to
other modules, so prevent that.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Now that we have two drivers (DVM and MVM) stop selecting
the DVM one (but make it default) and allow enabling only
the MVM driver if so desired. Add a warning for the case
of having neither DVM nor MVM enabled -- that's useless.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NDor Shaish <dor.shaish@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>