Add a new pipe config check macro PIPE_CONF_CHECK_CLOCK_FUZZY() to make
it trivial and error proof to compare clocks in a fuzzy manner.

v2: Drop extra curly braces
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that adjusted_mode.clock no longer contains the pixel_multiplier, we
can kill the get_clock() callback and instead do the clock readout
in get_pipe_config().

Also i9xx_crtc_clock_get() can now extract the frequency of the PCH
DPLL, so use it to populate port_clock accurately for PCH encoders.
For DP in port A the encoder is still responsible for filling in
port_clock. The FDI adjusted_mode.clock extraction is kept in place
for some extra sanity checking, but we no longer need to pretend it's
also the port_clock.

In the encoder get_config() functions fill out adjusted_mode.clock
based on port_clock and other details such as the DP M/N values,
HDMI 12bpc and SDVO pixel_multiplier. For PCH encoders we will then
do an extra sanity check to make sure the dotclock we derived from
the FDI configuratiuon matches the one we derive from port_clock.

DVO doesn't exist on PCH platforms, so it doesn't need to anything
but assign adjusted_mode.clock=port_clock. And DDI is HSW only, so
none of the changes apply there.

v2: Use hdmi_reg color format to detect 12bpc HDMI case
v3: Set adjusted_mode.clock for LVDS too
v4: Rename ironlake_crtc_clock_get to ironlake_pch_clock_get,
    eliminate the useless link_freq variable.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add the 120MHz refernce clock case for PCH DPLLs.

Also determine the reference clock frequency more accurately by
checking for the PLLB_REF_INPUT_SPREADSPECTRUMIN refclk input
mode. The gen2 code already checked it, but it stil assumed a
fixed 66MHz refclk. Instead we need to consult the VBT for the
real value.

v2: Fix refclk for SSC panel case
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We already extract the DPLL state to pipe_config, so let's make use of
it in i9xx_crtc_clock_get() and avoid the register reads.

This will also make the function closer to being useable with PCH DPLL
since the registers for those live in a different address.

Also kill the useless adjusted_mode.clock zeroing. It's already zero at
this point.

v2: Read out DPLL state in intel_crtc_mode_get()
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Extract the code to calculate the dotclock from the link clock and M/N
values into a new function from ironlake_crtc_clock_get().

The new function can be used to calculate the dotclock for both FDI and
DP cases.

Also simplify the code a bit along the way.

v2: Don't forget about non-pch encoders in ironlake_crtc_clock_get()
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The cursor is supposed to be disabled during crtc mode set (disabled by
ctrc disable). Assert this is the case.

v2: move cursor disabled assert next to plane asserts (Ville)
Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We want to do fuzzy clock checks for other things besides
adjusted_mode.clock, so just pass two two clocks to compare
to intel_fuzzy_clock_check().
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add functions to read out the CPU and PCH transcoder M/N values,
and use them to fill out the pipe config dp_m_n information. And
while at it populate has_dp_encoder too.

Also refactor ironlake_get_fdi_m_n_config() to simply call the new
intel_cpu_transcoder_get_m_n() function.

v2: Remember the DDI
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On CTG+ read out the pipe bpp setting from hardware and fill it into
pipe config. Also check it appropriately.

v2: Don't do the pipe_bpp extraction inside the PCH only code block on
    ILK+.
    Avoid the PIPECONF read as we already have read it for the
    PIPECONF_EANBLE check.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It would be easier if adjusted_mode.clock would be the pipe pixel clock,
and it actually is, except for the cases where pixel_multiplier > 1.

So let's change intel_sdvo to use port_clock as the multiplied clock,
and then we can leave adjusted_mode.clock as pipe pixel clock.

