Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NJens Axboe <axboe@carl.home.kernel.dk>

Mark the m68knommu memory init functions as __init.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Mark the m68knommu setup_arch() function as __init.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Removed header includes not needed.
Remove use of old m68knommu timer function pointers.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Clean up 68EZ328 timer support code. Removed header includes not needed.
Remove use of old m68knommu timer function pointers.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Clean up 68360 timer support code. Removed header includes not needed.
Remove use of old m68knommu timer function pointers. Use common function
naming for 68328 timer functions.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use common function naming for 68328 timer functions to make them
consistent with the various other hardware m68knommu timers.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Clean up 68328 timer support code. Removed header includes not needed.
Remove use of old m68knommu timer function pointers.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove unused variables from setup.c code.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Rather than hand-rolling our own prototype, make the code more
future-proof by using the standard irq_handler_t typedef.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add support to force_hpet for all known MCP55 (nForce 5) chipset
LPC bridges.

These are the untested nForce 5 chips (taken from Mikko's original 
patch, and checked against pci.ids).
Signed-off-by: NCarlos Corbacho <cathectic@gmail.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

 arch/x86/kernel/quirks.c |   18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

This patch adds a quirk from LinuxBIOS to force enable HPET on
the nVidia CK804 (nForce 4) chipset.

This quirk can very likely support more than just nForce 4
(LinuxBIOS use the same code for nForce 5), and possibly nForce 3,
but I don't have those chipsets, so cannot add and test them.

Tested on an Abit KN9 (CK804).
Signed-off-by: NCarlos Corbacho <cathectic@gmail.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

 Documentation/kernel-parameters.txt |    3 +-
 arch/x86/kernel/quirks.c            |   37 +++++++++++++++++++++++++++++++++++-
 2 files changed, 38 insertions(+), 2 deletions(-)

Make <asm/setup.h> usable by the boot code.

Clean up vestiges of the old command-line protocol from setup.h and
head_32.S (it is still supported from the boot loader point of
view, since it is converted to the new command-line protocol by the
boot code.)
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

During hibernation and suspend on x86_64 save CPU registers in the saved_context
structure rather than in a handful of separate variables.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The x86_64 arch/x86/kernel/Makefile uses references into 
arch/x86/kernel/cpu/... to use code from there.

Unifiy it with the nicely structured i386 way and reuse the existing
subdirectory make rules.

Also move the machine check related source into ...kernel/cpu/mcheck,
where the other machine check related code is.

No code change.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Move mce.c to mce_32.c to allow the later move of the x86_64 mce.c
from arch/x86/kernel/ to ...kernel/cpu/mcheck

No code change.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Prepare the makefiles in x86/kernel/cpu and x86/kernel/cpu/mcheck to
be used by the x86_64 build as well.

No code change.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Preperatory patch to simplify the sharing of Makefiles in
arch/x86.

Linus came up with this during a discussion about the ugliness of
ifeq($CONFIG_X86_32),y) and obj-$(CONFIG_X86_32) in the shared
Makefiles.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Most of contents in crash are same.
Signed-off-by: NHiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Preperatory patch to allow crash_32/64.c merging
Signed-off-by: NHiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Signed-off-by: NAlejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The previous patch wasn't correctly handling the 'count' variable.  If
a CPU gave bad results on the 1st or 2nd run but good results on the
3rd, it wouldn't do the correct thing.  No idea if any such CPU
exists, but the patch below handles that case by discarding the bad
runs.

If a bad result (too quick, or too slow) occurs on any of the 3 runs
it will be discarded.

Also updated some comments to explain what's going on.
Signed-off-by: NDave Johnson <djohnson@sw.starentnetworks.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

I ran into this problem on a system that was unable to obtain NTP sync
because the clock was running very slow (over 10000ppm slow). ntpd had
declared all of its peers 'reject' with 'peer_dist' reason.

On investigation, the tsc_khz variable was significantly incorrect
causing xtime to run slow.  After a reboot tsc_khz was correct so I
did a reboot test to see how often the problem occurred:

Test was done on a 2000 Mhz Xeon system.  Of 689 reboots, 8 of them
had unacceptable tsc_khz values (>500ppm):

 range of tsc_khz  # of boots  % of boots
 ----------------  ----------  ----------
        < 1999750           0      0.000%
1999750 - 1999800          21      3.048%
1999800 - 1999850         166     24.128%
1999850 - 1999900         241     35.029%
1999900 - 1999950         211     30.669%
1999950 - 2000000          42      6.105%
2000000 - 2000000           0      0.000%
2000050 - 2000100           0      0.000%
                   [...]
2000100 - 2015000           1      0.145%  << BAD
2015000 - 2030000           6      0.872%  << BAD
2030000 - 2045000           1      0.145%  << BAD
2045000 <                   0      0.000%

The worst boot was 2032.577 Mhz, over 1.5% off!

It appears that on rare occasions, mach_countup() is taking longer to
complete than necessary.

I suspect that this is caused by the CPU taking a periodic SMI
interrupt right at the end of the 30ms calibration loop.  This would
cause the loop to delay while the SMI BIOS hander runs. The resulting
TSC value is beyond what it actually should be resulting in a higher
tsc_khz.

The below patch makes native_calculate_cpu_khz() take the best
(shortest duration, lowest khz) run of it's 3 calibration loops.  If a
SMI goes off causing a bad result (long duration, higher khz) it will
be discarded.

With the patch applied, 300 boots of the same system produce good
results:

 range of tsc_khz  # of boots  % of boots
 ----------------  ----------  ----------
        < 1999750           0      0.000%
1999750 - 1999800          30     10.000%
1999800 - 1999850         166     55.333%
1999850 - 1999900          89     29.667%
1999900 - 1999950          15      5.000%
1999950 <                   0      0.000%

Problem was found and tested against 2.6.18.  Patch is against 2.6.22.
Signed-off-by: NDave Johnson <djohnson@sw.starentnetworks.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

It seems commit 09cadedb was incomplete 
due to a clash with the x86 architecture merge.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Reduce the function pointer mess of the m68knommu timer code by calling
directly to the local hardware's timer setup, and expose the local
common timer interrupt handler to the lower level hardware timer.

Ultimately this will save definitions of all these functions across all
the platform code to setup the function pointers (which for any given
m68knommu CPU family member can be only one set of hardware timer
functions).
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove build reference to arch/m68knommu/boot directory, it doesn't
exist.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove use of undefined symbols CONFIG_TELOS, CONFIG_M68EZ328ADS
and CONFIG_ALMA_ANS.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix system call restart handling. We can call directly to the
restart handler, no need to back track through trap that isn't
even implemented on m68knommu.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add make support for the Savant/Rosie1 board.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There is no separate stack region addresses to print at startup time,
so remove it from the debug listing
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add configure support for the Savant/Rosie1 board.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Updated defconfig with new options for m68knommu.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the system call code for handling syscall tracing, so strace
and gdbserver work properly.

This fix originally developed by Philippe De Muyter and Stuart Hughes.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

zero out dma_length in the entry immediately following the last mapped
entry for unmap_sg.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Signed-off-by: NAlejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>