Fix the led device naming for the sdhci driver.

The led class documentation defines the led name to have the
form "devicename:colour:function" while not applicable sections
should be left blank.

To comply with the documentation the led device name is changed
from "mmc*" to "mmc*::".
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

This reverts commit a4b76193.

It turned out that the controller had problem running at the
higher speed, so go back to trusting the hardware capability
bits.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

CONFIG_LEDS_CLASS is defined only if led-class is built-in, otherwise
when it is a module the option is called CONFIG_LEDS_CLASS_MODULE. Led
support should also be activated in this case.
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Some high speed capable controllers forget to set the high speed
capability bit. Make sure we enable the functionality anyway.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

alpha:

drivers/mmc/host/sdhci.h:242: error: field 'sg_miter' has incomplete type

Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Improve the PIO handling so that it can service highmem pages.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Add support for the scatter-gather DMA mode present on newer controllers.
As the mode requires 32-bit alignment, non-aligned chunks are handled by
using a bounce buffer.

Also add some new quirks to handle controllers that have bugs in the
ADMA engine.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Gracefully handle when the device is suddenly removed. Do a test read
and avoid any further access if that read returns -1.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Give the quirk for broken timeout handling a better chance of handling
more controllers by simply classifying the system as broken and setting
a fixed value.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

The SDHCI interface is not PCI specific, yet the Linux driver was
intimitely connected to the PCI bus. This patch properly separates
the PCI specific portion from the bus independent code.

This patch is based on work by Ben Dooks but he did not have time
to complete it.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Otherwise it can only take the values 0/-1 which doesn't seem to
have been intended.

drivers/mmc/host/sdhci.h:190:20: error: dubious one-bit signed bitfield
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Acked-by: NPierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Hook up the controller LED to the LED subsystem, allowing more flexible
control than simply indicating an ongoing request.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Remove the use of the sdhci specific device name and use the mmc controller
name instead.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Some devices have several controllers; need add the index info to
device slot name host->slot_desc[]
Signed-off-by: NFeng Tang <feng.tang@intel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Some controllers have been designed on the assumption that all transfers
will be 32-bit aligned, both in start address and in size. This is not a
guarantee the SDHCI specification provides and not one we can provide.

Revert back to PIO for individual requests in order to work around the
hardware bug.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

It is fully legal for a controller to start issuing data related
interrupts before it has signalled that the command has completed.
Make sure the driver actually can handle this.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Make sure all headers in the files reflect their true position
in the tree.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

The controller has a bit indicating that one of the higher bits (the
error bits) are set. A previous bug caused this bit to be masked, but
since that bug has been fixed we have to clear it explicictly.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Clean up the drivers/mmc directory by moving card and host drivers
into subdirectories.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

mmc layer may introduce additional (compared to block layer) limits on
request size. Culling of the sg list to match adjusted request size
simplifies the handling of such cases in the low level driver, allowing
it to skip block count checks while processing sg entries.

(fixes for wbsd and sdhci by Pierre Ossman)
Signed-off-by: NAlex Dubov <oakad@yahoo.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Since we actively avoid highmem, calling kmap_atomic() instead
of page_address() is effectively only obfuscation.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Most controllers have an upper limit on the block size. Allow the host
drivers to specify this and make sure we avoid hitting this limit.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

The SDHCI spec implies that is is incorrect to set a clock
frequency above 25 MHz without setting the high speed bit.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Clarify my (Pierre's) position on which GPL versions apply.  The patch only
touches the source files where I am the only major author.  The people who
have made the minor commits to the files have been contacted and have no
issues with this change.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

As some specific controllers will have bugs, we need a way to map special
behaviour to certain hardware.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Properly test for controller interface to see if it's DMA capable.  As many
controllers are misconfigured in this regard, also add debug parameters to
force DMA support either way.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Check the interface version of the controller and bail out if it's an unknown
version.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The controller has an upper limit on the block size. Make sure we do not
cross it.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The sdhci controllers will issue an interrupt when a configurable number of
bytes have been transfered using DMA. The purpose is to handle multiple,
scattered memory pages.

Unfortunately, it requires that all transfers are completely aligned to
memory pages, which we cannot guarantee. So we just disable the function.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The sdhci controllers operate with blocks, not bytes. The PIO routines must
therefore make sure that the minimum unit transfered is a complete block.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Use the give timeout clock and calculate a proper timeout instead of using the
maximum at all times.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The sdhci controllers can support up to three voltage levels.  Detect which
and report back to the MMC layer.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Driver for the Secure Digital Host Controller Interface specification.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>