v2: Improve port_clock documentation
    Rebased on top of SDVO pixel_multiplier fixes
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We feed the non-multiplied clock to intel_link_compute_m_n(), so the
opposite operation should use the same order of operations. So we just
multiply by pixel_multiplier in the end now.
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Ignoring the legacy DRI1 code, and a couple of special cases (to be
discussed later), all access to the ring is mediated through requests.
The first write to a ring will grab a seqno and mark the ring as having
an outstanding_lazy_request. Either through explicitly adding a request
after an execbuffer or through an implicit wait (either by the CPU or by
a semaphore), that sequence of writes will be terminated with a request.
So we can ellide all the intervening writes to the tail register and
send the entire command stream to the GPU at once. This will reduce the
number of *serialising* writes to the tail register by a factor or 3-5
times (depending upon architecture and number of workarounds, context
switches, etc involved). This becomes even more noticeable when the
register write is overloaded with a number of debugging tools. The
astute reader will wonder if it is then possible to overflow the ring
with a single command. It is not. When we start a command sequence to
the ring, we check for available space and issue a wait in case we have
not. The ring wait will in this case be forced to flush the outstanding
register write and then poll the ACTHD for sufficient space to continue.

The exception to the rule where everything is inside a request are a few
initialisation cases where we may want to write GPU commands via the CS
before userspace wakes up and page flips.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Make the call to intel_update_watermarks() just once or twice during
modeset. Ideally it should happen independently when each plane gets
enabled/disabled, but for now it seems better to keep it in central
place. We can improve things when we get all the planes sorted out
in a better way.

When enabling set up the watermarks just before the pipe is enabled.
And when disabling we need to wait until we've marked the crtc as
inactive, as otherwise intel_crtc_active() would still think the pipe
is enabled and the computed watermarks would reflect that.

v2: Pimp up the commit message a bit
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Passing the appropriate crtc to intel_update_watermarks() should help
in avoiding needless work in the future.

v2: Avoid clash with internal 'crtc' variable in some wm functions
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The patch doesn't contain functional change, but is to prepare for
future platform which has different DPIO phy.  The additional pipe
parameter will use to select which phy to target for.

v2: Update the commit message and add static for the new function.
(Jani/Ville)
Signed-off-by: NChon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Acked-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

ironlake_fdi_compute_config() already checks that we have enough
FDI bandwidth. And it doesn't just use a hardcoded value but takes
into account factors such as the actual FDI frequency, shared FDI
B/C lanes, etc.
Suggested-by: NDaniel Vetter <daniel@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For DP pll settings, there is only two golden configs.  Instead of
running through the algorithm to determine it, hardcode the value and get it
determine in intel_dp_set_clock.

v2: Rework on the intel_limit compiler warning. (Jani)
Signed-off-by: NChon Ming Lee <chon.ming.lee@intel.com>
[danvet: Fix up checkpatch issues.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The spec says to notify prior to power down and after power up. It is
unclear whether it makes a difference.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

DPLL is not needed for DSI

v2: Rebase due to added DSI PLL assertion patch.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For DSI, we need to be asserting DSI PLL, not DPLL.

This is a somewhat stopgap implementation. It's slightly ugly to have to
pass the dsi parameter to intel_enable_pipe().
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The dpll actually runs at the port clock so we don't need
to multiply it again with the pixel multiplier to get the
adjusted_mode.clock. This is in contrast to the ironlake
pixel clock readout code which uses the fdi dotclock: That
one does _not_ run with multiplied pixels.

This issue goes back to the original clock readout code added
in

commit f1f644dc
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Thu Jun 27 00:39:25 2013 +0300

    drm/i915: get mode clock when reading the pipe config v9

Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is intended to add VGA arbiter support for Intel HD graphics on
Core processors.  The old GMCH registers no longer exist, so even
though it appears that i915 participates in VGA arbitration, it doesn't
work.  On Intel HD graphics we already attempt to disable VGA regions
of the device.  This makes registering as a VGA client unnecessary since
we don't intend to operate differently depending on how many VGA devices
are present.  We can disable VGA memory regions by clearing the memory
enable bit in the VGA MSR.  That only leaves VGA IO, which we update
the VGA arbiter to know that we don't participate in VGA memory
arbitration.  We also add a hook on unload to re-enable memory and
reinstate VGA memory arbitration.

v3: Use explicit LEGACY_IO | LEGACY_MEM when restoring rather than
    LEGACY_MASK, per Ville's comments.

