This patch exposes PRM layout for handling MPEGC (Management PCIe
General Configuration).

This will be used in the downstream patch for configuring MPEGC via the
driver.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

This change adds the infrastructure to mlx5 core fw tracer.
It introduces the following 4 new registers:
MLX5_REG_MTRC_CAP  - Used to read tracer capabilities
MLX5_REG_MTRC_CONF - Used to set tracer configurations
MLX5_REG_MTRC_STDB - Used to query tracer strings database
MLX5_REG_MTRC_CTRL - Used to control the tracer

The capability of the tracing can be checked using mcam access
register, therefore, the mcam access register interface will expose
the tracer register.
Signed-off-by: NFeras Daoud <ferasda@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

MLX5 IB HCA offers the memory key, dump_fill_mkey to boost
performance by forcing local HCA operations to skip the PCI bus
access,

This patch adds needed hardware definitions.
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>

Add capability bit in PCAM register and RoCE ICRC error counter
to PPCNT register.
Signed-off-by: NTalat Batheesh <talatb@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>

This patch updates the mlx5_ifc structures and
command interface to support DEVX.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>

The FPGA queue pair (QP) event fires whenever a QP on the FPGA
transitions to the error state.

At this stage, this event is unrecoverable, it may become recoverable
in the future.
Signed-off-by: NIlan Tayari <ilant@mellanox.com>
Signed-off-by: NAdi Nissim <adin@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Temperature warning event is sent by FW to indicate high temperature
as detected by one of the sensors on the board.
Add handling of this event by writing the numbers of the alert sensors
to the kernel log.
Signed-off-by: NIlan Tayari <ilant@mellanox.com>
Signed-off-by: NAdi Nissim <adin@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new mini-CQE format includes byte-count, checksum
and stride index.
Reviewed-by: NYishai Hadas <yishaih@mellanox.com>
Reviewed-by: NGuy Levi <guyle@mellanox.com>
Signed-off-by: NYonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

If set, the FDB table supports the forward action with a
destination list that includes a flow table.
Signed-off-by: NChris Mi <chrism@mellanox.com>
Reviewed-by: NPaul Blakey <paulb@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add firmware command interface to read and write PPTB and PBMC
registers.

PPTB register enables mappings priority to a specific receive buffer.

PBMC registers enables changing the receive buffer's configuration such
as buffer size, xon/xoff thresholds, buffer's lossy property and
buffer's shared property.
Signed-off-by: NHuy Nguyen <huyn@mellanox.com>
Reviewed-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add pbmc and pptb in the port_access_reg_cap_mask. These two
bits determine if device supports receive buffer configuration.
Signed-off-by: NHuy Nguyen <huyn@mellanox.com>
Reviewed-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The source e-switch owner allows a vport on one e-switch port be associated
with a rule defined on the second port e-switch.

The role of the source eswitch owner valid bit in the flow group is to
allow the firmware fail driver attempts to wild card the source eswitch
match field. If this bit is not set, the firmware ignores the source
eswitch owner field totally.
Signed-off-by: NShahar Klein <shahark@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The destination e-switch owner allows a rule in namespace of one e-switch
owner to point to a vport that is natively associated with another
e-switch owner.
Signed-off-by: NShahar Klein <shahark@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
Under merged eswitch, both the matching on source vport and setting
destination vport can have a 2nd attribute which is the vhca id of the
eswitch owner.

For example:
esw0: {match: <src vport=1 owner=0> action: fwd to <dst vport=7, owner=1>}
is a flow set on eswitch0 matching on source vport=1 from his eswitch
and the action being fwd to dest vport=7 of eswitch1.
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NShahar Klein <shahark@mellanox.com>
Reviewed-by: NOr Gerlitz Klein <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

This patch reports the device's capbilities to offload
encapsulated MPLS tunnel protocols to user-space:
- Capability to offload MPLS over GRE.
- Capability to offload MPLS over UDP.
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NAriel Levkovich <lariel@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

This patch introduces support for the MPLS flow spec and
allows the creation of rules that are matching on the
MPLS label.

