The memory was not zeroed - fix that. Also update the
iwl_fw_error_dump_info structure.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Its content can move to the caller.
While at it, move iwl_mvm_fw_error_rxf_dump to caller.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of reading all the data in the context of the
interrupt thread, collect the data in the restart flow
before the actual restart takes place so that the device
still has all the information.
Remove iwl_mvm_fw_error_sram_dump and move its content to
iwl_mvm_fw_error_dump.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The chunks of data do not need to be multipliers of 4 nor
4-bytes aligned.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Firmware folks seem say that this flag can make trouble.
Drop it. The advantage of CTS to self is that it slightly
reduces the cost of the protection, but make the protection
less reliable.

Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We should always prefer to use full RTS protection. Using
CTS to self gives a meaningless improvement, but this flow
is much harder for the firmware which is likely to have
issues with it.

CC: <stable@vger.kernel.org>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Split sched scan IEs to band specific and not band specific
blocks. Common IEs blocks may be sent to the FW once per command,
instead of per band.

This allows optimization of size of the command, which may be
required by some drivers (eg. iwlmvm with newer firmware version).

As this changes the mac80211 API, update all drivers to use the
new version correctly, even if they don't (yet) make use of the
split data.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some drivers (such as iwlmvm) can handle multiple bands in a single
HW scan request. Add a HW flag to indicate that the driver support
this. To hold the required data, create a separate structure for
HW scan request that holds cfg scan request and data about
different parts of the scan IEs.

As this changes the mac80211 API, update all drivers using it to
use the correct new function type/argument.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Current code did not allow sending the broadcast filtering command
for P2P Client interfaces. However, this was not enough, since once
broadcast filtering command was issued over the station interface
after the P2P Client connected, the command also attached the filters
to the P2P Client MAC which is not allowed (FW ASSERT 1063).

Fix this skipping P2P Client interfaces when constructing the broadcast
filtering command
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NArikX Nemtsov <arik@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This reverts commit dc9a1929.

3610 cards don't support UAPSD.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If the device fails during a restart, mac80211 now handles the
situation better but we still have a little bit of cleanup to
do in the driver - add the required code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NArikX Nemtsov <arik@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Since the new API allows multiple priorities, we need to
properly set the beacon's prorities in the TX cmd associated
to it.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Use extended beacon notification when supported by FW.
Set last beacon system time to AP or GO interface.
System time of last beacon can be used to avoid TBTT overlapping
between two interfaces, CSA and other uses.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Introduce new station flag STA_FLG_DISABLE_TX, which is modified with ADD_STA
command. This flag, when set, disables tx to the STA.
Provide an API (iwl_mvm_sta_modify_disable_tx) to modify this flag, which
should be used in channel switch and immediate quiet flows.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The beacon filtering configuration in d0i3 currently uses
the max value defined as 1024. However, with beacon interval
of 100ms we end up with too-frequent wakeups.

Instead, configure the escape timer to 0, asking the fw
to disable it altogether.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If BT is active, we need to refrain from using the shared
antenna. This logic is done in the firmware when we use the
link quality tables. But for management frames, the rate is
written in the Tx command by the driver.
Hence the driver needs to make sure not use the shared
antenna when BT is active for any frames that don't use
the rate scale table such as management frames or multicast.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This really belongs to the constants file.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the firmware enables TxTxCorunning, we can lift the
constaints on the rate control.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We can Tx in MIMO rates when we are in TxTx Disallow mode
just like we can when we are in Tight mode.
Same if we are in 5Ghz regardless of the mode we are.
Change the code to allow MIMO in these cases.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This can be used for testing.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Just in case sizes change in the OTP without proper SW
updating, an additional check is inserted when reading OTP
sections to assure no overflows occur.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Some of the maximum values of the parsed external NVM file
in the B-step of the 8000 HW family were updated, so this
updates these values.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The format of the CSR_HW_REV register has changed in 8000
HW family. To keep backwards compatibility, we store the
value of this register as usual in trans->hw_rev, only we
store it in the old format in this variable.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Don't use nvm_hw pointer if it is NULL. Print an error
message if the MAC address isn't valid.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

iwldvm stalls are often blamed on power management.  Add an option
to force it all the way off.
Signed-off-by: NAndy Lutomirski <luto@amacapital.net>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This adds need_update and write_actual to rx_queue and need_update
and an HCMD indicator to tx_queue.

