Eliminate lock_cpu_hotplug from kernel/sched.c and use sched_hotcpu_mutex
instead to postpone a hotplug event.

In the migration_call hotcpu callback function, take sched_hotcpu_mutex
while handling the event CPU_LOCK_ACQUIRE and release it while handling
CPU_LOCK_RELEASE event.

[akpm@linux-foundation.org: fix deadlock]
Signed-off-by: NGautham R Shenoy <ego@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is an attempt to provide an alternate mechanism for postponing
a hotplug event instead of using a global mechanism like lock_cpu_hotplug.

The proposal is to add two new events namely CPU_LOCK_ACQUIRE and
CPU_LOCK_RELEASE. The notification for these two events would be sent
out before and after a cpu_hotplug event respectively.

During the CPU_LOCK_ACQUIRE event, a cpu-hotplug-aware subsystem is
supposed to acquire any per-subsystem hotcpu mutex ( Eg. workqueue_mutex
in kernel/workqueue.c ).

During the CPU_LOCK_RELEASE release event the cpu-hotplug-aware subsystem
is supposed to release the per-subsystem hotcpu mutex.

The reasons for defining new events as opposed to reusing the existing events
like CPU_UP_PREPARE/CPU_UP_FAILED/CPU_ONLINE for locking/unlocking of
per-subsystem hotcpu mutexes are as follow:

	- CPU_LOCK_ACQUIRE: All hotcpu mutexes are taken before subsystems
	start handling pre-hotplug events like CPU_UP_PREPARE/CPU_DOWN_PREPARE
	etc, thus ensuring a clean handling of these events.

	- CPU_LOCK_RELEASE: The hotcpu mutexes will be released only after
	all subsystems have handled post-hotplug events like CPU_DOWN_FAILED,
	CPU_DEAD,CPU_ONLINE etc thereby ensuring that there are no subsequent
	clashes amongst the interdependent subsystems after a cpu hotplugs.

This patch also uses __raw_notifier_call chain in _cpu_up to take care
of the dependency between the two consequetive calls to
raw_notifier_call_chain.

[akpm@linux-foundation.org: fix a bug]
Signed-off-by: NGautham R Shenoy <ego@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since 2.6.18-something, the community has been bugged by the problem to
provide a clean and a stable mechanism to postpone a cpu-hotplug event as
lock_cpu_hotplug was badly broken.

This is another proposal towards solving that problem.  This one is along the
lines of the solution provided in kernel/workqueue.c

Instead of having a global mechanism like lock_cpu_hotplug, we allow the
subsytems to define their own per-subsystem hot cpu mutexes.  These would be
taken(released) where ever we are currently calling
lock_cpu_hotplug(unlock_cpu_hotplug).

Also, in the per-subsystem hotcpu callback function,we take this mutex before
we handle any pre-cpu-hotplug events and release it once we finish handling
the post-cpu-hotplug events.  A standard means for doing this has been
provided in [PATCH 2/4] and demonstrated in [PATCH 3/4].

The ordering of these per-subsystem mutexes might still prove to be a
problem, but hopefully lockdep should help us get out of that muddle.

The patch set to be applied against linux-2.6.19-rc5 is as follows:

[PATCH 1/4] :	Extend notifier_call_chain with an option to specify the
		number of notifications to be sent and also count the
		number of notifications actually sent.

[PATCH 2/4] :	Define events CPU_LOCK_ACQUIRE and CPU_LOCK_RELEASE
		and send out notifications for these in _cpu_up and
		_cpu_down. This would help us standardise the acquire and
		release of the subsystem locks in the hotcpu
		callback functions of these subsystems.

[PATCH 3/4] :	Eliminate lock_cpu_hotplug from kernel/sched.c.

[PATCH 4/4] :	In workqueue_cpu_callback function, acquire(release) the
		workqueue_mutex while handling
		CPU_LOCK_ACQUIRE(CPU_LOCK_RELEASE).

