This busy_wait is not needed after latest changes
to the cs4231-lib
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

This header file exists only for some hacks to adapt alsa-driver
tree.  It's useless for building in the kernel.  Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it.  This should be really killed in
future.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

This patch enables wavetable chips ES689/ES69X connected to
ESS ES18xx chips. The wavetable chip uses FM DAC if the clock signal
from the wavetable is active.
It has no effect if there is no ESS wavetable chip present.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

sound/isa/sb/sb16_csp.c: In function ‘snd_sb_csp_new’:
sound/isa/sb/sb16_csp.c:121: warning: ‘version’ may be used uninitialized in this function
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

This removes the pnp_resource_change use from the ALSA ISAPnP drivers. In
2.4 these were useful in providing an easy path to setting the resources,
but in 2.6 they retain function as a layering violation only.
This makes for a nice cleanup (-550 lines) of ALSA but moreover, ALSA is the
only remaining user of pnp_init_resource_table(), pnp_resource_change() and
pnp_manual_config_dev() (and, in fact, of 'struct pnp_resource_table') in
the tree outide of drivers/pnp itself meaning it makes for more cleanup
potential inside the PnP layer.
Thomas Renninger acked their removal from that side, you did from the ALSA
side (CC list just copied from that thread).
Against current alsa-kernel HG. Many more potential cleanups in there, but
this _only_ removes the pnp_resource_change code. Compile tested against
current alsa-kernel HG and compile- and use-tested against 2.6.23.x (few
offsets).
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: NRene Herman <rene.herman@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Check the value ranges in ctl put callbacks properly (in the rest drivers).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Remove sequencer instrument layer from the tree.
This mechanism hasn't been used much with the actual devices.  The only
reasonable user was OPL3 loader, and now it was rewritten to use hwdep
instead.  So, let's remove the rest of rotten codes.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Fixed the print format for debug message.
Spotted by Matthew Wilcox.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>

The last patches to replace with schedule_timeout() don't work as expected.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

the BTC 1817DW board.
The QS1000 is connected through the digital input
to the Opti931 chip.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

open and close operations are called only from pcm layer
and mutexed there with pcm->open_mutex.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