On my card, rx_queue now looks like:

read: 181
write: 180
write_actual: 176
need_update: 0
free_count: 40
closed_rb_num: 181

tx_queue now looks like:

hwq 00: read=29 write=30 use=1 stop=0 need_update=0
hwq 01: read=0 write=0 use=1 stop=0 need_update=0
hwq 02: read=128 write=128 use=1 stop=0 need_update=0
hwq 03: read=0 write=0 use=1 stop=0 need_update=0
hwq 04: read=94 write=94 use=1 stop=0 need_update=0 HCMD
hwq 05: read=0 write=0 use=0 stop=0 need_update=0
hwq 06: read=0 write=0 use=0 stop=0 need_update=0
hwq 07: read=0 write=0 use=0 stop=0 need_update=0
hwq 08: read=0 write=0 use=0 stop=0 need_update=0
hwq 09: read=0 write=0 use=0 stop=0 need_update=0
hwq 10: read=0 write=0 use=0 stop=0 need_update=0
hwq 11: read=0 write=0 use=0 stop=0 need_update=0
hwq 12: read=0 write=0 use=0 stop=0 need_update=0
hwq 13: read=0 write=0 use=0 stop=0 need_update=0
hwq 14: read=0 write=0 use=0 stop=0 need_update=0
hwq 15: read=0 write=0 use=0 stop=0 need_update=0
hwq 16: read=0 write=0 use=0 stop=0 need_update=0
hwq 17: read=0 write=0 use=0 stop=0 need_update=0
hwq 18: read=0 write=0 use=0 stop=0 need_update=0
hwq 19: read=0 write=0 use=0 stop=0 need_update=0

This may help with debugging queue stalls.
Signed-off-by: NAndy Lutomirski <luto@amacapital.net>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

I've never seen this happen, but it's useful to rule it out.
Signed-off-by: NAndy Lutomirski <luto@amacapital.net>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Fix NVM channel attributes. Add indoor-only and GO Concurrent
bits. Remove DFS channel bit which is overlapped with radar.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The nvm_file should be loaded by default for SDIO
procucts only. Change the configuration accordingly.
While at it, fix a typo in the device name.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to use the firmware monitor. This capability
uses a lot of contiguous memory (up to 64MB), so make its
usage module parameter dependent.

The driver will try to allocate as much contiguous memory
as possible downgrading its requirements until the
allocation succeeds.

Dump this data into the fw-error dump file when an error
happens.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This is not related to mvm. Rename to iwl_fw_error_next_data.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This can be useful later for parsing since the parsing may
differ based on the device's family / bus.
Also add the human readable version of the firmware.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

MCS32 is currently not supported, so don't
declare support for it.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Use num of scan channels as advertised by fw TLV.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add one more 7265 series HW ID.
Edit one existing 7265 series HW ID.

CC: <stable@vger.kernel.org> [3.13+]
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The low-priority scan feature can be useful, e.g. for OBSS
scans (if those are required by the AP); add back support
for it, restoring the maximum out time to the value it was
for low-priority scan before that was removed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Use ksize to get scan command size instead of calculating it, to
avoid nasty bugs.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The current sched scan channel configuration code
configures all the supported channels for scanning.

However, this can result in SYSASSERT in some cases,
when the configured channel is disabled.

Instead, configure only the channels given in the
req struct, and set the channel_count field appropriately.

While on it, change the code to use channel->hw_value
instead of recalculating the channel number.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>