Add a common entry-macro-vic2.S for systems where there are two VICs
so that the machine or platform directories just need to setup the
correct information before including <asm/entry-macro-vic2.S> into
their own entry-macro.S file.

Since this code is from the S3C64XX project, we update the S3C64XX
machine entry code to use this new header.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the handling for the UART interrupts out of the s3c64xx specific
code and into plat-samsung so that it can be used by all implementations
that need it.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the VIC based timer interrupt handling out of plat-s3c64xx and
into plat-samsung to be re-used for other systems. This also reduces
the code size as we now have a common init routine and use the irq_desc
to store the interrupt number of the timer.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add power management support to the VIC by registering
each VIC as a system device to get suspend/resume
events going.

Since the VIC registeration is done early, we need to
record the VICs in a static array which is used to add
the system devices later once the initcalls are run. This
means there is now a configuration value for the number
of VICs in the system.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add support for saving the state of the IRQ registers over suspend.

This requires moving the S3C64XX UART registers into <plat/regs-serial.h>
and adding irq-pm.c which saves the state of all the IRQ registers.

The irq-pm.c saves all the IRQ registers, including the IRQ_EINT and
IRQ_EINT_GROUP registers as it was easier than adding three different
files. Also ensuring that all the registers are restored to the same
state as before suspend is considered to be the best thing to do.

Note, we do not suspend the VIC here, this is done by the VIC driver
itself.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Fix the following sparse warnings in arch/arm/plat-s3c64xx/irq.c

arch/arm/plat-s3c64xx/irq.c:210:23: warning: incorrect type in initializer (different address spaces)
arch/arm/plat-s3c64xx/irq.c:210:23:    expected void *reg_base
arch/arm/plat-s3c64xx/irq.c:210:23:    got void [noderef] <asn:2>*regs
arch/arm/plat-s3c64xx/irq.c:215:2: warning: incorrect type in argument 1 (different address spaces)
arch/arm/plat-s3c64xx/irq.c:215:2:    expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/plat-s3c64xx/irq.c:215:2:    got void *
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Some of the startup output can be reduced to
KERN_DEBUG from KERN_INFO as it is only really
useful when trying to debug kernel initialisation
problems.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add demux handling for the UART interrupts
generated by the VIC into their seperate IRQs
that the serial driver can register.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the physical to virtual memory mapping and the
necessary interrupt demuxing for the PWM timer blocks.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add and initialise the two VIC (PL192) found on
the S3C64XX series CPUs.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>