when simulating a storm of fake GUS interrupts (without actually owning
this venerable piece of ISA hardware) the driver falls over (crashes) in
two ways:
1) spinlocks being initialized too late:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
 [<401058ca>] show_trace_log_lvl+0x1a/0x30
 [<401064b2>] show_trace+0x12/0x20
 [<401064d6>] dump_stack+0x16/0x20
 [<4014a72b>] __lock_acquire+0xcfb/0x1030
 [<4014aac0>] lock_acquire+0x60/0x80
 [<40721a68>] _spin_lock_irqsave+0x38/0x50
 [<4058fc12>] snd_gf1_i_look8+0x22/0x60
 [<405906fe>] snd_gus_interrupt+0x13e/0x270
 [<401548e8>] handle_IRQ_event+0x28/0x60
 [<40155cc1>] handle_fasteoi_irq+0x71/0xe0
 [<40107238>] do_IRQ+0x48/0xa0
 [<401051fe>] common_interrupt+0x2e/0x40
 [<40156822>] register_handler_proc+0x92/0xf0
 [<401550c2>] setup_irq+0xe2/0x190
 [<40155224>] request_irq+0xb4/0xd0
 [<4058f524>] snd_gus_create+0x124/0x3c0
 [<40aa4087>] snd_gusclassic_probe+0x2a7/0x4b0
 [<403f5eff>] isa_bus_probe+0x1f/0x30
 [<403f1944>] driver_probe_device+0x84/0x190
 [<403f1a58>] __device_attach+0x8/0x10
 [<403f0e63>] bus_for_each_drv+0x53/0x80
 [<403f1b1b>] device_attach+0x8b/0x90
 [<403f0dd8>] bus_attach_device+0x48/0x80
 [<403efdbd>] device_add+0x45d/0x5a0
 [<403eff12>] device_register+0x12/0x20
 [<403f60c3>] isa_register_driver+0xb3/0x140
 [<40aa3dd2>] alsa_card_gusclassic_init+0x12/0x20
 [<40a665c3>] kernel_init+0x133/0x310
 [<401054a7>] kernel_thread_helper+0x7/0x10
 =======================
2) callback functions not being filled in yet:
BUG: unable to handle kernel NULL pointer dereference at virtual address 00000000
 printing eip:
00000000
*pde = 00000000
Oops: 0000 [#1]
SMP DEBUG_PAGEALLOC
CPU:    0
EIP:    0060:[<00000000>]    Not tainted VLI
EFLAGS: 00010002   (2.6.23 #37)
EIP is at 0x0
eax: 7fe94000   ebx: 7fe94000   ecx: 00000000   edx: 00000226
esi: 00000000   edi: 00000005   ebp: 7ff87c28   esp: 7ff87bf4
ds: 007b   es: 007b   fs: 00d8  gs: 0000  ss: 0068
Process swapper (pid: 1, ti=7ff86000 task=7ff84000 task.ti=7ff86000)
Stack: 40590683 408424a9 408db87c 00000029 40787406 00000064 00000046 ff000000
       000000ff 00000001 7faefaf0 00000000 00000005 7ff87c40 401548e8 00000000
       40a52000 7faefaf0 00000005 7ff87c58 40155cc1 40a52030 00000005 00000000
Call Trace:
 [<401058ca>] show_trace_log_lvl+0x1a/0x30
 [<4010598b>] show_stack_log_lvl+0xab/0xd0
 [<40105b7c>] show_registers+0x1cc/0x2d0
 [<40105d96>] die+0x116/0x240
 [<4011d7bb>] do_page_fault+0x18b/0x670
 [<40721d22>] error_code+0x72/0x80
 [<401548e8>] handle_IRQ_event+0x28/0x60
 [<40155cc1>] handle_fasteoi_irq+0x71/0xe0
 [<40107238>] do_IRQ+0x48/0xa0
 [<401051fe>] common_interrupt+0x2e/0x40
 [<401a344e>] proc_create+0x3e/0x120
 [<401a3733>] proc_mkdir_mode+0x23/0x50
 [<401a376f>] proc_mkdir+0xf/0x20
 [<40156864>] register_handler_proc+0xd4/0xf0
 [<401550c2>] setup_irq+0xe2/0x190
 [<40155224>] request_irq+0xb4/0xd0
 [<4058f524>] snd_gus_create+0x124/0x3c0
 [<40aa4087>] snd_gusclassic_probe+0x2a7/0x4b0
 [<403f5eff>] isa_bus_probe+0x1f/0x30
 [<403f1944>] driver_probe_device+0x84/0x190
 [<403f1a58>] __device_attach+0x8/0x10
 [<403f0e63>] bus_for_each_drv+0x53/0x80
 [<403f1b1b>] device_attach+0x8b/0x90
 [<403f0dd8>] bus_attach_device+0x48/0x80
 [<403efdbd>] device_add+0x45d/0x5a0
 [<403eff12>] device_register+0x12/0x20
 [<403f60c3>] isa_register_driver+0xb3/0x140
 [<40aa3dd2>] alsa_card_gusclassic_init+0x12/0x20
 [<40a665c3>] kernel_init+0x133/0x310
 [<401054a7>] kernel_thread_helper+0x7/0x10
 =======================
Code:  Bad EIP value.
EIP: [<00000000>] 0x0 SS:ESP 0068:7ff87bf4
Kernel panic - not syncing: Fatal exception in interrupt
with these things fixed, i get the expected 'no such hardware' result
from the driver initialization:
 Calling initcall 0x40aa3dc0: alsa_card_gusclassic_init+0x0/0x20()
 ALSA sound/isa/gus/gusclassic.c:136: [0x220] check 1 failed - 0xff
 initcall 0x40aa3dc0: alsa_card_gusclassic_init+0x0/0x20() returned 0.
 initcall 0x40aa3dc0 ran for 133 msecs:
 alsa_card_gusclassic_init+0x0/0x20()
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Signed-off-by: NJaroslav Kysela <perex@perex.cz>

The polling loop to check for ACI to go down was more convoluted than it
needed to be.  New loop should be more efficient and it is a lot simpler.  The
old loop checked for a timeout before checking for ACI down, which could
result in an erroneous timeout.  It's only a failure if the timeout expires
_and_ ACI is still high.  There is nothing wrong with the timeout expiring
while the task is sleeping if ACI went low.
A polling loop to check for the device to leaving INIT mode is removed.  The
device must have already left init for the previous ACI loop to have finished.
Acked-by: NRene Herman <rene.herman@gmail.com>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Simplest fix.
Acked-by: NRene Herman <rene.herman@gmail.com>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Fix schedule_timeout() use in alsa-kernel. Mostly just
	schedule_timeout(1) --> schedule_timeout_uninterruptible(1)
The wavefront_synth one fixes the surrounding loop as well. In ymfpci_main,
delete a superfluous set_current_state() and in soc/soc-dapm.c replace an
_interruptible with _uninterruptible in some debug code; it's not waiting
for signals.

