Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add support for the AVerMedia EZMaker PCI Deluxe and update the ivtv cardlist.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Manually fixed all pertinent checkpatch.pl errors inside the source code.

Also removed some unused code at the driver and a few minor cleanups.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

mv_count is a counter used to move the vertical bars. Before this patch, it
where a static var. This works fine for just one device. However, when using
multiple devices, every device would increment it.

This patch moves it to its correct place: struct vivi_dev. So, now, each device
has its own data.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Now, it is possible to open multiple vivi devices, by using n_devs parameter.
This makes vivi driver closer to a real one.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

There were a trouble at vivi driver when using non-zero inodes. This where due
to not properly preserving the minor inode after calling video_register. Since
this driver is a reference for newer drivers, and it is possible to have more
than one video device inside the machine, this patch makes vivi to dynamically
allocate video_device struct.

Thanks to Gregor Jasny <jasny@vidsoft.de> for pointing the issue.

Also, this patch removes a very anoying (but useless) message of not having a
proper release call.

CC: Gregor Jasny <jasny@vidsoft.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch enabled the IR remote control for the Avermedia M102 (card=110),
which appears to be the same IR as the already supported device on the
Avermedia AVerTV GO 007 FM (card=57) model, the code is two one liners which
enable the IR for this device (subsystem: 1461:f31e)
Signed-off-by: NAlbert Graham <agraham@g-b.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

dont just copy-and-paste stuff.
(compile-tested this time)
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Convert v4l from nopage to fault.
Remove redundant vma range checks.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The tuning request coming in from userspace is already center adjusted,
so we should not adjust to center (+1.75mhz) within the driver.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

cx25840_read4 reads a little-endian 32-bit value whereas cx25840_write4 writes
the 32-bit value as big-endian. Convert write4 to use little-endian as well
(that's the correct endianness).
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

After this patch, the order of the functions will be the same as before the
patch converting the driver to user video_ioctl2. This makes easier to diff
between the previous version and the newer one.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NDouglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Remove the shadowing 'struct v4l2_chip_ident *chip', since it already exists
and makes the if-statement useless.
Signed-off-by: NRichard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

converted debug module option to an or-able setting.

1 = info
2 = table map values
4 = register dumps
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Once the image rejection calibration procedure has been successful,
we should not initialize the tuner registers again.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

ivtv-yuv code clean up & reformat. Includes minor changes to some debug lines.

Also fixes a bug found during the reformatting, which would cause the
incorrect amount of yuv data to be sent to the card if source cropping
coordinates were used.

Apart from the bug-fix, there should be no functional difference to the
previous version.
Signed-off-by: NIan Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The driver was incorrectly reporting that it supported YUV 4:2:2 output, when
it is actually YUV 4:2:0. Though I believe the hardware can be pushed to
4:2:2, we don't currently support that.
Signed-off-by: NIan Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Previously, all yuv data written to /dev/video48 had only basic support with
no double buffering to avoid display tearing.

With this patch, yuv frames written to video48 are now handled by the existing
IVTV_IOC_DMA_FRAME framework. As such, the frames are hardware buffered to
avoid tearing, and honour scaling mode & field order options. Unlike the
proprietary IVTV_IOC_DMA_FRAME ioctl, all parameters are controlled by the
V4L2 API.

Due to mpeg & yuv output restrictions being different, their V4L2 output
controls have been separated. To control the yuv output, the V4L2 calls must
be done via video48.

If the ivtvfb module is loaded, there will be one side effect to this merge.
The yuv output window will be constrained to the visible framebuffer area. In
the event that a virtual framebuffer size is being used, the limit to the
output size will be the virtual dimensions, but only the portion that falls
within the currently visible area of the framebuffer will be shown.

Like the IVTV_IOC_DMA_FRAME ioctl, the supplied frames must be padded to 720
pixels wide. However the height must only be padded up the nearest multiple
of 32. This would mean an image of 102 lines must be padded to 128. As long
as the true source image size is given, the padding will not be visible in
the final output.
Signed-off-by: NIan Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Interlace mode selection code moved into the frame setup phase, so it's now
run before the frame is loaded into a hardware buffer. Given that it can
affect how a new frame is displayed, it was a bit stupid running it after the
frame was already visible.

A few stray interlace related variables which were linked to individual frames
have now been moved into the yuv_frame_info struct. This means that all
variables linked to a specific frame are in the same place & not scattered.

Minor code reformatting in areas touched by the above changes.
Signed-off-by: NIan Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

To reduce the number of display register accesses, the yuv code keeps track of
the current video settings. Should there be a change in any single parameter,
it will update the associated display registers to ensure everything is
displayed correctly.

The existing check also looks at the field order for the video. This is not
required, since field reversal does not require any display register changes.

This patch removes the field order from the check.
Signed-off-by: NIan Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>