Applying the rule matching depends on the flow specs order and
the location of the MPLS in the spec list as there are different
configurations to be made in the device in the cases of MPLSoGRE
and MPLSoUDP vs. non-encapsulated MPLS.
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NAriel Levkovich <lariel@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Add routines for manipulating TLS TX offload contexts.

In Innova TLS, TLS contexts are added or deleted
via a command message over the SBU connection.
The HW then sends a response message over the same connection.

Add implementation for Innova TLS (FPGA-based) hardware.

These routines will be used by the TLS offload support in a later patch

mlx5/accel is a middle acceleration layer to allow mlx5e and other ULPs
to work directly with mlx5_core rather than Innova FPGA or other mlx5
acceleration providers.

In the future, when IPSec/TLS or any other acceleration gets integrated
into ConnectX chip, mlx5/accel layer will provide the integrated
acceleration, rather than the Innova one.
Signed-off-by: NIlya Lesokhin <ilyal@mellanox.com>
Signed-off-by: NBoris Pismenny <borisp@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change updates the mlx5 interface to create mkey
on the device.

The updates in the command mailbox include increasing the
access mode type field to 5 bits in order to support additional
types such as MLX5_MKC_ACCESS_MODE_MEMIC which represents device
memory access type and will be used when registering MR on allocated
device memory.

All the places that use the old access mode format are adjusted as
well.
Signed-off-by: NAriel Levkovich <lariel@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

This patch adds the mlx5_ib driver implementation for the device
memory allocation API.
It implements the ib_device callbacks for allocation and deallocation
operations as well as a new mmap command support which allows mapping
an allocated device memory to a VMA.

The change also adds reporting of device memory maximum size and
alignment parameters reported in device capabilities.

The allocation/deallocation operations are using new firmware
commands to allocate MEMIC memory on the device.
Signed-off-by: NAriel Levkovich <lariel@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

This patch adds querying of device memory capabilities by the mlx5_core
driver during initialization.

Device memory capabilities is a new capability type and structure
which contains the necessary data that is needed for future device
memory allocation.

The presence of this new capabilities struct is indicated in the
general capabilities struct which is queried first by the driver.
If the presence bit is set, the driver will also query the new
capabilities struct and save it in the device context.
Signed-off-by: NAriel Levkovich <lariel@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Current Striding RQ HW feature utilizes the RX buffers so that
there is no wasted room between the strides. This maximises
the memory utilization.
This prevents the use of build_skb() (which requires headroom
and tailroom), and demands to memcpy the packets headers into
the skb linear part.

In this patch, whenever a set of conditions holds, we apply
an RQ configuration that allows combining the use of linear SKB
on top of a Striding RQ.

To use build_skb() with Striding RQ, the following must hold:
1. packet does not cross a page boundary.
2. there is enough headroom and tailroom surrounding the packet.

We can satisfy 1 and 2 by configuring:
	stride size = MTU + headroom + tailoom.

This is possible only when:
a. (MTU - headroom - tailoom) does not exceed PAGE_SIZE.
b. HW LRO is turned off.

Using linear SKB has many advantages:
- Saves a memcpy of the headers.
- No page-boundary checks in datapath.
- No filler CQEs.
- Significantly smaller CQ.
- SKB data continuously resides in linear part, and not split to
  small amount (linear part) and large amount (fragment).
  This saves datapath cycles in driver and improves utilization
  of SKB fragments in GRO.
- The fragments of a resulting GRO SKB follow the IP forwarding
  assumption of equal-size fragments.

Some implementation details:
HW writes the packets to the beginning of a stride,
i.e. does not keep headroom. To overcome this we make sure we can
extend backwards and use the last bytes of stride i-1.
Extra care is needed for stride 0 as it has no preceding stride.
We make sure headroom bytes are available by shifting the buffer
pointer passed to HW by headroom bytes.

This configuration now becomes default, whenever capable.
Of course, this implies turning LRO off.

Performance testing:
ConnectX-5, single core, single RX ring, default MTU.