Signed-off-by: Rene Herman <rene.herman>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch adds support for audio part of the Ensoniq
SoundScape VIVO cards. The MIDI part is not supported.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

The OPTi ISA-PnP chips advertise their OPL4 base at 0x380 (to 0x3f0) through
pnp and put their on-chip OPL3 at +8. The driver assumes the provided
value is the ALBase (OPL3 address) though and checks for an OPL4 at -8,
which means that simply adding 8 to the pnp provides value works to fix
detection of both OPL3 and OPL4.
Problem spotted on 931 and 933 by Krzysztof Helt and confirmed on 924 and
925 (together all OPTi ISA-PnP chips) by me.
Signed-off-by; Rene Herman <rene.herman@gmail.com>
Acked-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch adds second DMA channel and WSS port settings
to the sscape driver. Also, it adds internal card type setting.
The Ensoniq SoundScape VIVO PnP id is added but not handled
yet.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch zeroes buffer for the card name and
fixes incorrect jump in the probe function.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch fixes ad1848_lib waiting loops to be the same as in the cs4231_lib.
Acked-by: NRene Herman <rene.herman@gmail.com>
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

sound/isa/sc6000.c: In function 'sc6000_dsp_reset':
sound/isa/sc6000.c:270: error: implicit declaration of function 'udelay'        sound/isa/sc6000.c: In function 'sc6000_init_mss':
sound/isa/sc6000.c:327: error: implicit declaration of function 'msleep'
{standard input}: Assembler messages:
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This is port of the Gallant SC-6000 driver from the OSS aedsp16 driver.
This card was also sold as AudioExcel DSP 16 and Zoltrix AV302 (Audio
Plus True 16).
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch replaces long msleeps in waiting loops
with schedule_timeout() calls.

Signed-off-by: Krzysztof Helt <krzysztof.h1 at wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

While I'm at it another 'while I'm there' -- replace commented out debug
code with snd-printd{,d}.
Signed-off-by: NRene Herman <rene.herman@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

If I'm not mistaken, any (new) use of HZ these days is considered a bug so
while I'm there...
Signed-off-by: NRene Herman <rene.herman@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

When the ad1848/cs2431 is first being initialized, auto-calibration may not
be set causing a timeout waiting for it in snd_ad1848/cs4231_mce_down().
This has no dire consequences other than an alarming printk, but since what
we need to wait for is for the calibration to _finish_, let's just check for
that instead.
The early chips need a slight delay (as commented -- 5 sample periods) to be
sure that _if_ calibration is going to happen, it has started when we check
While the CS4231A datasheet implies it'll happen immediately on downing MCE,
some testing is showing that there's a window there as well, so just do the
delay everywhere.
Thanks to Krysztof Helt for pinpointing this problem.
Signed-off-by: NRene Herman <rene.herman@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch replaces a common delay loop by a function.
It also uses ARRAY_SIZE macro for the rates table.
Acked-by: NRene Herman <rene.herman@gmail.com>
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch replaces a common delay loop by a function.
It also uses ARRAY_SIZE macro for the rates table.
Acked-by: NRene Herman <rene.herman@gmail.com>
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

CS5530 is a PCI device and often shares the IRQ although the SB common
routine tries to allocate it exclusively.  This patch allows shared IRQ
for CS5530.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Use the standard firmware loader for loading ICS2115 OS firmware file.
This is the last old bad guy that is still using sys_open() and sys_read()
calls, and now all should be gone.
The patch also adds the missing description of module options related
with wavefront_synth.c.
Due to this rewrite, user will have to copy or make symlink the firmware
file appropriately to the standard firmware path such as /lib/firmware.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Set the SNDRV_PCM_INFO_SYNC_START flag and the substream's sync ID
(only) if the substream actually can be linked to another one.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch uses the Kconfig parameters SND_AD1848_LIB and
SND_CS4231_LIB instead of mentioning each driver that requires
the ad1848-lib or cs4231-lib separately in the Makefiles.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

As reported by Troy Heidner, the 'Gateway Solo 5150' laptop (for one) has an
onboard ESS1879 that identifies itself through PNPBIOS as just that. He also
confirmed that other than not knowing about it, snd-es18xx drives the chip
fine, so this adds the ID to the driver.
Signed-off-by: NRene Herman <rene.herman@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

The mode change / recalibration doesn't work always with opl3sa2 devices,
e.g. the first time it's played back.  The patch fixes the problem.
Signed-off-by: NPaul Vojta <vojta@math.berkeley.edu>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Clean up codes using the new common snd_ctl_boolean_*_info() callbacks.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>