In some cases hw recovery was taking an absurdly
long time due to ath10k waiting for things that
would never really complete.

Instead of waiting for inevitable timeouts poke
all completions and wakequeues and check if it's
still worth waiting.

Reading/writing ar->state requires conf_mutex.
Since waiters might be holding it introduce a new
flag CRASH_FLUSH so it's possible to tell waiters
to abort whatever they were waiting for.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

A frequent request have been to be able to provide calibration data from a
file as some of the AP devices store the calibration data on an MTD partition.
This patchset adds support for that and also makes it easier to add Device Tree
support later on.

The calibration data is found by using the id string provided by dev_name()
using this format:

cal-<bus>-<id>.bin

With PCI the id string contains bus, slot and func values. For example for a
PCI device in bus 2 slot 0, ath10k will try to retrieve a calibration data from
a file:

/lib/firmware/ath10k/cal-pci-0000:02:00.0.bin

The calibration data sequence is:

1. Check with request_firmware() if there's a calibration file
   ("cal-<bus>-<id>.bin") on the filesystem for this device. If yes, use that. If
   not, goto 2

2. Check if otp.bin is able to successfully load the calibration data
   from OTP. If yes, use that. If not, goto 3.

4. Print an error message that no calibration data found and stop driver
   initialization for this device.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is preparation for being able to download calibration data from a file.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Commit 3a0861ff ("ath10k: remove ath10k_bus") removed enum ath10k_bus
because it was not used for anything at the time. But now it's needed for for
retrieving the right calibration data file so add it back. Only new addition is
ath10k_bus_str().
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This can allow more than 32 stations to be supported
without over-running the bitmap.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add testmode interface for starting and using UTF firmware which is used to run
factory tests. This is implemented by adding new state ATH10K_STATE_UTF and user
space can enable this state with ATH10K_TM_CMD_UTF_START command. To go back to
normal mode user space can send ATH10K_TM_CMD_UTF_STOP.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The fw_crash_data was allocated too late. Upon
early firmware crash, before registering to
mac80211, it was possible to crash the whole
system:

 ath10k_pci 0000:00:05.0: device has crashed during init
 BUG: unable to handle kernel NULL pointer dereference at           (null)
 IP: [<ffffffffa0058005>] ath10k_debug_get_new_fw_crash_data+0x15/0x30 [ath10k_core]
 PGD 0
 Oops: 0002 [#1] SMP
 Modules linked in: ath10k_pci(O) ath10k_core(O) ath [last unloaded: ath]
 CPU: 3 PID: 29 Comm: kworker/u8:1 Tainted: G           O   3.17.0-rc2-wl-ath+ #447
 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
 Workqueue: ath10k_wq ath10k_core_register_work [ath10k_core]
 task: ffff88001eb01ad0 ti: ffff88001eb60000 task.ti: ffff88001eb60000
 RIP: 0010:[<ffffffffa0058005>]  [<ffffffffa0058005>] ath10k_debug_get_new_fw_crash_data+0x15/0x30 [ath10k_core]
 RSP: 0018:ffff88001eb63ce8  EFLAGS: 00010246
 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
 RDX: 0000000000000000 RSI: ffffc90001a09030 RDI: 0000000000000001
 RBP: ffff88001eb63cf0 R08: 0000000000000000 R09: ffff8800000bb200
 R10: 00000000000001e2 R11: ffff88001eb638de R12: ffff88001d7459a0
 R13: ffff88001d746ab0 R14: 00000000fffe14d4 R15: ffff88001d747c60
 FS:  0000000000000000(0000) GS:ffff88001fd80000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
 CR2: 0000000000000000 CR3: 000000001df34000 CR4: 00000000000006e0
 Stack:
  ffff88001d7459a0 ffff88001eb63d58 ffffffffa0083bbe ffff880000000010
  ffff88001eb63d68 ffff88001eb63d18 0000000000000002 0000000000059010
  ffffffffa0086fef 00000000deadbeef ffff88001d747a28 ffff88001d7459a0
 Call Trace:
  [<ffffffffa0083bbe>] ath10k_pci_fw_crashed_dump+0x2e/0xd0 [ath10k_pci]
  [<ffffffffa0085410>] __ath10k_pci_hif_power_up+0x5f0/0x700 [ath10k_pci]
  [<ffffffffa0085550>] ath10k_pci_hif_power_up+0x30/0xe0 [ath10k_pci]
  [<ffffffffa005bc7b>] ath10k_core_register_work+0x2b/0x520 [ath10k_core]
  [<ffffffff810689cc>] process_one_work+0x18c/0x3f0
  [<ffffffff81069011>] worker_thread+0x121/0x4a0
  [<ffffffff81068ef0>] ? rescuer_thread+0x2c0/0x2c0
  [<ffffffff8106daf2>] kthread+0xd2/0xf0
  [<ffffffff8106da20>] ? kthread_create_on_node+0x170/0x170
  [<ffffffff81857cfc>] ret_from_fork+0x7c/0xb0
  [<ffffffff8106da20>] ? kthread_create_on_node+0x170/0x170
 Code: 8b 40 38 48 c7 80 00 01 00 00 00 00 00 00 5b 5d c3 0f 1f 44 00 00 0f 1f 44 00 00 55 48 89 e5 53 48 8b 9f 90 1d 00 00 48 8d 7b 01 <c6> 03 01 e8 e3 ec 2b e1 48 8d 7b 18 e8 6a 4f 05 e1 48 89 d8 5b
 RIP  [<ffffffffa0058005>] ath10k_debug_get_new_fw_crash_data+0x15/0x30 [ath10k_core]
  RSP <ffff88001eb63ce8>
 CR2: 0000000000000000
 ---[ end trace 5d0ed15b050bcc1f ]---
 Kernel panic - not syncing: Fatal exception in interrupt
 Kernel Offset: 0x0 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffff9fffffff)
 ---[ end Kernel panic - not syncing: Fatal exception in interrupt