v2: I915_READ/WRITE accessors don't work in i915_disable_vga, use inb/outb
    directly.  Also, on the driver unbind VGA enable path, acquire legacy
    IO to re-enable VGA memory.  Correct comment.
Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add patch changelog. Also squash in a fixup to have a dummy
static inline for vga_set_legacy_decoding for CONFIG_VGA_ARB=n as
reported by the 0-day kernel build bot.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

fixup 2

We shouldn't disable the trickle feed bits on Haswell. Our
documentation explicitly says the trickle feed bits of PRI_CTL and
CUR_CTL should not be programmed to 1, and the hardware engineer also
asked us to not program the SPR_CTL field to 1. Leaving the bits as 1
could cause underflows.
Reported-by: NArthur Runyan <arthur.j.runyan@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

RCS flips do work on Iybridge+ so long as we can unmask the messages
through DERRMR. However, there are quite a few workarounds mentioned
regarding unmasking more than one event or triggering more than one
message through DERRMR. Those workarounds in principle prevent us from
performing pipelined flips (and asynchronous flips across multiple
planes) and equally apply to the "known good" BCS ring. Given that it
already appears to work, and also appears to work with unmasking all 3
planes at once (and queuing flips across multiple planes), be brave.

Bugzlla: https://bugs.freedesktop.org/show_bug.cgi?id=67600Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Lightly-tested-by: NStephane Marchesin <marchesin@icps.u-strasbg.fr>
Cc: Stephane Marchesin <marchesin@icps.u-strasbg.fr>
Cc: Ben Widawsky <ben@bwidawsk.net>
Tested-by: NStéphane Marchesin <marcheu@chromium.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This lets drivers see the flags requested by the application

[airlied: fixup for rcar/imx/msm]
Signed-off-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NDave Airlie <airlied@gmail.com>

If we don't use the return value of a mmio read our coding style is to
use the POSTING_READ macro. This avoids cluttering the mmio traces.

While at it add the missing posting read in the lcpll enable function
that Paulo spotted.

v2: Drop the _NOTRACE changes, tracing such wait_for loops in the modeset
code might actually be rather useful!

Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We currently only enter PC8+ after all its required conditions are
met, there's no rendering, and we stay like that for at least 5
seconds.

I chose "5 seconds" because this value is conservative and won't make
us enter/leave PC8+ thousands of times after the screen is off: some
desktop environments have applications that wake up and do rendering
every 1-3 seconds, even when the screen is off and the machine is
completely idle.

But when I was testing my PC8+ patches I set the default value to
100ms so I could use the bad-behaving desktop environments to
stress-test my patches. I also thought it would be a good idea to ask
our power management team to test different values, but I'm pretty
sure they would ask me for an easy way to change the timeout. So to
help these 2 cases I decided to create an option that would make it
easier to change the default value. I also expect people making
specific products that use our driver could try to find the perfect
timeout for them.

Anyway, fixing the bad-behaving applications will always lead to
better power savings than just changing the timeout value: you need to
stop waking the Kernel, not quickly put it back to sleep again after
you wake it for nothing. Bad sleep leads to bad mood!
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch allows PC8+ states on Haswell. These states can only be
reached when all the display outputs are disabled, and they allow some
more power savings.

The fact that the graphics device is allowing PC8+ doesn't mean that
the machine will actually enter PC8+: all the other devices also need
to allow PC8+.

For now this option is disabled by default. You need i915.allow_pc8=1
if you want it.

This patch adds a big comment inside i915_drv.h explaining how it
works and how it tracks things. Read it.

v2: (this is not really v2, many previous versions were already sent,
     but they had different names)
    - Use the new functions to enable/disable GTIMR and GEN6_PMIMR
    - Rename almost all variables and functions to names suggested by
      Chris
    - More WARNs on the IRQ handling code
    - Also disable PC8 when there's GPU work to do (thanks to Ben for
      the help on this), so apps can run caster
    - Enable PC8 on a delayed work function that is delayed for 5
      seconds. This makes sure we only enable PC8+ if we're really
      idle
    - Make sure we're not in PC8+ when suspending
v3: - WARN if IRQs are disabled on __wait_seqno
    - Replace some DRM_ERRORs with WARNs
    - Fix calls to restore GT and PM interrupts
    - Use intel_mark_busy instead of intel_ring_advance to disable PC8
v4: - Use the force_wake, Luke!
v5: - Remove the "IIR is not zero" WARNs
    - Move the force_wake chunk to its own patch
    - Only restore what's missing from RC6, not everything
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This was causing WARNs in one machine, so instead of trying to guess
exactly which hotplug bits should exist, just do the test on the
non-HPD bits. We don't care about the state of the hotplug bits, we
just care about the others, that need to be 1.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If LCPLL is disabled, there's a chance we might be in package C8 state
or deeper, and we'll get a hard hang when restoring LCPLL (also, a red
led lights up on my motherboard). So grab the force_wake, which will
get us out of RC6 and, as a consequence, out of PC8+ (since we need
RC6 to get into PC8+).

