Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSangtae Ha <sha2@ncsu.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new SCTP socket api (draft 16) updates the AUTH API structures.
We never exported these since we knew they would change.
Update the rest to match the draft.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>

The chunks are stored inside a parameter structure in the kernel
and when we copy them to the user, we need to account for
the parameter header.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>

I noticed while looking into some odd behavior in sctp, that the variable
name sctp_pf_inet6_specific was used twice to represent two different
pieces of data (its both a structure name and a pointer to that type of
structure), which is confusing to say the least, and potentially dangerous
depending on the variable scope.  This patch cleans that up, and makes the
protocol and address family registration names in SCTP more regular,
increasing readability.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>

 ipv6.c     |   12 ++++++------
 protocol.c |   12 ++++++------
 2 files changed, 12 insertions(+), 12 deletions(-)

As Davem mentioned in his recently patch
(d9595a7b)
that the procfs visibility should occur after
the ->proc_fops are setup.

And also, Alexey provide proc_create() to make
sure that ->proc_fops is setup before gluing PDE
to main tree.

We use proc_create().
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several endianity corrections in start_xmit()

Fixed TSO bug where packets were missing the TCP flags.
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Limit traffic through an internal queue to prevent overflow.
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed locking between fastpath and slowpath operations.

Corrected order of traffic disabling to prevent race when going down
under traffic.

- first have the microcode drop all incoming packets
- then do the slowpath stuff
- only then reset the MAC

Got rid of in_reset_task.

Remove_one() and friends would deference a null pointer if init_one
failed.
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of the HW attentions, used to indicate an error were not properly
acked.

This will cause the driver to endlessly receive interrupts when such
an error happens.

Had to break the code into smaller chunks because it got too nested.
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Errata A0.158 workaround. 

Running in INT#A mode after running with MSI-X fails due to a PCI core
bug.
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Errors were summed improperly, some stats were missing.
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The configuration of RX filtering needed the following corrections:

Drop flags need to be set per Rx queue.

Have to tell the microcode to collect drop stats, and properly wait
for them to complete when going down.

Sometimes we failed to detect proper completion due to a logical error
in the wait loop.
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Properly protect PHY access between two devices on the same board with
a HW lock.

Use GPIO to clear all previous configurations before changing link
parameters.

Shut down the external PHY in case of fan failure.

Reducing the MDC/MDIO clock to 2.5MHz due to problems with some
devices.

Resolve the flow control response according to autoneg with external
PHY.

Unmasking all PHY interrupts in single write to prevent a race in the
interrupts order.

LASI indication fixes to work with peculiarities of PHYs.

Disable MAC RX to avoid a HW bug when closing the MAC under traffic.

Disable parallel detection on HiGig due to HW limitation.

Updating the shared memory structure to work with the current
bootcode.
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct PCI-E info printed by init_one()
In one case it failed to free the netdev. 
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because we use shared tfm objects in order to conserve memory,
(each tfm requires 128K of vmalloc memory), BH needs to be turned
off on output as that can occur in process context.

Previously this was done implicitly by the xfrm output code.
That was lost when it became lockless.  So we need to add the
BH disabling to IPComp directly.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch the SSB PCI core driver to the new SPROM data structure now that
the old one has been removed.
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Acked-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This may happen e.g. when the ssb is statically enables by the b44 driver,
and the b43 pci-ssb bridge is enbled by the b43/b43legacy drivers, or the
b43/b43legacy drivers are built statically.
Signed-off-by: NAlexey Zaytsev <alexey.zaytsev@gmail.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The bridge code was unnecessary enabled by the b44
driver, but it prevents the bcm43xx driver from
being loaded, as the bridge claims the same pci ids.

Now we enable the birdge only if the b43{legacy}
drivers are selected.
Signed-off-by: NAlexey Zaytsev <alexey.zaytsev@gmail.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The libertas driver exports a number of symbols with no in-tree users;
remove these unused exports.  lbs_reset_device() is completely unused, with
no callers at all, so remove the function completely.

A couple of these unused exported symbols are static, which causes the
following build error on ia64 with gcc 4.2.3:

    drivers/net/wireless/libertas/main.c:1375: error: __ksymtab_lbs_remove_mesh causes a section type conflict
    drivers/net/wireless/libertas/main.c:1354: error: __ksymtab_lbs_add_mesh causes a section type conflict
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Acked-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The "goto end;" part definitely must not be rate limited.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00lib_reset_link_tuner() can be called from within
the link tuner itself. This means that it should
_not_ call rt2x00lib_stop_link_tuner() since that will
cause the thread to hang.

Reorder the things that should be done during a
link tuner reset and during a link tuner start.

Also make antenna tuning the last step of the link
tuner since it could possibly reset some statistical
information which we need for average calculation.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When rssi_a > rssi_b is true and the current antenna
was already antenna A, then rt2x00 incorrectly jumped
to antenna B.

Also don't configure the antenna when there has been
no change in the antenna setup.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>