Use the clock framework to get the rate of the peripheral clock.
Remove the now obsolete get_uart_baud_base function.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7468/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch introduces common clock framework integration for all
configurable on-chip clocks on Alchemy chips:

- 2 or 3 PLLs which generate integer multiples of the root rate 12MHz,
- 6 dividers which take one of the 3 PLLs as input and divide their
  rate by either multiples of 2 or 1 (Au1300).
- another bank of up to 6 muxes which take either one of the 6
  above dividers or one of the PLLs directly and divide their rate
  further by 1, 2, 3 or 4.
- a few other sources which are used by onchip peripherals and are
  informational.

This implementation will take the clock tree as it was set up
by boot firmware: all in-kernel boards should continue to work
without having to set up the clock tree in board code.

CLK_IGNORE_DISABLED will be removed once all drivers have been
converted.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7466/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

replace au_read/write/sync with __raw_read/write and wmb.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7465/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch changes the static memory controller registers to offsets
from base, prefixes them with AU1000_ to avoid silent failures due to
changed addresses and introduces helpers to access them.

No functional changes, comparing assembly of a few select functions shows
no differences.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7463/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch changes all absolute SYS_XY registers to offsets from the
SYS block base, prefixes them with AU1000 to avoid silent failures due
to changed addresses, and introduces helper functions to read/write
them.

No functional changes, comparing assembly of a few select functions shows
no differences.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7464/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Move the C-code after all macros:  A follow-on patch which
introduces helpers to access the SYS_* registers needs this to build.

Just code shuffling, no functional changes.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7461/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Move the register offsets and bit descriptions from the au1000.h header
to their only user, the au1000_eth.c driver.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: netdev@vger.kernel.org
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7460/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove the unused SSI I2S and AC97C register definitions.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7462/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NDaniel Walter <dwalter@google.com>
Reviewed-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7150/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Kconfig doesn't select CRC32 so it's possible to build a Lasat kernel
without CONFIG_CRC32 resulting in a build error:

  LD      vmlinux
arch/mips/built-in.o: In function `lasat_init_board_info':
(.text+0x22c): undefined reference to `crc32_le'
arch/mips/built-in.o: In function `lasat_write_eeprom_info':
(.text+0x7fc): undefined reference to `crc32_le'
make: *** [vmlinux] Error 1
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Previously, the lower limit for the MIPS SC initialization loop was
set incorrectly allowing one extra loop leading to writes
beyond the MSC ioremap'd space. More precisely, the value of the 'imp'
in the last loop increased beyond the msc_irqmap_t boundaries and
as a result of which, the 'n' variable was loaded with an incorrect
value. This value was used later on to calculate the offset in the
MSC01_IC_SUP which led to random crashes like the following one:

CPU 0 Unable to handle kernel paging request at virtual address e75c0200,
epc == 8058dba4, ra == 8058db90
[...]
Call Trace:
[<8058dba4>] init_msc_irqs+0x104/0x154
[<8058b5bc>] arch_init_irq+0xd8/0x154
[<805897b0>] start_kernel+0x220/0x36c

Kernel panic - not syncing: Attempted to kill the idle task!

This patch fixes the problem
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Reviewed-by: NJames Hogan <james.hogan@imgtec.com>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7118/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When allocating stack space for BPF memwords we need to use the
appropriate 32 or 64-bit instruction to avoid losing the top 32 bits
of the stack pointer.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7135/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When loading a pointer to register we need to use the appropriate
32 or 64bit instruction to preserve the pointers' top 32bits.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7180/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The skb->pkt_type field is defined as follows:

u8 pkt_type:3,
   fclone:2,
   ipvs_property:1,
   peeked:1,
   nf_trace:1

resulting to the following layout in big-endian systems

[pkt_type][fclone][ipvs_propery][peeked][nf_trace]
^                                                ^
|                                                |
LSB                                             MSB

As a result, the existing code did not work because it was trying to
match pkt_type == 7 whereas in reality it is 7<<5 on big-endian
systems.