UDP packet rate, early drop in TC layer:

--------------------------------------------
| pkt size | before    | after     | ratio |
--------------------------------------------
| 1500byte | 4.65 Mpps | 5.96 Mpps | 1.28x |
|  500byte | 5.23 Mpps | 5.97 Mpps | 1.14x |
|   64byte | 5.94 Mpps | 5.96 Mpps | 1.00x |
--------------------------------------------

TCP streams: ~20% gain
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In some firmware configuration, UMR usage from Virtual Functions is restricted.
This information is published to the driver using new capability bits.

Avoid using UMRs in these cases and use the Firmware slow-path flow to create
mkeys and populate them with Virtual to Physical address translation.

Older drivers that do not have this patch, will end up using memory keys that
aren't populated with Virtual to Physical address translation that is done
part of the UMR work.
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Tested-by: NLaurence Oberman <loberman@redhat.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Newer NICs (ConnectX-5 and onward) can apply vlan pop or push as an
action taking place during flow steering. Add the core bits for that.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Added the following packets dropped while vport down statistics:

Rx dropped while vport down - counts packets which were steered by
e-switch to a vport, but dropped since the vport was down. This counter
will be shown on ip link tool as part of the vport rx_dropped counter.

Tx dropped while vport down - counts packets which were transmitted by
a vport, but dropped due to vport logical link down. This counter
will be shown on ip link tool as part of the vport tx_dropped counter.

The counters are read from FW by command QUERY_VNIC_ENV.
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Added the following packets drop counter:
Rx steering missed dropped packets - counts packets which were dropped
due to miss on NIC rx steering rules.
This counter will be shown on ethtool as a new counter called
rx_steer_missed_packets.
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add support for new FW command QUERY_VNIC_ENV.
The command is used by the driver to query vnic diagnostic statistics
from FW.
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Implement set/get functions to configure PFC stall prevention
timeout by tunables api through ethtool.
By default the stall prevention timeout is configured to 8 sec.
Timeout range is: 80-8000 msec.

Enabling stall prevention with the auto timeout will set
the timeout to 100 msec.
Signed-off-by: NInbar Karmy <inbark@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add the needed capability bit and counters to device spec description.
Expose the following two counters in ethtool:

tx_pause_storm_warning_events: when the device is stalled for a period
longer than a pre-configured watermark, the counter increase, allowing
the debug utility an insight into current device status.

tx_pause_storm_error_events: when the device is stalled for a period
longer than a pre-configured timeout, the pause transmission is disabled,
and the counter increase.
Signed-off-by: NInbar Karmy <inbark@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add two new parameters: max_burst_sz and typical_pkt_size (both
in bytes) to rate limit configurations.

max_burst_sz: The device will schedule bursts of packets for an
SQ connected to this rate, smaller than or equal to this value.
Value 0x0 indicates packet bursts will be limited to the device
defaults. This field should be used if bursts of packets must be
strictly kept under a certain value.

typical_pkt_size: When the rate limit is intended for a stream of
similar packets, stating the typical packet size can improve the
accuracy of the rate limiter. The expected packet size will be
the same for all SQs associated with the same rate limit index.

Ethernet driver is updated according to this change, but these two
parameters will be kept as 0 due to lacking of proper way to get the
configurations from user space which requires to change
ndo_set_tx_maxrate interface.
Signed-off-by: NBodong Wang <bodong@mellanox.com>
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Reviewed-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Add helper functions that check if a protocol is
part of a flow steering match criteria.
Signed-off-by: NBoris Pismenny <borisp@mellanox.com>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NAviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Currently, we don't support egress flow steering namespace in mlx5
flow steering core implementation. However, when we want to encrypt
a packet, we model it as a flow steering rule in the egress path.
To overcome this, we add an empty egress namespace to flow steering.
This namespace is initialized only when ipsec support exists.
In the future, this will grow to a full blown full steering
implementation, resembling the ingress path.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NAviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Allow to specify the size of the hairpin queues along with the
packet buffer data size from the core setup code.

If the driver doesn't provide this, the FW applies proper value that
matches the provided data size and a FW chosen RQ stride size.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The latest merge between net and net-next introduced a complier assert in
mlx5 driver.  In hca_cap_bits older fields are kept along with newer
fields that should have replaced them.

