btcx-risc is for the bt8xx driver and other drivers shouldn't depend
on it. There is no benefit to use that module just to do a
pci_zalloc_consistent.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Remove this function. This makes all vb2 queues behave the same, which
simplifies comparing the various vb2 queue op implementations.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

As usual, this patch is very large due to the fact that half a vb2 conversion
isn't possible. And since this affects blackbird, alsa, core, dvb, vbi and
video the changes are all over.

What made this more difficult was the peculiar way the risc program was setup.
The driver allowed for running out of buffers in which case the DMA would stop
and restart when the next buffer was queued. There was also a complicated
timeout system for when buffers weren't filled. This was replaced by a much
simpler scheme where there is always one buffer around and the DMA will just
cycle that buffer until a new buffer is queued. In that case the previous
buffer will be chained to the new buffer. An interrupt is generated at the
start of the new buffer telling the driver that the previous buffer can be
passed on to userspace.

Much simpler and more robust.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Hauppauge Nova-S-Plus DVB-S model 92001 does not lock on horizontal
polarisation. According with the info provided at the BZ, model
92002 does.

The difference is that, on model 92001, the tone select is done via
isl6421, while, on other devices, this is done via cx24123 code.
This patch adds a way to override the demod's set_tone at isl6421
driver. In order to avoid regressions, the override is enabled
only for cx88 Nova S plus model 92001. For all other models and
devices, the set_tone is provided by the demod driver.

Patch originally proposed at bz@9476[1] by Michel Meyers and
John Donoghue but applying the original patch would break support
for all other devices based on isl6421.

[1] https://bugzilla.kernel.org/show_bug.cgi?id=9476Tested-by: NAdam Sampson <ats@offog.org>
Tested-by: NHans-Peter Jansen <hpj@urpla.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch introduces the use of IS_ENABLED() macro. For example,
replacing:
 #if defined(CONFIG_I2C) || (defined(CONFIG_I2C_MODULE) && defined(MODULE))
with:
 #if IS_ENABLED(CONFIG_I2C)
All changes made by this patch respect the same replacement pattern.
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Acked-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Tuner part of Montage rs2000 chip is similar to ts2020 tuner.
Patch to use ts2020 code.

[mchehab@redhat.com: a few CodingStyle fixes]
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

make the other drivers take use of the separate ts2020 driver
Signed-off-by: NKonstantin Dimitrov <kosio.dimitrov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r1@
statement S;
position p,p1;
@@
S@p1;@p
@script:python r2@
p << r1.p;
p1 << r1.p1;
@@
if p[0].line != p1[0].line_end:
        cocci.include_match(False)
@@
position r1.p;
@@
-;@p
// </smpl>

[mchehab@redhat.com: some hunks got bitroted; applied only the
 ones that succeeds]
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
[crope@iki.fi: For my drivers a8293, af9013, af9015, af9035]
Acked-by: NAntti Palosaari <crope@iki.fi>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Rename all PCI drivers with their own directory under
drivers/media/video into drivers/media/pci and update the
building system.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This callback were meant to allow overriding a FE callback, before its
call, but it is not really needed, as the callback can be intercepted
after tuner attachment.

Worse than that, only DVBv3 calls are intercepted this way, so a DVBv5
application will produce different effects than a DVBv3 one.

So, get rid of it.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: NAntti Palosaari <crope@iki.fi>
Reviewed-by: NAntti Palosaari <crope@iki.fi>

Leadtek DTV2000H J has Philips a FMD1216MEX tuner,
and not a FMD1216ME.
Signed-off-by: NMiroslav Slugen <thunder.mmm@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is a big patch, yet trivial: now that all tuners use the DVBv5
way to pass parameters (e. g. via fe->dtv_property_cache), the
extra parameter can be removed from set_params() call.