This has been fixed in the interpreter in
0dcceabb
"net: filter: fix SKF_AD_PKTTYPE extension on big-endian"

The fix is to look for 7<<5 on big-endian systems for the pkt_type
field, and shift by 5 so the packet type will be at the lower 3 bits
of the A register.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7132/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove BUG_ON() if the shift immediate is >=32 to avoid kernel crashes
due to malicious user input. If the shift immediate is >= 32,
we simply load the destination register with 0 since only
32-bit instructions are used by JIT so this will do the
correct thing even on MIPS64.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7179/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Previously, update_on_xread() only set the reset flag if SEEN_X hasn't
been set already. However, SEEN_X is used to indicate that X is used
as destination or source register so there are some cases where X
is only used as source register and we really need to make sure that it
has been initialized in time. As a result of which, drop this function and
always set X to zero if it's used in any of the opcodes.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7133/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

is_range() was meant to check whether the number is within
the s16 range or not. However the return values and consumers expected
the exact opposite. We fix that by inverting the logic in the function
to return 'true' for < s16 and 'false' for > s16.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Reported-by: NAlexei Starovoitov <ast@plumgrid.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7131/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

We should prevent spamming the logs during normal execution of bpf-jit.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Suggested-by: NAlexei Starovoitov <ast@plumgrid.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7129/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

If VLAN_TAG_PRESENT is not zero, then return 1 as expected by
classic BPF. Otherwise return 0.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7128/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Using VLAN_VID_MASK is not correct to get the vlan tag. Use
~VLAN_PRESENT_MASK instead and make sure it's u16 so the top 16-bits
will be removed. This will ensure that the emit_andi() code will not
treat this as a big 32-bit unsigned value.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7127/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The sltiu and sltu instructions will set the scratch register
to 1 if A <= X|K so fix the emitted branch conditional to check
for scratch != zero rather than scratch >= zero which would complicate
the resuling branch logic given that MIPS does not have a BGT or BGET
instructions to compare general purpose registers directly.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7126/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The SKF_AD_PKTTYPE uses the skb pointer so make sure it's in the
flags so it will be initialized in time.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7125/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The VLAN_VID_MASK and VLAN_TAG_PRESENT are immediates, so using
'and' which expects 3 registers will produce wrong results. Fix
this by using the 'andi' instruction.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7124/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Previously, the negative offset was not checked leading to failures
due to trying to load data beyond the skb struct boundaries. Until we
have proper asm helpers in place, it's best if we return ENOSUPP if K
is negative when trying to JIT the filter or 0 during runtime if we
do an indirect load where the value of X is unknown during build time.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7123/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Reading from the HI register to get the division result is wrong.
The quotient is placed in the LO register.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7122/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Commit d6b3314b "MIPS: uasm: Add lh uam
instruction" added the 'lh' micro-assembler instruction but it used the
'lw' opcode for it. Fix it by using the correct 'lh' opcode.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7121/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/7120/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It will be used later on by the SLT instruction.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7119/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

  mips: allmodconfig fails in 3.16-rc1 with lots of undefined symbols.

  arch/mips/net/bpf_jit.c: In function 'is_load_to_a':
  arch/mips/net/bpf_jit.c:559:7: error: 'BPF_S_LD_W_LEN' undeclared (first use in this function)
  arch/mips/net/bpf_jit.c:559:7: note: each undeclared identifier is reported only once for each function it appears in
  arch/mips/net/bpf_jit.c:560:7: error: 'BPF_S_LD_W_ABS' undeclared (first use in this function)
  [...]

The reason behind this is that 34805931 ("net: filter: get rid of
BPF_S_* enum") was routed via net-next tree, that takes all BPF-related
changes, at a time where MIPS BPF JIT was not part of net-next, while
c6610de3 ("MIPS: net: Add BPF JIT") was routed via mips arch tree
and went into mainline within the same merge window. Thus, fix it up by
converting BPF_S_* in a similar fashion as in 34805931 for MIPS.
Reported-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org>
Cc: Linux MIPS Mailing List <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7099/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This reverts commit eec43a22 "MIPS: Save/restore MSA context around
signals" and the MSA parts of ca750649 "MIPS: kernel: signal:
Prevent save/restore FPU context in user memory" (the restore path of
which appears incorrect anyway...).

The reverted patch took care not to break compatibility with userland
users of struct sigcontext, but inadvertantly changed the offset of the
uc_sigmask field of struct ucontext. Thus Linux v3.15 breaks the
userland ABI. The MSA context will need to be saved via some other
opt-in mechanism, but for now revert the change to reduce the fallout.

This will have minimal impact upon use of MSA since the only supported
CPU which includes it (the P5600) is 32-bit and therefore requires that
the experimental CONFIG_MIPS_O32_FP64_SUPPORT Kconfig option be selected
before the kernel will set FR=1 for a task, a requirement for MSA use.
Thus the users of MSA are limited to known small groups of people & this
patch won't be breaking any previously working MSA-using userland
outside of experimental settings.

