In case an iscsi portal group will be defined as t10_pi enabled,
all connections on top of it will support protected transactions.

T10-PI support may require extra reource allocation and maintenance by
the transport layer, so we don't want to apply them on non-t10_pi network
portals. This is a hook for the iscsi target layer to signal the transport
at connection establishment that this connection will carry protected
transactions.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This is not going to be supported soon - so drop it.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Some transports (iSCSI/iSER/SRP/FC) support hardware INSERT/STRIP
capabilities while other transports like loopback/vhost-scsi need
perform this is software.

This patch allows fabrics using SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC
to signal the early LUN scan handling case where PROTECT CDB bits
are set, but no fabric buffer has been provided.

For transports which use generic new command these buffers have yet
to be allocated.

Also this way, target may support protection information
against legacy initiators (writes are inserted and reads
are stripped).

(Only set prot_pto for loopback during early special case - nab)
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

No need to actually compute protection information when formatting
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

SBC-3 mandates the protection checks that must be
performed in the rdprotect/wrprotect field. Use them.
According to backstore device pi_attributes and
cdb rdprotect/wrprotect field.

(Fix incorrect se_cmd->prot_type -> TARGET_PROT_NORMAL
 comparision in transport_generic_new_cmd - nab)
(Fix missing break in sbc_set_prot_op_checks - DanC + Sagi)
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

In case protection information is involved, allocate
protection SG-list for transport.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Building target_core_alua.o triggers a GCC warning:
    drivers/target/target_core_alua.c: In function ‘target_alua_state_check’:
    drivers/target/target_core_alua.c:773:18: warning: ‘alua_ascq’ may be used uninitialized in this function [-Wmaybe-uninitialized]
       cmd->scsi_ascq = alua_ascq;
                      ^

This is a false positive. A little trial and error shows it is
apparently caused by core_alua_state_lba_dependent(). It must be hard
for GCC to track the branches of a switch statement, inside a
list_for_each_entry loop, inside a while loop.

But if we add a small (inline) helper function we can reorganize the
code a bit. That also allows to drop alua_ascq which, obviously, gets
rid of this warning.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

When copying between device and command protection scatters
we must take into account that device scatters might be offset
and we might copy outside scatter range. Thus for each cmd prot
scatter we must take the min between cmd prot scatter, dev prot
scatter, and whats left (and loop in case we havn't copied enough
from/to cmd prot scatter).

Example (single t_prot_sg of len 2048):
kernel: sbc_dif_copy_prot: se_cmd=ffff880380aaf970, left=2048, len=2048, dev_prot_sg_offset=3072, dev_prot_sg_len=4096
kernel: isert: se_cmd=ffff880380aaf970 PI error found type 0 at sector 0x2600 expected 0x0 vs actual 0x725f, lba=2580

Instead of copying 2048 from offset 3072 (copying junk outside sg
limit 4096), we must to copy 1024 and continue to next sg until
we complete cmd prot scatter.

This issue was found using iSER T10-PI offload over rd_mcp (wasn't
discovered with fileio since file_dev prot sglists are never offset).

Changes from v1:
- Fix sbc_copy_prot copy length miss-calculation

Changes from v0:
- Removed psg->offset consideration for psg_len computation
- Removed sg->offset consideration for offset condition
- Added copied consideraiton for len computation
- Added copied offset to paddr when doing memcpy
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch addresses a couple of different hug shutdown issues
related to wait_event() + isert_conn->state.  First, it changes
isert_conn->conn_wait + isert_conn->conn_wait_comp_err from
waitqueues to completions, and sets ISER_CONN_TERMINATING from
within isert_disconnect_work().

Second, it splits isert_free_conn() into isert_wait_conn() that
is called earlier in iscsit_close_connection() to ensure that
all outstanding commands have completed before continuing.

Finally, it breaks isert_cq_comp_err() into seperate TX / RX
related code, and adds logic in isert_cq_rx_comp_err() to wait
for outstanding commands to complete before setting ISER_CONN_DOWN
and calling complete(&isert_conn->conn_wait_comp_err).
Acked-by: NSagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

There are a handful of uses of list_empty() for cmd->i_conn_node
within iser-target code that expect to return false once a cmd
has been removed from the per connect list.