Note: Discussions with hw designers are still ongoing what exactly
goes boom here. But I think we can go ahead and just merge this little
hack for now until it's clear what we actually need.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Add small note about the current state of the discussion
around this hack.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The existing code was trying different vswing and preemphasis settings
in the wrong place, and wasn't trying them enough.  So add a loop to
walk through them, properly disabling FDI TX and RX in between if a
failure is detected.

v2: remove unneeded reg writes, add delays around bit lock checks (Jesse)
v3: fix TX and RX disable per spec (Paulo)
    fix delays per spec (Paulo)
    make RX symbol lock check match TX bit lock check (Paulo)
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51983Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Whenever I need to work with the HSW_PWER_WELL_* register bits I have
to look at the documentation to find out which bit is to request the
power well and which one shows its current state. Rename the bits so I
won't need to look the docs every time.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If the power well is disabled VGA is guaranteed to be disabled.

This fixes unclaimed register messages that happen on suspend/resume.

v2: Check the actual hw power well state instead of our own tracking
to make sure VGA is _really_ off (in case the BIOS/KVMr has just its
own request bit set). Requested by Ville.

Note: Ville suggested whether it wouldn't be better to just enable the
power well over a slightly longer time in our resume code, since we
already do that. I tend to agree, but there's also the modeset force
code in the lid notifier which _also_ eventually calls redisable_vga.
We shouldn't ever need this on somewhat modern hw (everything with
opregion essentially) but the code to bail out isn't there. Hence
stick with this simple approach here for now.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67517Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Summarize the discussion around the resume sequence and lid
notifier a bit.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

After computing the stage changes for the set_config, record those in
the debug log.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Caught by "make W=1 drivers/gpu/drm/i915/".
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we get an error event really early in the driver setup sequence,
which gen3 is especially prone to with various display GTT faults we
Oops. So try to avoid this.

Additionally with Haswell the transcoders are a separate bank of
registers from the pipes (4 transcoders, 3 pipes). In event of an
error, we want to be sure we have a complete and accurate picture of
the machine state, so record all the transcoders in addition to all
the active pipes.

This regression has been introduced in

commit 702e7a56
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date:   Tue Oct 23 18:29:59 2012 -0200

    drm/i915: convert PIPECONF to use transcoder instead of pipe

Based on the patch "drm/i915: Dump all transcoder registers on error"
from Chris Wilson:

v2: Rebase so that we don't try to be clever and try to figure out the
cpu transcoder from hw state. That exercise should be done when we
analyze the error state offline.

The actual bugfix is to not call intel_pipe_to_cpu_transcoder in the
error state capture code in case the pipes aren't fully set up yet.

v3: Simplifiy the err->num_transcoders computation a bit. While at it
make the error capture stuff save on systems without a display block.

v4: Fix fail, spotted by Jani.

v5: Completely new commit message, cc: stable.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60021
Cc: stable@vger.kernel.org
Tested-by: NDustin King <daking@rescomp.stanford.edu>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The display engine has unique coherency rules such that it requires
special handling to ensure that all writes to cursors, scanouts and
sprites are clflushed. This patch introduces the infrastructure to
simply track when an object is being accessed by the display engine.

v2: Explain the is_pin_display() magic as the sources for obj->pin_count
and their individual rules is not obvious. (Ville)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Ryan noticed that on his board, HDMI was wired up to port C but not
exposed by the kernel, which had only expected DP on that port.  Fix
that up by enumerating both ports if possible.
Tested-by: N"Matsumura, Ryan" <ryan.matsumura@intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Fix up the whitespace fail. Tsk.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>