There is no need to do software reset on init() as it is done a bit
later on end of set_frontend(). Software reset usually means
restarting (resetting to starting point) chip internal state machine
(FSM). Naturally it is done after all parameters are programmed.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Enable regmap register cache in order to reduce IO.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

RTL2832 demod integrated into RTL2832U has PID filter. PID filtering
is provided by rtl2832 demod driver. Add support for it.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Implement PID filter. This demod has PID filter size of 32 PIDs.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Demod lock flags are derived from demod state machine states. States
are running from 1 to 11, where highest state 11 means demod is
fully locked and streaming. Naturally smaller state numbers means
there is some partial locks.

Define now state 10 as missing synch and lock.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

We don't need it anymore as all users are using muxed I2C adapter.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Tuners are connected to demod I2C adapter. Use that muxed adapter
for each tuner. That allows us to get rid of hackish FE gate control
solution.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Estimate signal strength from IF digital AGC.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Change legacy DVBv3 read BER to return values calculated by DVBv5
statistics.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Change legacy DVBv3 read SNR to return values calculated by DVBv5
statistics.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

DVBv5 BER.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

DVBv5 CNR.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Use regmap to cover register access routines.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Use platform data configuration for rtl2832 demod driver. Old
configuration are still left as it is used for rtl2832_sdr driver.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Move all needed configuration values to platform data structure
and remove old configuration code where possible.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Pass correct device pointer to dev_* logging functions in order
print logs correctly.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Rename it device state variable to dev. Both priv and dev are very
common terms for such variable in kernel, but I like use dev in
order to keep drivers consistent.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Exported resources are not needed anymore as all users are using
callbacks carried via platform data. Due to that we will remove
those.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Switch demod resource use from exported symbols to callbacks its
provides.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Add callback for all of those functions which are currently
exported using EXPORT_SYMBOL. That allows us convert every user to
callbacks and eventually all exported symbols could be removed.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Use regmap to cover register access routines.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Own I2C locking is needed due to two special reasons:
1) Chips uses multiple register pages/banks on single I2C slave.
Page is changed via I2C register access.
2) Chip offers muxed/gated I2C adapter for tuner. Gate/mux is
controlled by I2C register access.

Due to these reasons, I2C locking did not fit very well.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

RTL2830 demod integrated to RTL2831U has PID filter. PID filtering
is provided by rtl2830 demod driver. Add support for it.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Implement PID filter.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Change legacy DVBv3 read SNR to return values calculated by DVBv5
statistics.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Change legacy DVBv3 read BER to return values calculated by DVBv5
statistics.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Change legacy DVBv3 signal strength to return values calculated by
DVBv5 statistics.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

DVBv5 BER.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Estimate signal strength from IF AGC.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

DVBv5 CNR.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Trivial changes proposed by checkpatch.pl and some more.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Remove internal config and use configuration values directly from
the platform data.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Pass correct device for dev_foo() logging in order to print logs
correctly.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

As a I2C driver struct i2c_client is top level structure representing
the driver. Use it as parameter to carry all needed information for
each function in order to simplify things.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Use name 'dev' for device state instance as it is more common and
also one letter shorter.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Remove legacy DVB binding as all users are using I2C binding.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

rtl2830 driver supports now I2C model too. Start using it.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Convert driver to kernel I2C model. Old DVB proprietary model is
still left there also.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Top level pointer on USB probe is struct usb_interface *. Add that
pointer to struct dvb_usb_device that drivers could use it, for
dev_* logging and more.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Although IRQ_HANDLED is "safe" value to return,
it is better to let the kernel know whether the driver handle the interrupt or not.
Signed-off-by: NNibble Max <nibble.max@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>