If the per-subsystem-locking approach survives the test of time, we can expect
a slow phasing out of lock_cpu_hotplug, which has not yet been eliminated in
these patches :)

This patch:

Provide notifier_call_chain with an option to call only a specified number of
notifiers and also record the number of call to notifiers made.

The need for this enhancement was identified in the post entitled
"Slab - Eliminate lock_cpu_hotplug from slab"
(http://lkml.org/lkml/2006/10/28/92) by Ravikiran G Thirumalai and
Andrew Morton.

This patch adds two additional parameters to notifier_call_chain API namely
 - int nr_to_calls : Number of notifier_functions to be called.
 		     The don't care value is -1.

 - unsigned int *nr_calls : Records the total number of notifier_funtions
			    called by notifier_call_chain. The don't care
			    value is NULL.

[michal.k.k.piotrowski@gmail.com: build fix]
Credit: Andrew Morton <akpm@osdl.org>
Signed-off-by: NGautham R Shenoy <ego@in.ibm.com>
Signed-off-by: NMichal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

relay doesn't need to use schedule_delayed_work() for waking readers
when a simple timer will do.
Signed-off-by: NTom Zanussi <zanussi@comcast.net>
Cc: Satyam Sharma <satyam.sharma@gmail.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

(akpm: bypassed maintainers, sorry.  There are other patches which depend on
this)

Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

(akpm: bypassed maintainers, sorry.  There are other patches which depend on
this)

Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Switch e1000 over to flush_work_keventd().  This probably fixes a netdev-close
versus linkwatch rtnl_lock() deadlock which nobody knew about.

(akpm: bypassed maintainers, sorry.  There are other patches which depend on
this)

Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Acked-by: NAuke Kok <auke-jan.h.kok@intel.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert tg3 over to flush_work_keventd().  Remove nasty now-unneeded deadlock
avoidance logic.

(akpm: bypassed maintainers, sorry.  There are other patches which depend on
this)

Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Switch the kblockd flushing from a global flush to a more specific
flush_work().

(akpm: bypassed maintainers, sorry.  There are other patches which depend on
this)

Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Jens Axboe <axboe@suse.de>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Migrate AIO over to use flush_work().

Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Zach Brown <zach.brown@oracle.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now when we have ->current_work we can avoid adding a barrier and waiting
for its completition when cwq's queue is empty.

Note: this change is also useful if we change flush_workqueue() to also
check the dead CPUs.
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: Srivatsa Vaddagiri <vatsa@in.ibm.com>
Cc: Gautham Shenoy <ego@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Srivatsa Vaddagiri <vatsa@in.ibm.com>
Cc: Gautham Shenoy <ego@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A basic problem with flush_scheduled_work() is that it blocks behind _all_
presently-queued works, rather than just the work whcih the caller wants to
flush.  If the caller holds some lock, and if one of the queued work happens
to want that lock as well then accidental deadlocks can occur.

One example of this is the phy layer: it wants to flush work while holding
rtnl_lock().  But if a linkwatch event happens to be queued, the phy code will
deadlock because the linkwatch callback function takes rtnl_lock.

So we implement a new function which will flush a *single* work - just the one
which the caller wants to free up.  Thus we avoid the accidental deadlocks
which can arise from unrelated subsystems' callbacks taking shared locks.

flush_work() non-blockingly dequeues the work_struct which we want to kill,
then it waits for its handler to complete on all CPUs.

Add ->current_work to the "struct cpu_workqueue_struct", it points to
currently running "struct work_struct". When flush_work(work) detects
->current_work == work, it inserts a barrier at the _head_ of ->worklist
(and thus right _after_ that work) and waits for completition. This means
that the next work fired on that CPU will be this barrier, or another
barrier queued by concurrent flush_work(), so the caller of flush_work()
will be woken before any "regular" work has a chance to run.

