This is a baby-step in the direction of having finer-grained
locking than the struct_mutex. Specifically, this will enable
new debugging code to read the active list for printing out
GPU state when the GPU is wedged, (while the struct_mutex is
held, of course).
Signed-off-by: NCarl Worth <cworth@cworth.org>
[anholt: indentation fix]
Signed-off-by: NEric Anholt <eric@anholt.net>

This brings SDVO TV support from 2D driver, including origin
fix f1ca56e17d0 and later fix 2fcf4fcccfe. Also fix wrong modeline
definitions for SDVO TV.
Signed-off-by: NZhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

This brings fix commit acde0ef683 from 2D driver.
Signed-off-by: NZhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

This brings fix commit 62c0c2f5549a from 2D driver.
Signed-off-by: NZhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Fix compile error of intel_sdvo_debug_response(),
and explicit use KERN_DEBUG for printk.
Signed-off-by: NZhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Only set TV DAC in property change seems doesn't work, we have to
setup whole crtc pipe which assigned to TV alone.
Signed-off-by: NZhenyu Wang <zhenyu.z.wang@intel.com>
[anholt: Note that this should also fix the oops at startup with new 2D]
Signed-off-by: NEric Anholt <eric@anholt.net>

If there's no real property change, don't need to set TV mode again.
Signed-off-by: NZhenyu Wang <zhenyu.z.wang@intel.com>
[anholt: checkpatch.pl fix]
Signed-off-by: NEric Anholt <eric@anholt.net>

udelay() of 20 milliseconds really ought to just use mdelay(), that avoids
the various wrap scenarios and also is more readable
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Add VGA port hotplug detection to the i915 driver.  When KMS is enabled,
plugging in or removing a VGA cable from the VGA connector will
generate a uevent, which indicates to userspace that it should re-probe
outputs on this device (to determine modes, etc.).
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[anholt: dropped extra PORT_HOTPLUG_STAT clear with ack from jbarnes]
Signed-off-by: NEric Anholt <eric@anholt.net>

IGD device only has last 1 page used by GTT.  This should match the AGP gart
code.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

drm_get_edid will store edid into raw_edid, so when freeing edid memory,
at the same time clean raw_edid pointer.
Signed-off-by: NMa Ling <ling.ma@intel.com>
[anholt: Note that raw_edid is not currently used anywhere]
Signed-off-by: NEric Anholt <eric@anholt.net>

Indicates something is wrong with the mapping; and apparently triggers
in current kernels.
Signed-off-by: NJesse Barnes <jbarnes@virtuosugeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

This fixes all the tiling problems with the 2d ddx. glxgears still doesn't work.
Changes:

- fix a copy&paste error in i8xx fence reg setup. It resulted in an at most a
  512KB offset of the fence reg window, so was only visible sometimes.
- add tests for stride and object size constrains (also for i915 and 1965 class
  hw). Userspace seems to have an of-by-one bug there, which changes the fence
  size by at most 512KB due to an overflow.
- because i8xx hw is quite old (and therefore not as well-tested) I left 2 debug
  WARN_ONs in the i8xx fence reg setup code to hopefully catch any further
  overflows in the bit-fields. Lastly there's one small change to make the
  alignment checks more consistent.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=20289Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NEric Anholt <eric@anholt.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (59 commits)
  ide-floppy: do not complete rq's prematurely
  ide: be able to build pmac driver without IDE built-in
  ide-pmac: IDE cable detection on Apple PowerBook
  ide: inline SELECT_DRIVE()
  ide: turn selectproc() method into dev_select() method (take 5)
  MAINTAINERS: move old ide-{floppy,tape} entries to CREDITS (take 2)
  ide: move data register access out of tf_{read|load}() methods (take 2)
  ide: call {in|out}put_data() methods from tf_{read|load}() methods (take 2)
  ide-io-std: shorten ide_{in|out}put_data()
  ide: rename IDE_TFLAG_IN_[HOB_]FEATURE
  ide: turn set_irq() method into write_devctl() method
  ide: use ATA_HOB
  ide-disk: use ATA_ERR
  ide: add support for CFA specified transfer modes (take 3)
  ide-iops: only clear DMA words on setting DMA mode
  ide: identify data word 53 bit 1 doesn't cover words 62 and 63 (take 3)
  au1xxx-ide: auide_{in|out}sw() should be static
  ide-floppy: use ide_pio_bytes()
  ide-{floppy,tape}: fix padding for PIO transfers
  ide: remove CONFIG_BLK_DEV_IDEDOUBLER config option
  ...

* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (88 commits)
  PCI: fix HT MSI mapping fix
  PCI: don't enable too much HT MSI mapping
  x86/PCI: make pci=lastbus=255 work when acpi is on
  PCI: save and restore PCIe 2.0 registers
  PCI: update fakephp for bus_id removal
  PCI: fix kernel oops on bridge removal
  PCI: fix conflict between SR-IOV and config space sizing
  powerpc/PCI: include pci.h in powerpc MSI implementation
  PCI Hotplug: schedule fakephp for feature removal
  PCI Hotplug: rename legacy_fakephp to fakephp
  PCI Hotplug: restore fakephp interface with complete reimplementation
  PCI: Introduce /sys/bus/pci/devices/.../rescan
  PCI: Introduce /sys/bus/pci/devices/.../remove
  PCI: Introduce /sys/bus/pci/rescan
  PCI: Introduce pci_rescan_bus()
  PCI: do not enable bridges more than once
  PCI: do not initialize bridges more than once
  PCI: always scan child buses
  PCI: pci_scan_slot() returns newly found devices
  PCI: don't scan existing devices
  ...

Fix trivial append-only conflict in Documentation/feature-removal-schedule.txt

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] cio: online_store - trigger recognition for boxed devices
  [S390] cio: disallow online setting of device in transient state
  [S390] cio: introduce notifier for boxed state
  [S390] cio: introduce ccw_device_schedule_sch_unregister
  [S390] cio: wake up on failed recognition
  [S390] fix hypfs build failure
  [PATCH] sysrq: include interrupt.h instead of irq.h

The current logic for dmi matching in efifb does not allow efifb to load
on all hardware that we can dmi match for.

For a real world example, boot with elilo (3.7 or 3.8 vanilla) and on a
Apple (MacBook) and EFI framebuffer driver will not load (you will have no
video).  This specific hardware is efi v1.10, so we have UGA and not GOP.
Without special bootloader magic (i.e.  extra elilo patches for UGA
graphics detection) no screen info will be passed to the kernel and as a
result efifb will not load.

This patch allows the dmi match to happen by moving it to earlier in
efifb_init, and sets the video type (in set_system) so that efifb can load
when we have a valid dmi match and already know the specifics of the
hardware.

Without this patch the efifb driver will fail to load in the event screen
info is not found and passed in by the bootloader, being that we will
never get to look for a dmi match.  A primary reason for matching with dmi
is because not all bootloaders detect the video info properly.  The
solution is that in the event of a dmi match, we should set
screen_info.orig_video_isVGA.  Most bootloaders fail to set screen info on
Apple hardware, and this is a big problem for people who use Apple
hardware.

Tested on a MacBook SantaRosa with elilo-3.8 (vanilla) and resolves the
issue, the dmi match now works, EFI framebuffer now loads and video works.
Signed-off-by: NBrian Maly <bmaly@redhat.com>
Acked-by: NHuang Ying <ying.huang@intel.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Chandramouli Narayanan <mouli@linux.intel.com>
Acked-by: NPeter Jones <pjones@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove Kconfig option for tridentfb acceleration.  The acceleration can be
switched off with modules "noaccel" parameter.

The acceleration for Trident chips was fixed in the 2.6.27 kernel.

Also, add CyberXXX and CyberBlade names to Kconfig option's name.  It should
make easier to find the tridentfb choice for cyblafb driver's users.  The
cyblafb driver has been replaced by the tridentfb driver.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Save one fifo entry on cursor enabling and disabling.

Save another fifo entry for FB_CUR_SETPOS operation by removing redundant one.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A hardware cursor is left enabled in the fb_set_par() which is called when a
new console is created.  This is inconsistent with software cursor's
behaviour.

Also, this makes a hardware cursor always visible in the Xfbdev (Xorg kdrive)
server.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: Risto Suominen <risto.suominen@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove mutex from the nvidiafb_open/nvidiafb_release functions as these
operations are mutexed at fb layer.
Signed-off-by: NAlessio Igor Bogani <abogani@texware.it>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add suspend/resume for the Acer Travelmate 290D/292LMi with the following
graphic-chip:

01:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV350
[Mobility Radeon 9600 M10] [1002:4e50] (prog-if 00 [VGA controller])
	Subsystem: Acer Incorporated [ALI] TravelMate 290 [1025:005a]
	Flags: bus master, 66MHz, medium devsel, latency 128, IRQ 10
	Memory at a8000000 (32-bit, prefetchable) [size=128M]
	I/O ports at c100 [size=256]
	Memory at e0010000 (32-bit, non-prefetchable) [size=64K]
	[virtual] Expansion ROM at a0000000 [disabled] [size=128K]
	Capabilities: [58] AGP version 2.0
	Capabilities: [50] Power Management version 2
	Kernel driver in use: radeonfb
	Kernel modules: radeonfb
Signed-off-by: NWolfgang Kroener <lkml@azog.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The blank operation should receive FB_BLANK_POWERDOWN, not VESA_POWERDOWN.
Signed-off-by: NFelipe Contreras <felipe.contreras@nokia.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Andrea Righi <righi.andrea@gmail.com>
Acked-by: NTrilok Soni <soni.trilok@gmail.com>
Cc: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If the vbemode option is used, uvesafb calls fb_get_mode() without first
setting the resolution in info->var.  This results in a division by zero
in fb_get_mode(), as evidenced e.g.  in [1].  Fix this by ensuring the
info->var structure is populated before fb_get_mode() is called.

[1] http://bugzilla.kernel.org/show_bug.cgi?id=11661#c37Signed-off-by: NMichal Januszewski <spock@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A tridentfb driver has all the functionality of the cyblafb driver without
the bugs of the latter.

Changes to the tridentfb driver:

- FBINFO_READS_FAST added to the tridentfb.  The cyblafb used a blitter
  for scrolling which is faster than color expansion on Cyberblade
  chipsets.  The blitter is slower on a discrete Blade3D core.  Use the
  blitter for scrolling in the tridentfb only for integrated Blade3D
  cores.  Now, scrolling speed is about equal for the tridentfb and the
  cyblafb.

- a copyright notice addition is done on request of Jani Monoses (the
  first author of the tridentfb).

Tested on AGP Blade3D card and PCChips
M787CLR motherboard: VIA C3 cpu +
VT8601 north  bridge (aka Cyberblade/i1).
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Jani Monoses" <jani@ubuntu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the newer Samsung devices, such as found in the S3C2443,
S3C6400 or S3C6410 series SoC.

It currently does not support all the alpha- or chroma-key options but it
will support more exporting more than one framebuffer ready for adding
overlay and blending functions.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There is no entry for n411.c to be built, include one in Makefile.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Otherwise this will already return 0 if iteration MAXLOOP-2 occurs in the
first loop.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Cc: Joseph Chan <josephchan@via.com.tw>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NMichal Januszewski <michalj@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NMichal Januszewski <michalj@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NOndrej Zajicek <santiago@crfreenet.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- fix cmap leak in removal path
 - fix cmap leak when register_framebuffer fails
 - check return value of fb_alloc_cmap
 - don't continue with driver setup if register_framebuffer fails

[krzysztof.h1@wp.pl: spotted missing iounmap]
[randy.dunlap@oracle.com: move data declaration before any code]
Signed-off-by: NAndres Salomon <dilinger@debian.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With for(div = 0; div < max_clk_div; div++) { ... } div reaches max_clk_div.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Cc: Joe Perches <joe@perches.com>
Acked-by: NTrilok Soni <soni.trilok@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The s1d13xxx chip provides two values of identification value: the
Production id (e.g 13506/13505/13806..) and a revision number 0,1,2,3).
Together these can help us to differentiate between similiar setups.

This patch adds the proper way of grabbing both those values and save them
for future reference (in order to decide what functions a card supports,
e.g acceleration).

We also move away from the concept of all s1d13xxx = s1d13806 when we
really support alot more.

[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: simplify s1d13xxxfb_probe()]
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With a postfix decrement t reaches -1 on timeout which results in a
return of 0.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAndres Salomon <dilinger@debian.org>
Acked-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- fix cmap leak in removal path

- fix cmap leak when register_framebuffer fails
Signed-off-by: NAndres Salomon <dilinger@debian.org>
Acked-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- fix cmap leak in removal path

- fix cmap leak when register_framebuffer fails

- check return value of fb_alloc_cmap
Signed-off-by: NAndres Salomon <dilinger@debian.org>
Acked-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix cmap leak when register_framebuffer fails.
Signed-off-by: NAndres Salomon <dilinger@debian.org>
Acked-by: NKrzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- fix cmap leak in removal path
 - fix cmap leak when register_framebuffer fails
Signed-off-by: NAndres Salomon <dilinger@debian.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>