After this change, very few DVBv3 specific stuff are left at the
tuners.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Instead of using DVBv3 parameters, rely on DVBv5 parameters to
set the tuner
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

dvb_register calls videobuf_dvb_register_bus, but if that returns
a failure the module will be unloaded without clearing the
value of core->gate_ctrl which will cause an oops in macros
called from video_open in cx88-video.c
Signed-off-by: NDavid Fries <David@Fries.net>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Istvan Varga <istvan_v@mailbox.hu>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

All the modified drivers didn't have any version increment since
Jan, 1 2011. Several of them didn't have any version increment
for a long time, even having new features and important bug fixes
happening.

As we're now filling the QUERYCAP version with the current Kernel
Release, we don't need to maintain a per-driver version control
anymore. So, let's just use the default.

In order to preserve the Kernel module version history, a
KERNEL_VERSION() macro were added to all modified drivers, and
the extraver number were incremented.

I opted to preserve the per-driver version control to a few
pwc, pvrusb2, s2255, s5p-fimc and sh_vou.

A few drivers are still using the legacy way to handle ioctl's.
So, we can't do such change on them, otherwise, they'll break.
Those are: uvc, et61x251 and sn9c102.

The rationale is that the per-driver version control seems to be
actively maintained on those.

Yet, I think that the better for them would be to just use the
default version numbering, instead of doing that by themselves.

While here, removed a few uneeded include linux/version.h
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch implements support for the Leadtek WinFast DTV1800 H card with
XC4000 tuner (107d:6f38).
Signed-off-by: NIstvan Varga <istvan_v@mailbox.hu>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch implements support for the Leadtek WinFast DTV2000 H Plus card
with XC4000 tuner (107d:6f42).
Signed-off-by: NIstvan Varga <istvan_v@mailbox.hu>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Added functions for XC4000 tuner reset and attaching DVB frontend.
Signed-off-by: NIstvan Varga <istvan_v@mailbox.hu>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The BKL conversion of this driver seems to have gone wrong.
Loading the cx88-blackbird driver deadlocks.

The cause: mpeg_ops::open in the cx2388x blackbird driver acquires the
device lock and calls the sub-driver's request_acquire, which tries to
acquire the lock again.  Fix it by clarifying the semantics of
request_acquire, request_release, advise_acquire, and advise_release:
now all will rely on the caller to acquire the device lock.

Based on work by Ben Hutchings <ben@decadent.org.uk>.

Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=31962Reported-by: NAndi Huber <hobrom@gmx.at>
Tested-by: NAndi Huber <hobrom@gmx.at>
Tested-by: NMarlon de Boer <marlon@hyves.nl>
Cc: stable@kernel.org
Signed-off-by: NJonathan Nieder <jrnieder@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The BKL conversion of this driver seems to have gone wrong.  Various
uses of the sub-device and driver lists appear to be subject to race
conditions.

In particular, some functions access drvlist without a relevant lock
held, which will race against removal of drivers.  Let's start with
that --- clean up by consistently protecting dev->drvlist with
dev->core->lock, noting driver functions that require the device lock
to be held or not to be held.

After this patch, there are still some races --- e.g.,
cx8802_blackbird_remove can run between the time the blackbird driver
is acquired and the time it is used in mpeg_release, and there's a
similar race in cx88_dvb_bus_ctrl.  Later patches will address the
remaining known races and the deadlock noticed by Andi.  This patch
just makes the semantics clearer in preparation for those later
changes.

Based on work by Ben Hutchings <ben@decadent.org.uk>.
Tested-by: NAndi Huber <hobrom@gmx.at>
Tested-by: NMarlon de Boer <marlon@hyves.nl>
Cc: stable@kernel.org
Signed-off-by: NJonathan Nieder <jrnieder@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The card uses ds3000 demod from Montage.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A Hauppauge HVR 4000 is used on a School On Internet Asia (SOI Asia)
project in order to carry IP traffic over ULE. However, there is an
issue with high latency jitter.

My boss, Husni, identified the problem and provided a patch for it.