To prevent that split debug functions and allocate
fw_crash_data earlier.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This makes it a lot easier to log and debug
messages if there's more than 1 ath10k device on a
system.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Transport buffers weren't flushed and processed
before queueing hw recovery request to mac80211.

This could in theory result in an unwanted htt/wmi
rx events being processed while mac80211 recovers
the device and possibly interfere or even crash
the system.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware probing is done only once when driver is
registered and firmware version is guaranteed to
remain the same until driver is unregistered.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Sometimes users forget to include important info like firmware version,
so better to print all the info.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If spectral is unregistered after mac80211, the relayfs file has already
been removed recursively by mac/cfg80211, and spectral tries to remove
the file once more, thus leading to double free problems. Better clean
up spectral before to avoid that problem.
Reported-by: NKalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: NSimon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is not necessary anymore. There are no more
uncontrolled htc tx entry points.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Use the common convention of embedding private
structures inside parent structures. This
reduces allocations and simplifies pci probing
code.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This aims at fixing some rare scan bugs related to
firmware reporting unexpected scan event
sequences.

One such bug was if spectral scan phyerr reporting
prevented firmware from properly propagating scan
events to host. This led to scan timeout. After
that next scan would trigger scan completed event
first (before scan started event) leading to
ar->scan.in_progress and timeout timer states to
be overwritten incorrectly and making the very
next scan to hang forever.
Reported-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Adds the spectral scan feature for ath10k. The spectral scan is triggered by
configuring a mode through a debugfs control file. Samples can be gathered via
another relay debugfs file.

Essentially, to try it out:

ip link set dev wlan0 up
echo background > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan0 > samples

This feature is still experimental. Based on the original RFC patch of
Sven Eckelmann.
Signed-off-by: NSimon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The 10.2 firmware is a successor of 10.1 firmware
(formerly identified as 10.x). Both share a lot
but have some slight ABI differences that need to
be taken care of.

The 10.2 firmware introduces some new features but
those can be added in subsequent patches. This
patch makes ath10k boot and work with 10.2 with
comparable functionality to 10.1.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If firmware probing worker failed it called
device_release_driver() which synchronously called
remove() pci callback. The callback in turn waited
for the worker that called it to finish resulting
in a deadlock.

Waiting for a completion instead of a worker, like
some other drivers do, doesn't seem like the best
idea either:

  Syscall                 Worker

                          probe_fw()
  rmmod
  dev_lock()
  pci->remove()
  wait_for_completion()
                          complete_all()
                          device_release_driver()
                          dev_lock()
                          [sleep]
  free(ar)
  dev_unlock()
                          [resume]

There's no guarantee that Worker upon resuming can
still access any data/code of the module.