When wait_on_work() unlocks workqueue_mutex (or whatever we choose to protect
against CPU hotplug), CPU may go away. But in that case take_over_work() will
move a barrier we queued to another CPU, it will be fired sometime, and
wait_on_work() will be woken.

Actually, we are doing cleanup_workqueue_thread()->kthread_stop() before
take_over_work(), so cwq->thread should complete its ->worklist (and thus
the barrier), because currently we don't check kthread_should_stop() in
run_workqueue(). But even if we did, everything should be ok.

[akpm@osdl.org: cleanup]
[akpm@osdl.org: add flush_work_keventd() wrapper]
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove ->remove_sequence, ->insert_sequence, and ->work_done from struct
cpu_workqueue_struct.  To implement flush_workqueue() we can queue a
barrier work on each CPU and wait for its completition.

The barrier is queued under workqueue_mutex to ensure that per cpu
wq->cpu_wq is alive, we drop this mutex before going to sleep.  If CPU goes
down while we are waiting for completition, take_over_work() will move the
barrier on another CPU, and the handler will wake up us eventually.
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We take workqueue_mutex in there to keep CPU hotplug away.  But
preempt_disable() will suffice for that.

Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now that the cpu_is_xxx() macros are available both on AVR32 and AT91, we can
remove a couple of #ifdefs from this driver.  One of them is actually wrong --
new_1 should be set on AVR32 but isn't.  This causes the bus clock to run at
twice the speed it is configured to.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Cc: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Several drivers shared between AT91 and AVR32 chips use cpu_is_xxx()
to handle CPU-specific differences. Currently, such code needs to be
inside #ifdef CONFIG_ARCH_AT91 because the macros don't exist on AVR32.

By defining the same macros on both AT91 and AVR32, these #ifdefs can
be eliminated. Since the macros will evaluate to a constant value for
CPUs that aren't supported by the current architecture, any code that
is only needed on AT91 will be optimized away on AVR32 and vice versa.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Cc: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Implement support for writing to regular AFS files, including:

 (1) write

 (2) truncate

 (3) fsync, fdatasync

 (4) chmod, chown, chgrp, utime.

AFS writeback attempts to batch writes into as chunks as large as it can manage
up to the point that it writes back 65535 pages in one chunk or it meets a
locked page.

Furthermore, if a page has been written to using a particular key, then should
another write to that page use some other key, the first write will be flushed
before the second is allowed to take place.  If the first write fails due to a
security error, then the page will be scrapped and reread before the second
write takes place.

If a page is dirty and the callback on it is broken by the server, then the
dirty data is not discarded (same behaviour as NFS).

Shared-writable mappings are not supported by this patch.

[akpm@linux-foundation.org: fix a bunch of warnings]
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make some miscellaneous changes to the AFS filesystem:

 (1) Assert RCU barriers on module exit to make sure RCU has finished with
     callbacks in this module.

 (2) Correctly handle the AFS server returning a zero-length read.

 (3) Split out data zapping calls into one function (afs_zap_data).

 (4) Rename some afs_file_*() functions to afs_*() where they apply to
     non-regular files too.

 (5) Be consistent about the presentation of volume ID:vnode ID in debugging
     output.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Export a couple of core functions for AFS write support to use:

	find_get_pages_contig()
	find_get_pages_tag()
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

u64 and s64 are not necessarily 'long long' on some 64-bit
platforms, so explicit the type to kill the compiler warnings.

Also consistently use '%Lu' which is unsigned.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Get the kernel version string only once from the environment, thus slightly
speeding up kernel-doc.
Signed-off-by: NBorislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It seems that we need to clarify that a patch series is a series of related
patches rather than "here are some of my patches as multiple (numbered)
emails."
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since path_walk sets the total_link_count to 0 and calls link_path_walk, we
can just call path_walk directly.
Signed-off-by: NJosef 'Jeff' Sipek <jsipek@cs.sunysb.edu>
Acked-by: NChristoph Hellwig <hch@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJosef 'Jeff' Sipek <jsipek@cs.sunysb.edu>
Acked-by: NChristoph Hellwig <hch@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There's more that need fixing, and fix my own subject spelling error too.
Signed-off-by: NDaniel Walker <dwalker@mvista.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It's not sane to use mutex_lock_interruptible() and to then ignore the result.