The default buffer size of 32 TS frames on cx88 causes the high latency,
so our deployment changes that to 6 TS frames. This patch made the
buffer size tunable, while keeping the default buffer size of 32 TS
frames unchanged.
Signed-off-by: NAchmad Husni Thamrin <husni@ai3.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Patch add support of TwinHan 1027 DVB-S card.

Refreshed version of https://patchwork.kernel.org/patch/79753/ patch.
(adapted for the new IR system), still works.

DVB-S support come from a patch originally authored by
Manu Abraham (abraham.manu@gmail.com).
IR Port support were added by Sergey.

Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add an ext_lock argument to the videobuf init functions. This allows
drivers to pass the vdev->lock pointer (or any other externally held lock)
to videobuf. For now all drivers just pass NULL.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Making static data const avoids allocation of additional r/w memory and
reduces initialisation time.  It also provides some additional opportunities
for compiler optimisations.
Signed-off-by: NLawrence Rust <lvr@softsystem.co.uk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

[dougsland@redhat.com: fixed reject due changes in cx88-dvb.c]
Signed-off-by: NRicardo Maraschini <ricardo.maraschini@gmail.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is not needed, since the function already do it. Also, it causes
a warning at the compilation, since a new var is declared in the middle
of the code.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds support for the built-in dvb device
of a Samsung SMT7020s (x86 based STB) to the cx88 family.
Signed-off-by: NDirk Herrendoerfer <d.herrendoerfer@herrendoerfer.name>
Signed-off-by: NHelmut Auer <helmut@helmutauer.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add Prof 7301 PCI DVB-S2 card

The card based on stv0903 demod, stb6100 tuner.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Upcoming I2C v4l2_subdev drivers need a way to control the subdevice
power state from the core. This use case is already partially covered by
the tuner s_standby operation, but no way to explicitly come back from
the standby state is available.

Rename the tuner s_standby operation to core s_power, and fix tuner
drivers accordingly. The tuner core will call s_power(0) instead of
s_standby(). No explicit call to s_power(1) is required for tuners as
they are supposed to wake up from standby automatically.

[mchehab@redhat.com: CodingStyle fix]
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Trivial patch which adds the __init and __exit macros to the module_init /
module_exit functions to several files in drivers/media/video/cx88/
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

It were using 7 spaces instead of tab for indent.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It does matter to set explicitly gpio0 value in
cx88_board structure for TBS 8920 card.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I updated and simplyfied patch from Zbynek Hrabovsky for recent kernel.
It enables autodetection of card, sound in analog TV , sound in FM radio
and switching between antenna and cable RF input.  Radio tuner still
doesn't work, I don't even know how it works.  Some guys wrote me that FM
radio works with TV tuner used instead of radio part (symlink video0 ->
radio0).

Cc: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: NVlastimil Labsky <vlasta.labsky@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The introduction of the zl10353 i2c gate control broke support for the
Geniatech board (which is not behind an i2 gate).  Add the needed parameter.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Enables analog/digital tv, radio and remote control (gpio).
Tested-by: NMarcin Wojcikowski <emtees.mts@gmail.com>
Tested-by: NKarel Juhanak <karel.juhanak@warnet.cz>
Tested-by: NAndrew Goff <goffa72@gmail.com>
Tested-by: NJan Novak <novak-j@seznam.cz>
Signed-off-by: NMiroslav Sustek <sustmidown@centrum.cz>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

s_standby is only used to put the tuner in powersaving mode, so move it
from core to tuner.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert cx88 to use v4l2_subdev since the old i2c autoprobing mechanism
will be removed.

Added code to explicitly load tvaudio where needed. Also fix the rtc-isl1208
support: since that driver no longer supports autoprobing it has to be
loaded using the new i2c API.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds support for Terratec Cinergy HT PCI MKII with card id 79.
Its more or less a copy of Pinnacle Hybrid PCTV.
Thanks to k1ngf1sher on forum.ubuntuusers.de for the idea to copy that card.
Signed-off-by: NStephan Wienczny <stephan@wienczny.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>