Use DIV_ROUND_UP macro for better readability.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Max8925 ldo status should be determined by two factors:
1. power up/down sequence selection(LDOCTL[4:2]).
2. i2c enable bit(LDOCTL[0]).

Max8925 ldo support two types of power up/down sequence:
1. flexible sequence(LDOCTL[4:2] = 0~6).
2. i2c sequence(LDOCTL[4:2] = 7).

With flexible sequence selected, the ldo is enabled during power up by default.
With i2c sequence selected, the ldo is controlled by the i2c enable bit(LDOCTL[0]).
Signed-off-by: NKevin Liu <kliu5@marvell.com>
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

With device tree support for regulators, its needed that the
regulator_dev->dev device has the right of_node attached.
To be able to do this add an additional parameter to the
regulator_register() api, wherein the dt-adapted driver can
then pass this additional info onto the regulator core.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Another group of drivers that are taking advantage of the implicit
presence of module.h -- and will break when we pull the carpet out
from under them during a cleanup.  Fix 'em now.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Force to enable i2c as power up/down sequence. Otherwise, SD/LDO can't
be enabled or disabled via accessing i2c bus.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Change the interface used by set_voltage() to report the selected value
to the regulator core in terms of a selector used by list_voltage().
This allows the regulator core to know the voltage that was chosen
without having to do an explict get_voltage(), which would be much more
expensive as it will generally access hardware.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Fix regulator enabling issue that is caused by typo error in is_enabled().
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

It is a good tone to reset driver data after unbinding the device.
Also change find_regulator_info() fro inline to __devinit - let compiler
figure out if it wants it to be inlined or not.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

MAX8925 contains 3 Buck and 20 LDO regulator.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>