Ditto down_interruptible(), but I'm lazy.

Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix tty_set_ldisc in tty_io.c so that tty->receive_room is only cleared if
actually changing line disciplines.

Without this fix a problem occurs when requesting the line discipline to
change to the same line discipline.  In this case tty->receive_room is
cleared but ldisc->open() is not called to set tty->receive_room back to a
sane value.  The result is that tty->receive_room is stuck at 0 preventing
the tty flip buffer from passing receive data to the line discipline.

For example: a switch from N_TTY to N_TTY followed by a select() call for
read input results in data never being received because tty->receive_room
is stuck at zero.

A switch from N_TTY to N_TTY followed by a read() call works because the
read() call itself sets tty->receive_room correctly (but select does not).

Previously (< 2.6.18) this was not a problem because the tty flip buffer
pushed data to the line discipline without regard for tty->receive room.
Signed-off-by: NPaul Fulghum <paulkf@microgate.com>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch moves the sig_kernel_* and related macros from kernel/signal.c
to linux/signal.h, and cleans them up slightly.  I need the sig_kernel_*
macros for default signal behavior in the utrace code, and want to avoid
duplication or overhead to share the knowledge.
Signed-off-by: NRoland McGrath <roland@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

[akpm@linux-foundation.org: fix it]
Signed-off-by: NWANG Cong <xiyou.wangcong@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Driver for the on-chip hardware random number generator on PA Semi
PA6T-1682M.
Signed-off-by: NEgor Martovetsky <egor@pasemi.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When cpuset is configured, it breaks the strict hugetlb page reservation as
the accounting is done on a global variable.  Such reservation is
completely rubbish in the presence of cpuset because the reservation is not
checked against page availability for the current cpuset.  Application can
still potentially OOM'ed by kernel with lack of free htlb page in cpuset
that the task is in.  Attempt to enforce strict accounting with cpuset is
almost impossible (or too ugly) because cpuset is too fluid that task or
memory node can be dynamically moved between cpusets.

The change of semantics for shared hugetlb mapping with cpuset is
undesirable.  However, in order to preserve some of the semantics, we fall
back to check against current free page availability as a best attempt and
hopefully to minimize the impact of changing semantics that cpuset has on
hugetlb.
Signed-off-by: NKen Chen <kenchen@google.com>
Cc: Paul Jackson <pj@sgi.com>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Cleanup using simple_read_from_buffer() for /dev/cpuset/tasks and
/proc/config.gz.

Cc: Paul Jackson <pj@sgi.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Cleanup using simple_read_from_buffer() in binfmt_misc, configfs, and sysfs.

Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Joel Becker <joel.becker@oracle.com>
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Cleanup using bitrev8 in cm4000_cs driver.

Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes error paths in module_init and probe functions in cm4000_cs
and cm4040_cs drivers.

Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The MCA bus has a few "integrated" functions, which are effectively virtual
slots on the bus.  The problem is that these special functions don't have
dedicated pos IDs, so we have to manufacture ids for them outside the pos
space ...  and these ids can't be matched by the standard matching function,
so add a special registration that requests a list of pos ids or a particular
integrated function.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There's a bug in the MCA bus matching algorithm in that it promotes from
signed short to int before comparing with the actual id and does sign
extension on anything > 0x7fff (which means that pos ids > 0x7fff never get
correctly matched).
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Always ask the hardware to determine the hardware processor id in both UP and
SMP kernels.
Signed-off-by: NFernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>