Leaving device bound to a driver is not as harmful
as deadlocking so remove the call to
device_release_driver() while a proper solution is
figured out.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware 10.x supports up to 8 virtual AP interfaces, but in a DFS
channel it was possible to create only 7 interfaces as ath10k internal
creates a monitor interface for DFS. Previous vdev map initialization
was missing enough space for 8 + 1 vdevs due to wrong define used and
that's why there was no space for 8th interface. Use the correct define
TARGET_10X_NUM_VDEVS with 10.x firmware to make it possible to create
the 8th virtual interface.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Print Kconfig options enabled/disabled in the build.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This reduces risk of races and prepares for more
hw restart fixes.

It also makes sense to perform teardown after
mac80211 starts its restart routine as it
guarantees it has stopped itself by then
(including tx queues).
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If ath10k was built into the kernel it could stall
booting for 120 seconds by default (60 seconds for
each firmware API variant) waiting for firmware
files before userspace was ready or filesystems
mounted.

Fix this by making the core registering
asynchronous.

This also shoves off about 1 second from boot time
on most systems since the driver is now mostly
initialized in a worker and modprobe takes very
little time to complete.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This will avoid unnecessary forward declaration of
any kind in the future.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It was possible to call hif_stop() 2 times through
ath10k_htc_connect_init() timeout failpath which
could lead to double free_irq() kernel splat for
multiple MSI interrupt case.

Re-order init sequence to avoid this problem. The
HTC stop shouldn't stop HIF implicitly since it
doesn't implicitly start it. Since the re-ordering
required some functions to be split/removed/renamed
rename a few functions to make more sense while at
it.
Reported-By: NBen Greear <greearb@candelatech.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It doesn't make much sense to even try suspending
the device when recovering. Recovering means the
device is unresponsive and waiting for suspend
procedure means taking a 3 second timeout waiting
for tx credits.

This speeds up firmware recovery significantly.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This makes it easier to debug what kind of board is used.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If OTP or firmware fails to load properly, print out some
extra info in the kernel logs.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Let user know the name of the board file if it is not
found, and make it easier to determine the firmware
api being used.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When we execute otp.bin in the target check that the result it returns doesn't
contain an error. This is to make sure that we don't accidentally use invalid
calibration data.

While at it, remove the useless label in the function and add few debug messages.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It's just cleaner to have separate argument for the parameter and result. Also
fix returned error value if response length is invalid.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In case of warm reset target need to be suspended.
Suspend function is extented to handle both cases
with disabling interrupts and without disabling interrupts.
Warm target reset requires suspend with all interrupts
disabled.

This patch depends on
ath10k: fix device initialization routine
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Suspend/resume callbacks are not protected by configuration mutex
so adding such protection. Also in order to simplify implemetation
of suspend function wait queue is replaced by completion.
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Aids in understanding excactly what a firmware is
offering.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This makes ath10k a lot less spammy by default.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

We can show the same amount of information in one line. And then
it's easier to show this information only during first firmware boot
(see next patch).

For UART printouts there's already a message when they are enabled so
no need to have a print when they are disabled, that's the default
anyway.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

HIF was not stopped properly in
ath10k_core_start() upon failure. This could cause
memory leaks of CE completions entries and
possibly other issues as well.

Move the HIF start/stop out of
ath10k_htc_wait_target(). The ctl_resp completion
is already prepared in ath10k_htc_init.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If the 'ar' registration fails early, the debug
objects were not initialized, and trouble ensued when
the object was later destroyed and the un-initialized
objects were accessed.

Per Kalle's suggestion, move the debug_destroy to the
core_unregister method.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If firmware crashes during FW probing it would try
to perform FW recovery which uses mac80211
workqueue before registering to mac80211.

Using internal workqueue solves the problem.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

mac80211 interface interations functions have
peculiar locking issues. This patch introduces
internal (to ath10k) vif list that will be used
for vif iteration purposes.

kvalo: remove extra INIT_LIST_HEAD()
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

drivers/net/wireless/ath/ath10k/core.c:507:2-3: Unneeded semicolon

 Removes unneeded semicolon.

Generated by: coccinelle/misc/semicolon.cocci
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>