Driver for the PCA9633 I2C chip supporting four LEDs and 255 brightness
levels.

[akpm@linux-foundation.org: fix kcalloc() call]
[axel.lin@gmail.com: fix kcalloc parameters swapped]
Signed-off-by: NPeter Meerwald <p.meerwald@bct-electronic.com>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add platform driver for the Soekris Engineering net5501 single-board
computer.  Probes well-known locations in ROM for BIOS signature
to confirm correct platform.  Registers 1 LED and 1 GPIO-based
button (typically used for soft reset).
Signed-off-by: NPhilip Prindeville <philipp@redfish-solutions.com>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Andres Salomon <dilinger@queued.net>
Cc: Matthew Garrett <mjg@redhat.com>
[ Removed Kconfig and Makefile detritus from drivers/leds/]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-jv5uf34996juqh5syes8mn4h@git.kernel.orgSigned-off-by: NIngo Molnar <mingo@elte.hu>

Add support for leds on Bachmann's ot200 visualisation device.  The
device has three leds on the back panel (led_err, led_init and led_run)
and can handle up to seven leds on the front panel.

The driver was written by Linutronix on behalf of Bachmann electronic
GmbH.  It incorporates feedback from Lars-Peter Clausen

[akpm@linux-foundation.org: add dependency on HAS_IOMEM]
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NChristian Gmeiner <christian.gmeiner@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

TI's TCA6507 is the LED driver in the GTA04 Openmoko motherboard.  The
driver provides full support for brightness levels and hardware blinking.

This driver can drive each of 7 outputs as an LED or a GPIO output,
and provides hardware-assist blinking.

[akpm@linux-foundation.org: fix __mod_i2c_device_table alias]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NNeilBrown <neilb@suse.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch enables LED controller in MAX8997 PMIC.
Signed-off-by: NDonggeun Kim <dg77.kim@samsung.com>
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This driver is no longer needed after the Amstrad Delta on-board LED
devices have been converted to leds-gpio compatible.
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add V2 of the LED driver for a single timer channel for the TPU hardware
block commonly found in Renesas SoCs.

The driver has been written with optimal Power Management in mind, so to
save power the LED is driven as a regular GPIO pin in case of maximum
brightness and power off which allows the TPU hardware to be idle and
which in turn allows the clocks to be stopped and the power domain to be
turned off transparently.

Any other brightness level requires use of the TPU hardware in PWM mode.
TPU hardware device clocks and power are managed through Runtime PM.
System suspend and resume is known to be working - during suspend the LED
is set to off by the generic LED code.

The TPU hardware timer is equipeed with a 16-bit counter together with an
up-to-divide-by-64 prescaler which makes the hardware suitable for
brightness control.  Hardware blink is unsupported.

The LED PWM waveform has been verified with a Fluke 123 Scope meter on a
sh7372 Mackerel board.  Tested with experimental sh7372 A3SP power domain
patches.  Platform device bind/unbind tested ok.

V2 has been tested on the DS2 LED of the sh73a0-based AG5EVM.

[axel.lin@gmail.com: include linux/module.h]
Signed-off-by: NMagnus Damm <damm@opensource.se>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This new driver replaces the old PCEngines Alix 2/3 LED driver with a
new driver that controls the LEDs through the leds-gpio driver. The
old driver accessed GPIOs directly, which created a conflict and
prevented also loading the cs5535-gpio driver to read other GPIOs on
the Alix board. With this new driver, we hook into leds-gpio which in
turn uses GPIO to control the LEDs and therefore it's possible to
control both the LEDs and access onboard GPIOs

Driver is moved to platform/geode as requested by Grant and any other
geode initialisation modules should move here also

This driver is inspired by leds-net5501.c by Alessandro Zummo.

Ideally, leds-net5501.c should also be moved to platform/geode. 
Additionally the driver relies on parts of the patch: 7f131cf3 ("leds:
leds-alix2c - take port address from MSR) by Daniel Mack to perform
detection of the Alix board.

[akpm@linux-foundation.org: include module.h]
Signed-off-by: NEd Wildgoose <kernel@wildgooses.com>
Cc: git@wildgooses.com
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Reviewed-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Add LED support for the HTC ASIC3. Underlying support is provided by the mfd/asic3 and leds/leds-asic3 drivers. An example configuration is provided by the pxa/hx4700 platform.
Signed-off-by: NPaul Parsons <lost.distance@yahoo.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This function makes a deep copy of the platform data to allow it to live
in init memory.  For a kernel that supports several machines and so
includes the definition for several leds-gpio devices this saves quite
some memory because all but one definition can be free'd after boot.