This patch changes all uses of list_del -> list_del_init in order
to ensure that list_empty() returns false as expected.
Acked-by: NSagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch fixes a bug in iscsit_get_tpg_from_np() where the
tpg->tpg_state sanity check was looking for TPG_STATE_FREE,
instead of != TPG_STATE_ACTIVE.

The latter is expected during a normal TPG shutdown once the
tpg_state goes into TPG_STATE_INACTIVE in order to reject any
new incoming login attempts.

Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Because then this sg is passed to sbc_copy_prot which will
hit a protection fault in cases we have more than a single sg.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch adds the three missing DIF related sense codes within
transport_generic_request_failure(), which are required to ensure
that the correct ASC/ASQC is generated by the subsequent call to
transport_send_check_condition_and_sense().

Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch fixes a bug in sbc_dif_copy_prot() where the updated addr
offset did not take into account the case where the associated
scatterlist had not been incremented.

This addresses the case where incoming protection scatterlists may
contain a length smaller than PAGE_SIZE across multiple entires,
when the target protection scatterlists are always being explicitly
filled up to PAGE_SIZE before adding another entry.

Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Need to take into account that protection sg_list
(copy-buffer) may consist of multiple entries.

Changes from v0:
- Changed commit description
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The CMD_T_FAILED flag is set used in one place to record the result of a
trivial test, and it is only tested once, few lines later.  We might as
well make the code simpler and easier to read by directly doing the test
of "success" where we want to use it.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch fixes Status SNACK handling of BegRun=0 to allow
for all unacknowledged respones to be resent, instead of
always assuming that BegRun would be an explicit value less
than the current ExpStatSN.
Reported-by: Nsantosh kulkarni <santosh.kulkarni@calsoftinc.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Commit fbfe858f ("target_core_spc: Include target device
descriptor in VPD page 83") added a new length variable, but (due to a
cut and paste mistake?) just checks scsi_name_len against 256 twice.
Fix this to check scsi_target_len for overflow too.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch changes core_alua_state_lba_dependent() to use do_div()
instead sector_div() to avoid the following link error on 32-bit
with CONFIG_LBDAF=n as reported by Jim:

buildlog-1391099072.txt-drivers/built-in.o: In function `target_alua_state_check':
buildlog-1391099072.txt-(.text+0x928d93): undefined reference to `__umoddi3'
buildlog-1391099072.txt:make: *** [vmlinux] Error 1 --
buildlog-1391101753.txt-  CC      init/version.o
buildlog-1391101753.txt-  LD      init/built-in.o
buildlog-1391101753.txt-drivers/built-in.o: In function `core_alua_state_lba_dependent':
buildlog-1391101753.txt-/home/jim/linux/drivers/target/target_core_alua.c:503: undefined reference to `__umoddi3'
buildlog-1391101753.txt:make: *** [vmlinux] Error 1
Reported-by: NJim Davis <jim.epost@gmail.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch addresses a >= v3.11 free-after-use regression
in core_scsi3_emulate_pro_register() that was introduced
in the following commit:

commit bc118fe4
Author: Andy Grover <agrover@redhat.com>
Date:   Thu May 16 10:41:04 2013 -0700

    target: Further refactoring of core_scsi3_emulate_pro_register()

To avoid the free-after-use, save an type value before hand, and
only call core_scsi3_put_pr_reg() with a valid *pr_reg.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org> #3.11+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch fixes a percpu_ref_put race for se_lun->lun_ref in
transport_lun_remove_cmd() where ->lun_ref could end up being
put more than once per command via different target completion
and fabric release contexts.

It adds a cmpxchg() for se_cmd->lun_ref_active to ensure that
percpu_ref_put() is only ever called once per se_cmd.