[ralf@linux-mips.org: Fixed rejects.]

Cc: stable@vger.kernel.org
Reported-by: NJoseph S. Myers <joseph@codesourcery.com>
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7107/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The fix in the preceeding commit did do exactly the same thing in two
places showing some code cleanup was due.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

kvm_arch_vcpu_free() is called in 2 code paths:

1) kvm_vm_ioctl()
       kvm_vm_ioctl_create_vcpu()
           kvm_arch_vcpu_destroy()
               kvm_arch_vcpu_free()
2) kvm_put_kvm()
       kvm_destroy_vm()
           kvm_arch_destroy_vm()
               kvm_mips_free_vcpus()
                   kvm_arch_vcpu_free()

Neither of the paths handles VCPU free. We need to do it in
kvm_arch_vcpu_free() corresponding to the memory allocation in
kvm_arch_vcpu_create().
Signed-off-by: NDeng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: stable@vger.kernel.org
Reviewed-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Older GCC doesn't get named initializations of anonymous structs right,
that is members are not initializable in the containing structure through
name however old style initializations are working fine.

The issue exists with gcc up to 4.5.x.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Commit 91bbefe6 "arch,mips: Convert smp_mb__*()" replaced the
smp_mb__* functions with a simpler API, whilst commit 3179d37e
"MIPS: pm-cps: add PM state entry code for CPS systems" introduced
new uses of smp_mb__before_atomic_inc & smp_mb__after_clear_bit.
Replace those calls with the corresponding before & after atomic
functions of the new, simpler API in order to avoid a build failure:

  arch/mips/kernel/pm-cps.c: In function 'coupled_barrier':
  arch/mips/kernel/pm-cps.c:104:2: error: 'smp_mb__before_atomic_inc' is
    deprecated (declared at include/linux/atomic.h:11)
    [-Werror=deprecated-declarations]

  arch/mips/kernel/pm-cps.c: In function 'cps_pm_enter_state':
  arch/mips/kernel/pm-cps.c:161:2: error: 'smp_mb__after_clear_bit' is
    deprecated (declared at include/linux/bitops.h:48)
    [-Werror=deprecated-declarations]
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Reviewed-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7086/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Commit 91bbefe6 "arch,mips: Convert smp_mb__*()" replaced the
smp_mb__after_atomic_dec function with smp_mb__after_atomic, whilst
commit 1d8f1f5a "MIPS: smp-cps: hotplug support" introduced a new
use of it. Replace that use with smp_mb__after_atomic in order to avoid
a build failure:

  arch/mips/kernel/smp-cps.c: In function 'cps_cpu_disable':
  arch/mips/kernel/smp-cps.c:304:2: error: 'smp_mb__after_atomic_dec' is
    deprecated (declared at include/linux/atomic.h:35)
    [-Werror=deprecated-declarations]
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Reviewed-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7085/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This adds an RTC platform device for DECstation systems so that they can
use the rtc-cmos driver for their RTC device.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

sys_sgetmask and sys_ssetmask are obsolete system calls no longer
supported in libc.

This patch replaces architecture related __ARCH_WANT_SYS_SGETMAX by expert
mode configuration.That option is enabled by default for those
architectures.
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently hugepage migration is available for all archs which support
pmd-level hugepage, but testing is done only for x86_64 and there're
bugs for other archs.  So to avoid breaking such archs, this patch
limits the availability strictly to x86_64 until developers of other
archs get interested in enabling this feature.

Simply disabling hugepage migration on non-x86_64 archs is not enough to
fix the reported problem where sys_move_pages() hits the BUG_ON() in
follow_page(FOLL_GET), so let's fix this by checking if hugepage
migration is supported in vma_migratable().
Signed-off-by: NNaoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reported-by: NMichael Ellerman <mpe@ellerman.id.au>
Tested-by: NMichael Ellerman <mpe@ellerman.id.au>
Acked-by: NHugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: <stable@vger.kernel.org>	[3.12+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- added interrupt support for GIO devices
- improved detection of GIO cards on Indigo2
- added more known GIO cards
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7055/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

In octeon_3xxx.dts file, there is a definiton for twsi/twsi2 interrupts.
But there is no code for initialization of this interrupts. This patch adds
code for initialization of twsi interrupts.
Signed-off-by: NEunbong Song <eunb.song@samsung.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6816/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>