Set bits 0, 4, 5 and 7 of PCI configuration register 0x40 in the
quirk.  This has the following effects and is recommended by the
vendor.

* Force enable of IDE channels (used to be left alone as BIOS
  configured)

* Change initial phase behavior of PIO cycle such that the host pulls
  down the bus instead of tristating it.  Vendor recommends this
  setting.

The above settings are better for the current generation of
controllers and needed for the upcoming next generation.

Tested on JMB363.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Ethan Hsiao <ethanhsiao@jmicron.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Another one doing spurious NCQ completions.  Blacklist it.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Did a complete audit of these and found we have another error case.

ata_bus_softreset calls ata_check_status which means that it tries to do
an ioread8 on the port blindly and check versus 0xFF for an error.

It should of course be using the ap->ops method for this via chk_status,
and this bug causes a wrog status call on the NS87415 at least.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Tackle the relatively sane complaints of checkpatch --file.

The vast majority is indentation and whitespace changes, the rest are

* #include fixes
* printk KERN_xxx prefix addition
* BSS/initializer cleanups
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

	Update ALB mode monitor to hold correct locks (RTNL and nothing
else) when calling dev_set_promiscuity.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

	Convert more lock acquisitions to _bh flavor to avoid deadlock
with workqueue activity and add acquisition of RTNL in appropriate places.
Affects ALB mode, as well as core bonding functions and sysfs.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

	Convert locking-related activity to new & improved system.
Convert some lock acquisitions to _bh and rework parts of ALB mode, both
to avoid deadlocks with workqueue activity.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

	Convert mii (link state) monitor to acquire correct locks for
failover events.  In particular, failovers generally require RTNL at a low
level (when manipulating device MAC addresses, for example) and no other
locks.  The high level monitor is responsible for acquiring a known set
of locks, RTNL, the bond->lock for read and the slave_lock for write, and
the low level failover processing can then release appropriate locks as
needed.  This patch provides the high level portion.

	As it is undesirable to acquire RTNL for every monitor pass (which
may occur as often as every 10 ms), the miimon has been converted to
do conditional locking.  A first pass inspects all slaves to determine
if any action is required, and if so, a second pass (after acquring RTNL)
is done to perform any actions (doing a complete rescan, as the situation
may have changed when all locks were released).
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

	Change locking in balance-rr transmit processing to use a free
running counter to determine which slave to transmit on.  Instead, a
free-running counter is maintained, and modulo arithmetic used to select
a slave for transmit.

	This removes lock operations from the TX path, and eliminates
a deadlock introduced by the conversion to work queues.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

	Convert bonding timers to workqueues.  This converts the various
monitor functions to run in periodic work queues instead of timers.  This
patch introduces the framework and convers the calls, but does not resolve
various locking issues, and does not stand alone.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add missing &:

drivers/net/pasemi_mac.c: In function 'pasemi_mac_clean_rx':
drivers/net/pasemi_mac.c:553: warning: passing argument 1 of 'prefetch'
makes pointer from integer without a cast
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

 The dfx_bus_uninit() call is called from dfx_unregister() which is
__devexit and which is ultimately the ->remove call for the device.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix off-by one in remove logic that just got introduced.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Plus minor formatting fixes.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NMatteo Croce <technoboy85@gmail.com>
Signed-off-by: NEugene Konev <ejka@imfi.kspu.ru>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Driver for the watchdog timer. Still doesn't reboots the machine
on some boards, but we have improved and cleaned it
Signed-off-by: NMatteo Croce <technoboy85@gmail.com>
Signed-off-by: NNicolas Thill <nico@openwrt.org>
Signed-off-by: NEnrik Berkhan <Enrik.Berkhan@akk.org>
Signed-off-by: NChrister Weinigel <wingel@nano-system.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

ICP's Wafer 5823 SBC has, as far as I can tell, the same WDT as many,
if not all ICP's SBC's (that do have a WDT). I have tested it with
several boards, including Rocky 4783, Rocky 3703 and Rocky 3782. 