This bug was manifesting itself as a LUN shutdown regression
bug in >= v3.13 code, where percpu_ref_kill() would end up
hanging indefinately due to the incorrect percpu_ref count.

(Change se_cmd->lun_ref_active from bool -> int to force at
 least a 4-byte cmpxchg with MIPS ll/sc ins. - Fengguang)
Reported-by: NTommy Apel <tommyapeldk@gmail.com>
Cc: Tommy Apel <tommyapeldk@gmail.com>
Cc: <stable@vger.kernel.org> #3.13+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

When creating network portals rapidly, such as when restoring a
configuration, LIO's code to reuse existing portals can return a false
negative if the thread hasn't run yet and set np_thread_state to
ISCSI_NP_THREAD_ACTIVE. This causes an error in the network stack
when attempting to bind to the same address/port.

This patch sets NP_THREAD_ACTIVE before the np is placed on g_np_list,
so even if the thread hasn't run yet, iscsit_get_np will return the
existing np.

Also, convert np_lock -> np_mutex + hold across adding new net portal
to g_np_list to prevent a race where two threads may attempt to create
the same network portal, resulting in one of them failing.

(nab: Add missing mutex_unlocks in iscsit_add_np failure paths)
(DanC: Fix incorrect spin_unlock -> spin_unlock_bh)
Signed-off-by: NAndy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org> #3.1+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

SPC-4 states that data-integrity errors shall also report
the failed sector in CHECK_CONDITION response sense data
information field.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch propigates the use of task state bitmask now used by
percpu_ida_alloc() up the iscsi-target callchain, replacing the
use of GFP_ATOMIC for TASK_RUNNING, and GFP_KERNEL for
TASK_INTERRUPTIBLE.

Also, drop the unnecessary gfp_t parameter to isert_allocate_cmd(),
and just pass TASK_INTERRUPTIBLE into iscsit_allocate_cmd().
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch addresses a bug where connection reset would hang
indefinately once percpu_ida_alloc() was starved for tags, due
to the fact that it always assumed uninterruptible sleep mode.

So now make percpu_ida_alloc() check for signal_pending_state() for
making interruptible sleep optional, and convert iscsit_allocate_cmd()
to set TASK_INTERRUPTIBLE for GFP_KERNEL, or TASK_RUNNING for
GFP_ATOMIC.
Reported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch changes percpu_ida_alloc() + callers to accept task state
bitmask for prepare_to_wait() for code like target/iscsi that needs
it for interruptible sleep, that is provided in a subsequent patch.

It now expects TASK_UNINTERRUPTIBLE when the caller is able to sleep
waiting for a new tag, or TASK_RUNNING when the caller cannot sleep,
and is forced to return a negative value when no tags are available.

v2 changes:
  - Include blk-mq + tcm_fc + vhost/scsi + target/iscsi changes
  - Drop signal_pending_state() call
v3 changes:
  - Only call prepare_to_wait() + finish_wait() when != TASK_RUNNING
    (PeterZ)
Reported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NKent Overstreet <kmo@daterainc.com>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch addresses an traditional iscsi-target fabric ack starvation
issue where iscsit_allocate_cmd() -> percpu_ida_alloc_state() ends up
hitting slow path percpu-ida code, because iscsit_ack_from_expstatsn()
is expected to free ack'ed tags after tag allocation.

This is done to take into account the tags waiting to be acknowledged
and released in iscsit_ack_from_expstatsn(), but who's number are not
directly limited by the CmdSN Window queue_depth being enforced by
the target.

So that said, this patch bumps up the pre-allocated number of
per session tags to:

  (max(queue_depth, ISCSIT_MIN_TAGS) * 2) + ISCSIT_EXTRA_TAGS

for good measure to avoid the percpu_ida_alloc_state() slow path.

Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch updates tcm_loop_driver_probe() to set protection
information using scsi_host_set_prot() and scsi_host_set_guard(),
which currently enabled all modes of DIF/DIX protection, minus
DIX TYPE0.

