After commit d9b19199
(always enable FW_LOADER unless EMBEDDED=y) we can remove
the FW_LOADER select's and corresponding dependencies
on HOTPLUG.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The type and type2 fields were unused and so could be removed.
Instead add a vfl_type field that contains the type of the video
device.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

All ioctl callbacks are now stored in a new v4l2_ioctl_ops struct. Drivers fill in
a const struct v4l2_ioctl_ops and video_device just contains a const pointer to it.

This ensures a clean separation between the const ops struct and the non-const
video_device struct.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

In a previous patch I merged both memory maps into a single struct, believing
that they could be combined. We've since found problems with streaming
multiple channels on the 885. I'm restoring the multiple memory map structs
- in line with the windows driver.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This may be cx23885 chip specific and may not work on the cx23887.
Analog and mpeg encoder streaming are still to be tested.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Ensure the correct tuner gets reset on demand.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Ensure the tuners and demods are brought in and out of reset during
driver startup.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

It was previously disabled pending a bugfix, which has since been
resolved.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Don't display the register when it's not appropriate for the specific port.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Certain DVB cards that have demodulators on TS1/VIDB were not streaming packets.
This ensure the pin directions on PAD_CTRL are set correctly, solving the issue.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

PAD_CTRL controls TS1 and TS2 input and output states, if the register
became corrupt the driver was never able to recover.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

With the HVR1800, trying to use video0 and video1 simultaneously caused
buffer corruption in the PCIe bridge. This fix reallocates video1
buffer locations to avoid the issue.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The functions in a header should not belong to another module. The prio functions
belong to v4l2-common.c, so move them to v4l2-common.h.

The ioctl functions belong to v4l2-ioctl.c, so create a new v4l2-ioctl.h header
and move those functions to it.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The field 'dev' is not the video device, but the parent of the video device.
Rename accordingly.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

VIDEOBUF_DVB depends on VIDEOBUF_CORE, not on VIDEOBUF_DMA_SG
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The new revision of this board uses the same pci subsystem id as the first
revision, but uses a S5H1411 demodulator instead of the S5H1409.

In the case of the FusionHDTV7 Dual Express,
if s5h1409_attach fails, try s5h1411_attach.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Convert cx23885-417 to use video_ioctl2
Signed-off-by: NDouglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The cx18 can support transport streams with newer firmwares. Add a TS
capability to the generic cx2341x module.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Only one frontend is enabled right now. The second frontend can lock,
but transport doesn't work yet.  The device will be supported as a
single tuner device until the second frontend is working.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The naming for the callbacks that handle the VIDIOC_ENUM_FMT and
VIDIOC_S/G/TRY_FMT ioctls was very confusing. Renamed it to match
the v4l2_buf_type name.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The current code passes a context pointer in the xc5000_config struct.
This context pointer is used in the tuner_callback function, used to
reset the device after firmware download.

The xc5000_config struct is a static structure, whose .priv member was
being assigned before calling xc5000_attach().  If there are more than
one of the same device type installed on a single system, the last one
to assign xc5000_config.priv will "win", and all others will cease to
function properly.

This patch passes the context pointer in xc5000_attach() rather that
storing it within the static struct xc5000_config.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Since:
1) FW_LOADER is defined as:

config FW_LOADER
        tristate "Userspace firmware loading support"
        depends on HOTPLUG

2) several V4L/DVB driver just selects it;

3) select is not smart enough to auto-select HOTPLUG, if select FW_LOADER.

So, All drivers that select FW_LOADER should also depend on HOTPLUG.

An easier solution (for the end-user perspective) would be to "select HOTPLUG".
However, live is not simple. This would cause recursive dependency issues like
this one:

drivers/usb/Kconfig:62:error: found recursive dependency: USB -> USB_OHCI_HCD
-> I2C -> MEDIA_TUNER -> MEDIA_TUNER_XC2028 -> HOTPLUG -> PCCARD -> PCMCIA ->
USB_ARCH_HAS_HCD -> MOUSE_APPLETOUCH -> USB
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

VIDEO_TUNER is responsible for compilation of tuners.ko module. This were the
previous behaviour before the creation of MEDIA_TUNER.

Before this patch, tuner.ko were created even for drivers that don't need a
tuner (like webcam drivers).
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The cx23885 driver used to use dvb-pll for LG-TDVS-H064F support on the
FusionHDTV5 Express.  This has since been converted to use tuner-simple
instead, once digital tuning support was added to tuner-simple.

Since cx23885 no longer uses dvb-pll, remove the #include "dvb-pll.h",
and the DVB_PLL Kconfig selection.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Thanks to Ingo Molnar for finding this.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

namespace for all of them.

There were several issues in the past, caused by the hybrid tuner design, since
now, the same tuner can be used by drivers/media/dvb and drivers/media/video.

Kconfig items were rearranged, to split V4L/DVB core from their drivers.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

cx23885: Enable cx23417 support on the HVR1800
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

cx23885: Add generic cx23417 hardware encoder support.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

DVB-T mode is now supported using the DiBcom dib7000p demodulator
and the Xceive xc3028L silicon tuner. Analog mode is not supported.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Reviewed-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch fixes several issues on SCODE:

1) The extracting tool weren't generating the proper tags for SCODE. This
   has almost no effect, since those tags shouldn't be used;

2) DIBCOM52 were using a wrong IF. It should be 5200, instead of 5700;

3) seek_firmware were wanting an exact match for firmware type. This is
   wrong. As result, no SCODE firmware were loaded;

4) A few files were including the wrong file for seeking demod firmwares;

5) XC3028_FE_DEFAULT can be used, if user doesn't want to load a firmware.
   However, this weren't documentated. This feature require more testing.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

For boards that require the avcore (cx25840) to be active, ensure
it gets loaded.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This adds support for DVB-T mode only, analog is not supported.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This adds support for DVB-T mode only, analog mode is not supported.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The adapter_nr module options can be used to allocate static adapter
numbers on a driver level. It avoids problems with changing DVB apapter
numbers after warm/cold boot or device unplugging and repluging.

Each driver holds DVB_MAX_ADAPTER long array of the preferred order of
adapter numbers.

options dvb-usb-dib0700 adapter_nr=7,6,5,4,3,2,1,0 would result in a
reversed allocation of adapter numbers.

With adapter_nr=2,5 it tries first to get adapter number 2 and 5. If
both are already in use it will allocate the lowest free adapter number.
Signed-off-by: NJanne Grunau <janne-dvb@grunau.be>
Acked-by: NHermann Pitton <hermann.pitton@arcor.de>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>