- add usb phy devices
- add usb controller devices
- add usb vbus regulators
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Tested-by: NSubodh Nijsure <snijsure@grid-net.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Rename mxs dts files with soc name being the prefix, so that the board
dts file can be located easily by soc name, and we also gain the
consistency of naming.
Suggested-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Some pins are used as GPIOs in user space.
Signed-off-by: NLauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

AUART3 is not available anymore. Pins are used as GPIOs.
Signed-off-by: NLauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NLauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NLauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add HannStar display and device tree configuration.
Signed-off-by: NLauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NLauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add dtb-y target into Makefile.boot, so that "make ARCH=arm dtbs" can
build out all the dtbs listed there.  It's very useful for build-testing
all the <board>.dts when imx28.dtsi changes.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The enc28j60 spi device does not get converted to dts file, because
there is no mxs spi driver on mainline so far.  The enc28j60 spi
in mach-stmp378x_devb.c does not work anyway.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

FEC support is missing because we need to find a proper way to rewrite
tx28_add_fec0 for device tree boot.

Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Tested-by: NLauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The presence and muxing of lcdif control pins can vary much on different
boards.  Move them into imx28-evk.dts to make lcdif_24bit_pins_a only
about data pins, so that it can be reused by other boards.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Only pins GPMI_CE0N and GPMI_READY0 are generally used by other boards.
Move GPMI_CE1N and GPMI_READY1 into imx28-evk.dts to make gpmi_pins_a
more general, and can be used by other boards.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add flexan devices for imx28-evk board.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

mx23-olinuxino is a low cost board designed by Olimex.

It has the following features:

- Freescale iMX233 ARM926J processor at 454MHz
-64 MB RAM
-SD-card connector
-TV PAL/NTSC video output
-2 USB High Speed Hosts
-Ethernet 100 Mbit
-Stereo Audio Input
-Stereo Headphones Audio Output

More information at:
http://www.olimex.com/dev/imx233-olinuxino-maxi.htmlSigned-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add DT node for gpmi nand.
Also add pinctrl for gpmi nand.

Enable the gpmi-nand in mx23-evk board.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add lcd support for imx23-evk and imx28-evk.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add pwm device and pwm-backlight for imx23-evk and imx28-evk.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Enable rtc for imx23 and imx28.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add heartbeat gpio-leds for imx28-evk board.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add missing properties for fec, phy-supply, phy-reset-gpios and
phy-reset-duration, which are required by fec driver for successfully
probe fec from device tree, if bootloader hasn't set those things up.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add vmmc-supply for mmc device, so that the power to mmc slot can be
turned on by mmc driver if bootloader hasn't done it.

Also remove "okay" status for mmc1/ssp1, as the device has pin conflict
with gpmi-nand.  Actually the device is already disabled since the
mxs-mmc driver adopts pinctrl support because there is no pinctrl setup
for the device in dts.  Make this explicit by removing "okay" status.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add auart device for imx23-evk board.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The 8-bit mode mmc has pin conflicts with display.  Let's use 4-bit
mode by default, so that display can be enabled together later.

Also add vmmc-supply for mmc device.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Before gpio_request can directly ask pinctrl system to configure the
requested pin into gpio mode, we use "hog" entry (pinctrl state of
pin controller itself) to configure gpios.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add comments for pinmux-ids so that we do not have to keep looking at
Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt to read
all these pinmux-ids.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Use auxdata to attach mxsfb_platform_data for imx23-evk and imx28-evk.
We take this as a temporary solution for removing those board files,
and it should be updated to use common bindings for struct fb_videomode
when it becomes available.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add a simple device tree probe support for mxsfb driver.  Before
a common binding for struct fb_videomode is available, the driver will
keep using struct mxsfb_platform_data.  That said, platform code will
use auxdata to attach mxsfb_platform_data for device tree boot.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Move mxsfb.h into include/linux, so that mxsfb driver does not have to
include <mach/*> header.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: rtc-linux@googlegroups.com
Acked-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

As the flexcan driver has DT binding for some time now. This patch makes
the flexcan driver available in the can drivers menu if a SOC with flexcan
is enabled.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Cc: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Cc: Brian Lily <brian@crystalfontz.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Cc: Brian Lily <brian@crystalfontz.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The non-DT boot reads the mac from OTP and pass it to fec driver via
platform data.  The patch provides an equivalent support for device
tree boot, with reading mac from OTP and store it in device tree,
and fec driver can get the mac from device tree at its probe time.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add auart0 and auart3 support.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Allow device tree probing.

Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: <linux-serial@vger.kernel.org>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSubodh Nijsure <snijsure@grid-net.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Replace "gpmi" with "gpmi-nand" to get the
GPMI interface probing with DT instead of
failing to get clock.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
CC: Dong Aisheng <b29396@freescale.com>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Linux ARM kernel <linux-arm-kernel@lists.infradead.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>