Also, update tcm_loop_submission_work() to pass struct scsi_cmnd
related protection into target_submit_cmd_map_sgls() during CDB
dispatch.
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch adds support for DIF protection into rd_execute_rw() code
for WRITE/READ I/O using sbc_dif_verify_[write,read]() logic.

It also adds rd_get_prot_table() for locating protection SGLs
assoicated with the ramdisk backend device.

v2 changes:
  - Make rd_execute_rw() to u32 sectors count instead of sector_t
  - Drop SCF_PROT usage

Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch adds rd_build_prot_space() + rd_release_prot_space() logic
to setup + release protection information scatterlists.

It also adds rd_init_prot() + rd_free_prot() se_subsystem_api
callbacks used by target core code for setup + release of
protection information.

v2 changes:
  - Drop unused sg_table from rd_release_prot_space (Wei)
  - Drop rd_release_prot_space call from rd_free_device

Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch refactors rd_build_device_space() + rd_release_device_space()
into rd_allocate_sgl_table() + rd_release_device_space() so that they
may be used seperatly for setup + release of protection information
scatterlists.

Also add explicit memset of pages within rd_allocate_sgl_table() based
upon passed 'init_payload' value.

v2 changes:
  - Drop unused sg_table from rd_release_device_space (Wei)

Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch adds support for DIF protection into fd_execute_rw() code
for WRITE/READ I/O using sbc_dif_verify_[write,read]() logic.

It adds fd_do_prot_rw() for handling interface with FILEIO PI, and
uses a locally allocated fd_prot->prot_buf + fd_prot->prot_sg for
interacting with SBC DIF verify emulation code.

Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch adds support for DIF protection init/format support into
the FILEIO backend.

It involves using a seperate $FILE.protection for storing PI that is
opened via fd_init_prot() using the common pi_prot_type attribute.
The actual formatting of the protection is done via fd_format_prot()
using the common pi_prot_format attribute, that will populate the
initial PI data based upon the currently configured pi_prot_type.

Based on original FILEIO code from Sagi.

v1 changes:
  - Fix sparse warnings in fd_init_format_buf (Fengguang)

Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch adds blk_integrity passthrough support for block_device
backends using IBLOCK.

This includes iblock_alloc_bip() + setup of bio_integrity_payload
information that attaches to the leading struct bio once bio_list
is populated during fast-path iblock_execute_rw() I/O dispatch.

It also updates setup in iblock_configure_device() to detect modes
of protection + se dev->dev_attrib.pi_prot_type accordingly, along
with creating required bio_set integrity mempools.

Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch adds support to target_submit_cmd_map_sgls() for
accepting 'sgl_prot' + 'sgl_prot_count' parameters for
DIF protection information.

Note the passed parameters are stored at se_cmd->t_prot_sg
and se_cmd->t_prot_nents respectively.

Also, update tcm_loop and vhost-scsi fabrics usage of
target_submit_cmd_map_sgls() to take into account the
new parameters.

Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch adds support for exposing DIF protection device
attributes via configfs.  This includes:

   pi_prot_type: Protection Type (0, 1, 3 currently support)
   pi_prot_format: Protection Format Operation (FILEIO only)

Within se_dev_set_pi_prot_type() it also adds the se_subsystem_api
device callbacks to setup per device protection information.

v2 changes:
  - Drop pi_guard_type + pi_prot_version related code (MKP)
  - Add pi_prot_format logic (Sagi)
  - Add ->free_prot callback in target_free_device
  - Add hw_pi_prot_type read-only attribute

Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch updates spc_modesense_control() to set the Application
Tag Owner (ATO) bit when when DIF emulation is enabled by the
backend device.
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch updates sbc_emulate_readcapacity_16() to set
P_TYPE and PROT_EN bits when DIF emulation is enabled by
the backend device.
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch updates spc_emulate_evpd_86() (extended INQUIRY) to
report GRD_CHK (Guard Check) and REF_CHK (Reference Check) bits
when DIF emulation is enabled by the backend device.
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch updates spc_emulate_inquiry_std() to set the
PROTECT bit when DIF emulation is enabled by the backend
device.
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>