I propose a rename of the  Wafer 5823 watchdog timer driver
to something like "IPC (SBC) Watchdog Timer", to reflect that it
works with other IPC boards (maybe even all of them).
Signed-off-by: NVeljkovic Srdjan <sveljko@gvs.co.yu>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The original serial-number calculations based on WWPN no longer
apply to newer ISPs (ISP24xx and ISP25xx).  These newer board's
serial number reside in the VPD.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

For recent ISPs, software during CS_UNDERRUN handling must
determine if the two residuals, firmware-calculated and FCP_RSP,
are different to recognize if a frame has been dropped.  Update
the driver to catch this condition, and clear the
SS_RESIDUAL_UNDER and lscsi_status bits.  This logic is
consistent with what earlier firmwares did by explicitly
cracking open the FCP_RSP statuses and clearing
SS_RESIDUAL_UNDER.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Recent ISPs need only the single MMIO BAR to manipulate HW
registers.  Unfortunately, ISP21xx, ISP22xx, ISP23xx, and ISP63xx
type cards still require the I/O mapped region to manipulate the
FLASH via the two HW flash-registers (flash_address and
flash_data).
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

[SCSI] qla2xxx: Fix issue where final flash-segment updates were falling into the slow-path write handler.

Original implementation would not use the burst-write mechanisms
for requests equal to OPTROM_BURST_DWORDS transfer dwords.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Since both NVRAM and VPD regions of the flash reside on unaligned
sector boundaries, during update, the driver must perform a
read-modify-write operation to the composite NVRAM/VPD region.
This affects ISP25xx type boards only.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

As the intermixing may cause issues where HCCR bits could be
cleared inappropriately during MSI/MSI-X interrupt handling.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Commit b9f2c044 replaced mv643xx_get_stats_count() with
mv643xx_get_sset_count(), but forgot to hook it up.

drivers/net/mv643xx_eth.c:2678: warning: mv643xx_get_sset_count defined but not used
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>

This function just printed a message to the user; move the print to its
only caller, and turn it into an starget_printk.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This structure is accessed by the device; the fewer Linux things in it,
the better.  Using the pci_dev pointer from the hostdata requires a lot
of changes:

 - Pass Scsi_Host to a lot of routines which currently take a sym_hcb.
 - Set the Scsi_Host as the pci drvdata (instead of the sym_hcb)
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Make sym_interrupt return an irqreturn_t instead of void, and take a
Scsi_Host instead of a sym_hcb.  Pass the Scsi_Host to the interrupt
handler instead of the sym_hcb.  Rename the host_data to sym_data.
Keep a pci_dev pointer in the sym_data.  Rename the Scsi_Host from
instance to shost.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

These macros aren't needed any more.  They used to be used for SPARC.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

If we have a scsi_cmnd, it gives the user more information than the
sym_name, and maybe the target.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

By introducing the use_dac(), set_dac() and DMA_DAC_MASK macros, we can
eliminate a lot of ifdefs from the code.  We now rely on the compiler to
optimise away a few things that we'd formerly relied on the preprocessor
to do.  This makes sym_setup_bus_dma_mask() small enough to inline into
its only caller.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

With sysfs making these options tunable at runtime, there's no
justification for keeping this horrendously complex specification
string around.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

These struct elements record info that is never needed
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Following the same path as ->revision_id, remove ->device_id
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Auke missed the sym2 driver in his initial sweep.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This patch adds the PCI error recovery callbacks to the Symbios SCSI device
driver.  It includes support for First Failure Data Capture.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>

Assorted changes to initial patches, including returning IRQ_NONE from the
interrupt handler if the device is offline and re-using the eh_done completion
in the scsi error handler.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Instead of telling the reset routine that the command completed from
sym_eh_done, do it from sym_xpt_done.  The 'to_do' element of the ucmd
is redundant -- it serves only to tell whether eh_done is valid or not,
and we can tell this by checking to see if it's NULL.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Interrupts can't be re-entered, so it's sufficient to call spin_lock, not
spin_lock_irqsave().
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The midlayer won't scan the host ID, so we don't need to check.
This is the only caller of sym_xpt_done2, so remove that too.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>