As the function is used by arch code it must be builtin and so cannot go
into leds-gpio.c.

[akpm@linux-foundation.org: s/CONFIG_LED_REGISTER_GPIO/CONFIG_LEDS_REGISTER_GPIO/]
Signed-off-by: NUwe Kleine-König  <u.kleine-koenig@pengutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: NRichard Purdie <richard.purdie@linuxfoundation.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: NH Hartley Sweeten <hartleys@visionengravers.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The H1940 machine now uses leds-gpio and leds-h1940 has no users anymore.
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Cc: "Arnaud Patard (Rtp)" <arnaud.patard@rtp-net.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Simple backlight driver for National Semiconductor LM3530.  Presently only
manual mode is supported, PWM and ALS support to be added.
Signed-off-by: NShreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Provide configuration and compilation support for LP5521 and LP5523
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch add a LED class driver for LEDs found on the LaCie 2Big and
5Big Network v2 boards. The LEDs are wired to a CPLD and are controlled
through a GPIO extension bus.
Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

This patch add a LED class driver for the dual-GPIO LEDs found on the
Network Space v2 board (and parents). This include Internet Space v2,
Network Space (Max) v2 and d2 Network v2 boards.

This dual-GPIO LED is wired to a CPLD and can blink in relation with the
SATA activity. The driver expose this capability through a "sata" sysfs
attribute.
Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

This add basic led support for Freescale MC13783 PMIC.
Signed-off-by: NPhilippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

It is based on the previously submitted code by Alessandro Zummo, but is
changed to use the new GPIO driver with 2.6.33, and the driver has been
moved to drivers/leds where it belongs.

[akpm@linux-foundation.org: coding-style fixes]
[randy.dunlap@oracle.com: fix net5501 kconfig]
Signed-off-by: NBjarke Istrup Pedersen <gurligebis@gentoo.org>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

This patch adds an LED driver to support the Dell Activity LED on the
Dell Latitude 2100 netbook and future products to come. The Activity LED
is visible externally in the lid so classroom instructors can observe it
from a distance. The driver uses the sysfs led_class and provides a
standard LED interface.

Signed-off by: Bob Rodgers <Robert_Rodgers@dell.com>
Signed-off-by: NLouis Davis <Louis_Davis@dell.com>
Signed-off-by: Jim Dailey <Jim_Dailey@dell.com>, Developers
Acked-by: NMatthew Garrett <mjg@redhat.com>
Acked-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Enable led sub device in Marvell 88PM860x. Two LED arrays can be supported.
Each LED array can be used for R,G,B leds.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This driver provides an interface for controlling LEDs (or vibrators)
connected to PMICs for which there is a regulator framework driver.

This driver can be used, for instance, to control vibrator on all Motorola EZX
phones using the pcap-regulator driver services.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The LT3593 is a step-up DC/DC converter designed to drive up to ten
white LEDs in series. The current flow can be set with a control pin.

This driver controls any number of such devices connected on generic
GPIOs and exports the function as as platform_driver.

The gpio_led platform data struct definition is reused for this purpose.

Successfully tested on a PXA embedded board.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

This code is based on a driver that came in the "Open-source
and GPL components" download here:

http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Server+Products&ProductLine=Intel%C2%AE+Storage+Systems&ProductProduct=Intel%C2%AE+Entry+Storage+System+SS4200-E&OSVersion=OS+Independent

It was in a file called nasgpio.c inside of a second zip file
called SS4200-E_Linux_SIO_Driver-v1.4.zip and is based on this
updated to use the LED subsystem with the ioctl and hardware
monitor support removed.

I don't have any need for brightness
control, and its code is *completely* separate from the on/off
controls implemented here.  If anyone else wants it, I'd be
happy to look into adding it, but I don't care enough for now.

Except for the probe routines, I rewrote most of it.  I also
Note that I don't have any hardware documentation except for
the original driver.

Thanks go to Arjan for his help in getting the original source
for this released and for chasing down some licensing issues.
Signed-off-by: NDave Hansen <dave@sr71.net>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The WM831x devices feature two software controlled status LEDs with
hardware assisted blinking.

