The current IEEE802.15.4 stack assumes that a radio will never deliver
packets with a bad CRC into the stack, as required by the standard.
at86rf230 driven radios violates this assumption because of another
incompatibility: devices are required to send ACKs if requested by a
sender, but RF2xx will only send ACKs from a special receive mode that
is currently not used by the driver.

Enable this receive mode to fix both bugs. Frames with bad CRCs will not
be received at all, and ACKs will be sent if so requested.
Signed-off-by: NPhoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the AT86RF2xy chips are mostly compatible, this is only a small
change to the actual driver code. The at86rf230 driver already supports the
RF212 in most places, only three small adjustments are required:

 * force the initial state after P_ON to FORCE_TRX_OFF to work around a
   documented erratum
 * channels_supported depends on the frequency of the transceiver, and
   thus is_rf212
 * do early detection of chip version select an appropriate _ops struct
   based on the chip version.
Signed-off-by: NPhoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.

[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Implemented separate irq handling for edge and level type interrupt
configuration. For edge type interrupts calls to disable_irq_nosync()
and enable_irq() are removed. The at86rf230 resets the irq line only
after the irq status register is read. Disabling the irq can lock the
driver in situations where a irq is set by the radio while the driver
is still reading the frame buffer.

With irq_type configuration set to 0 the original behavior is
preserverd.

Additional the irq filter register is set to filter out all unused
interrupts and the irq status register is read in the probe
function to clear the irq line.
Signed-off-by: NSascha Herrmann <sascha@ps.nvbi.de>

Conflicts:
	drivers/net/ieee802154/at86rf230.c
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add option to at86rf230 platform data to configure the type of the
interrupt used by the driver. The irq polarity of the device will
be configured accordingly.
Signed-off-by: NSascha Herrmann <sascha@ps.nvbi.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In at86rf230_probe() lp was first set to dev->priv and a few lines later
dev->priv was set to lp again, without changing lp in between. The call
to ieee802154_unregister_device() before err_irq: was unreachable.
Signed-off-by: NSascha Herrmann <sascha@ps.nvbi.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The register names have been wrong since the beginning but it only showed up now
as they are actualy used for the upcoming auto ACK support.
Signed-off-by: NStefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the filter function to update short address, pan id and ieee
address on change. Allowing for hardware address filtering needed for
auto ACK.
Signed-off-by: NStefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to implement empty suspend/resume callbacks if there is nothing
to do during suspend/resume. The drivers will behave the same with no callbacks
or empty callbacks during suspend/resume.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The IEEE 802.15.4 standard represents a networking protocol. I don't
exactly know why drivers for this protocol are stored into the root
'driver' folder, but better will be to store them with other
networking stuff. Currently there are only 3 drivers available for
IEEE 802.15.4 stack, so lets do it now with the smallest overhead.
Signed-off-by: NAlexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code under _init and _exit functions is similar to the code of
module_spi_driver macro, which is a wrapper to the module_driver macro,
so use it instead.
Signed-off-by: NAlexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix LOCKDEP bug message for the irq handler spinlock.
Make the irq processing code more explicit and stable.
Signed-off-by: NAlexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove excessive variable used for the return status.
Signed-off-by: NAlexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The AT86RF231 is a feature rich, low-power 2.4 GHz radio transceiver
designed for industrial and consumer ZigBee/IEEE 802.15.4, 6LoWPAN,
RF4CE and high data rate 2.4 GHz ISM band applications.

This patch adds support for the Atmel RF230/231 radio transceivers.
Signed-off-by: NAlexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>