Fixes: c02b3741 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are systems platform information management interfaces (such as
HOST2BMC) for which we cannot disable local loopback multicast traffic.

Separate disable_local_lb_mc and disable_local_lb_uc capability bits so
driver will not disable multicast loopback traffic if not supported.
(It is expected that Firmware will not set disable_local_lb_mc if
HOST2BMC is running for example.)

Function mlx5_nic_vport_update_local_lb will do best effort to
disable/enable UC/MC loopback traffic and return success only in case it
succeeded to changed all allowed by Firmware.

Adapt mlx5_ib and mlx5e to support the new cap bits.

Fixes: 2c43c5a0 ("net/mlx5e: Enable local loopback in loopback selftest")
Fixes: c85023e1 ("IB/mlx5: Add raw ethernet local loopback support")
Fixes: bded747b ("net/mlx5: Add raw ethernet local loopback firmware command")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add hairpin definitions to the IFC file.

This includes the HCA ID, few HCA hairpin capabilities, new
fields in RQ/SQ used later for the pairing and the WQ hairpin
data size attribute.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

When mlx5_ib_add is called determine if the mlx5 core device being
added is capable of dual port RoCE operation. If it is, determine
whether it is a master device or a slave device using the
num_vhca_ports and affiliate_nic_vport_criteria capabilities.

If the device is a slave, attempt to find a master device to affiliate it
with. Devices that can be affiliated will share a system image guid. If
none are found place it on a list of unaffiliated ports. If a master is
found bind the port to it by configuring the port affiliation in the NIC
vport context.

Similarly when mlx5_ib_remove is called determine the port type. If it's
a slave port, unaffiliate it from the master device, otherwise just
remove it from the unaffiliated port list.

The IB device is registered as a multiport device, even if a 2nd port is
not available for affiliation. When the 2nd port is affiliated later the
GID cache must be refreshed in order to get the default GIDs for the 2nd
port in the cache. Export roce_rescan_device to provide a mechanism to
refresh the cache after a new port is bound.

In a multiport configuration all IB object (QP, MR, PD, etc) related
commands should flow through the master mlx5_core_dev, other commands
must be sent to the slave port mlx5_core_mdev, an interface is provide
to get the correct mdev for non IB object commands.
Signed-off-by: NDaniel Jurgens <danielj@mellanox.com>
Reviewed-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Generate a unique 128bit identifier for each host and pass that value to
firmware in the INIT_HCA command if it reports the sw_owner_id
capability. Each device bound to the mlx5_core driver will have the same
software owner ID.

In subsequent patches mlx5_core devices will be bound via a new VPort
command so that they can operate together under a single InfiniBand
device. Only devices that have the same software owner ID can be bound,
to prevent traffic intended for one host arriving at another.

The INIT_HCA command length was expanded by 128 bits. The command
length is provided as an input FW commands. Older FW does not have a
problem receiving this command in the new longer form.
Signed-off-by: NDaniel Jurgens <danielj@mellanox.com>
Reviewed-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

In mlx5_ifc, struct size was not complete, and thus driver was sending
garbage after the last defined field. Fixed it by adding reserved field
to complete the struct size.

In addition, rename all set_rate_limit to set_pp_rate_limit to be
compliant with the Firmware <-> Driver definition.

Fixes: 7486216b ("{net,IB}/mlx5: mlx5_ifc updates")
Fixes: 1466cc5b ("net/mlx5: Rate limit tables support")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The QPTS register allows changing the priority trust state between pcp and
dscp. Add support to get/set trust state from device. When the port is
in pcp/dscp trust state, packet is routed by hardware to matching priority
based on its pcp/dscp value respectively.

The QPDPM register allow channing the dscp to priority mapping. Add support
to get/set dscp to priority mapping from device.
Note that to change a dscp mapping, the "e" bit of this dscp structure
must be set in the QPDPM firmware command.
Signed-off-by: NHuy Nguyen <huyn@mellanox.com>
Reviewed-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The QCAM register provides capability bit for all the QoS registers
using ACCESS_REG command.
Signed-off-by: NHuy Nguyen <huyn@mellanox.com>
Reviewed-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>