The device can also autonomously control the LEDs based on a selection
of sources.  This can be configured at boot time using either platform
data or the chip OTP.  A sysfs file in the style of that for triggers
allowing the control source to be configured at run time.  Triggers
can't be used here since they can't depend on the implementation details
of a specific LED type.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

LEDs driver for National Semiconductor LP3944 Funlight Chip
http://www.national.com/pf/LP/LP3944.html

This helper chip can drive up to 8 leds, with two programmable DIM
modes; it could even be used as a gpio expander but this driver assumes
it is used as a led controller.

The DIM modes are used to set _blink_ patterns for leds, the pattern is
specified supplying two parameters:
  - period: from 0s to 1.6s
  - duty cycle: percentage of the period the led is on, from 0 to 100

LP3944 can be found on Motorola A910 smartphone, where it drives the rgb
leds, the camera flash light and the displays backlights.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

ROHM BD2802GU is a RGB LED controller attached to i2c bus and specifically
engineered for decoration purposes.  This RGB controller incorporates
lighting patterns and illuminates.

This driver is designed to minimize power consumption, so when there is no
emitting LED, it enters to reset state.  And because the BD2802GU has lots
of features that can't be covered by the current LED framework, it
provides Advanced Configuration Function(ADF) mode, so that user
applications can set registers of BD2802GU directly.

Here are basic usage examples :
; to turn on LED (not blink)
$ echo 1 > /sys/class/leds/led1_R/brightness
; to blink LED
$ echo timer > /sys/class/leds/led1_R/trigger
$ echo 1 > /sys/class/leds/led1_R/delay_on
$ echo 1 > /sys/class/leds/led1_R/delay_off
; to turn off LED
$ echo 0 > /sys/class/leds/led1_R/brightness

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NKim Kyuwon <chammoru@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The gpio led trigger will allow leds to be triggered by
gpio events.

When we give the led a gpio number, the trigger will
request_irq() on that so we don't have to keep polling
for gpio state.

It's useful for usecases as n810's keypad leds that could
be triggered by the gpio event generated when user slides
up to show the keypad.

We also provide means for userland to tell us what is the
desired brightness for that special led when it goes on
so userland could use information from ambient light sensors
and not set led brightness too high if it's not necessary.
Signed-off-by: NFelipe Balbi <me@felipebalbi.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Mikrotik built six LEDs into the Routerboard 532, from which one is
destined for custom use, the so called "User LED". This patch adds a
driver for it, based on the LEDs class.
Signed-off-by: NPhil Sutter <n0-1@freewrt.org>
Acked-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Add a simple driver for pwm driver LEDs.  pwm_id and period can be defined
in board file.  It is developed for pxa, however it is probably generic
enough to be used on other platforms with pwm.
Signed-off-by: NLuotao Fu <l.fu@pengutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Add an LED driver using the DAC124S085 DAC from NatSemi

[randy.dunlap@oracle.com: use header files for interfaces]
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Move the second part of the HP laptop disk protection functionality (a red
led) to the same driver.  From a purely Linux developer's point of view,
the led and the accelerometer have nothing related.  However, they
correspond to the same ACPI functionality, and so will always be used
together, moreover as they share the same ACPI PNP alias, there is no
other simple to allow to have same loaded at the same time if they are not
in the same module.  Also make it requires the led class to compile and
update the Kconfig text.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The voltage and current regulators on the WM8350 AudioPlus PMIC can be
used in concert to provide a power efficient LED driver.  This driver
implements support for this within the standard LED class.

Platform initialisation code should configure the LED hardware in the
init callback provided by the WM8350 core driver.  The callback should
use wm8350_isink_set_flash(), wm8350_dcdc25_set_mode() and
wm8350_dcdc_set_slot() to configure the operating parameters of the
regulators for their hardware and then then use wm8350_register_led() to
instantiate the LED driver.

This driver was originally written by Liam Girdwood, though it has been
extensively modified since then.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Driver for PC Engines ALIX.2 and ALIX.3 LEDs.
Signed-off-by: NConstantin Baranov <const@mimas.ru>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

HP notebooks contain accelerometer-based disk protection subsystem,
and LED that indicates hard disk is protected. This is driver for the
LED part.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The cm-x270 board uses leds-gpio so remove the now unneeded driver.
Acked-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

This allows LEDs to be controlled as a backlight device where
they turn off and on when the display is blanked and unblanked.
This is useful where you need various key backlight LEDs to
dim at the same time as the backlight.
Signed-off-by: NRodolfo Giometti <giometti@linux.it>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-spitz

Drop leds-spitz.c and the declarations of now un-referenced
spitzscoop_device, spitzscoop2_device.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-corgi

Drop leds-corgi.c and remove the declaration of now un-referenced
corgiscoop_device.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>