The firmware spec states that the timeout for all commands should be 60 seconds.

In the past, the spec indicated that there were several classes of timeout
(short, medium, and long).  The driver has these different timeout classes.
We leave the class differentiation in the driver as-is (to protect against any
future spec changes), but set the timeout for all classes to be 60 seconds.

In addition, we fix a few commands which had hard-coded numeric timeouts specified.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Structs allocated for the resource tracker must be freed in
the error flow.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The reserved lKey is different for each VF.
A base lkey value is returned in QUERY_DEV_CAP at offset 0x98.

The reserved L_key value for a VF is:
    VF_lkey = base_lkey + (VF_number << 8).

This VF L_key value should be returned in QUERY_FUNC_CAP
(opcode-modifier = 0) at offset 0x48.

To indicate that the lkey value at offset 0x48 is valid, the Hypervisor
sets a flag bit in dword 0x0, offset 27 in the QUERY_FUNC_CAP wrapper
function.

When the VF calls QUERY_FUNC_CAP, it should check if this flag bit is set.
If it is set, the VF should take the reserved lkey value at offset 0x48.
If the bit is not set, the VF should not use a reserved lkey
(i.e., should set its reserved lkey value to 0).
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the firmware can detect a bad cable, allow it to generate an
event, and print the problem in the log.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previous commit is based on a wrong assumption, fdb messages are always sent
into the netns where the interface stands (see vxlan_fdb_notify()).

These fdb messages doesn't embed the rtnl attribute IFLA_LINK_NETNSID, thus we
need to add it (useful to interpret NDA_IFINDEX or NDA_DST for example).

Note also that vxlan_nlmsg_size() was not updated.

Fixes: 193523bf ("vxlan: advertise netns of vxlan dev in fdb msg")
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jonathan Toppins says:

====================
bonding: various 802.3ad fixes

This patch series is a forward porting of patches we (Cumulus) are shipping
in our 3.2 series kernels. These fixes attempt to make 802.3ad bonding mode
more predictable in certian state machine transtions in addition to fixing
802.3ad bond carrier determination when bonding min_links option is changed.
Specific notes are contained within each patch.

For this patch series there are no userspace facing changes, a diff between
the modinfo output showed no difference. However, there are behavioral
facing changes, primarily in the bond carrier state. Please make sure to
review carefully.

v2:
 * fixed some style issues
 * dropped a portion of patch 1 in favor of more testing on my side
====================
Signed-off-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix sparse warning about non-static function

drivers/net/bonding/bond_main.c:3737:5: warning: symbol
'bond_3ad_xor_xmit' was not declared. Should it be static?
Reviewed-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NJonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a slave is added to a bond and it is not in full duplex mode,
AD_PORT_LACP_ENABLED flag is cleared, due to this LACP PDU is not sent
on slave. When the duplex is changed to full, the flag needs to be set
to send LACP PDU.

Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NSatish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: NJonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch attempts to fix the following problems when an actor or
partner's aggregator is not active:
    1. a slave's lacp port state is marked as AD_STATE_SYNCHRONIZATION
       even if it is attached to an inactive aggregator. LACP advertises
       this state to the partner, making the partner think he can move
       into COLLECTING_DISTRIBUTING state even though this link will not
       pass traffic on the local side

    2. a slave goes into COLLECTING_DISTRIBUTING state without checking
       if the aggregator is actually active

    3. when in COLLECTING_DISTRIBUTING state, the partner parameters may
       change, e.g. the partner_oper_port_state.SYNCHRONIZATION. The
       local mux machine is not reacting to the change and continue to
       keep the slave and bond up

    4. When bond slave leaves an inactive aggregator and joins an active
       aggregator, the actor oper port state need to update to SYNC state.

v2:
 * fix style issues in bond_3ad.c

Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NWilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: NJonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mode 802.3ad, fix incorrect bond slave active state when slave is not in
active aggregator. During bond_open(), the bonding driver always sets
the slave active flag to true if the bond is not in active-backup, alb,
or tlb modes. Bonding should let the aggregator selection logic set the
active flag when in 802.3ad mode.

Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NWilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: NJonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: NJonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

return type of wait_for_completion_timeout is unsigned long not int, this
patch just fixes up the declarations.
Signed-off-by: NNicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NNicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	arch/arm/boot/dts/imx6sx-sdb.dts
	net/sched/cls_bpf.c

Two simple sets of overlapping changes.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Don't OOPS on socket AIO, from Christoph Hellwig.

 2) Scheduled scans should be aborted upon RFKILL, from Emmanuel
    Grumbach.

 3) Fix sleep in atomic context in kvaser_usb, from Ahmed S Darwish.

 4) Fix RCU locking across copy_to_user() in bpf code, from Alexei
    Starovoitov.

 5) Lots of crash, memory leak, short TX packet et al bug fixes in
    sh_eth from Ben Hutchings.

 6) Fix memory corruption in SCTP wrt.  INIT collitions, from Daniel
    Borkmann.

 7) Fix return value logic for poll handlers in netxen, enic, and bnx2x.
    From Eric Dumazet and Govindarajulu Varadarajan.

 8) Header length calculation fix in mac80211 from Fred Chou.

 9) mv643xx_eth doesn't handle highmem correctly in non-TSO code paths.
    From Ezequiel Garcia.

10) udp_diag has bogus logic in it's hash chain skipping, copy same fix
    tcp diag used.  From Herbert Xu.

11) amd-xgbe programs wrong rx flow control register, from Thomas
    Lendacky.

12) Fix race leading to use after free in ping receive path, from Subash
    Abhinov Kasiviswanathan.

13) Cache redirect routes otherwise we can get a heavy backlog of rcu
    jobs liberating DST_NOCACHE entries.  From Hannes Frederic Sowa.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (48 commits)
  net: don't OOPS on socket aio
  stmmac: prevent probe drivers to crash kernel
  bnx2x: fix napi poll return value for repoll
  ipv6: replacing a rt6_info needs to purge possible propagated rt6_infos too
  sh_eth: Fix DMA-API usage for RX buffers
  sh_eth: Check for DMA mapping errors on transmit
  sh_eth: Ensure DMA engines are stopped before freeing buffers
  sh_eth: Remove RX overflow log messages
  ping: Fix race in free in receive path
  udp_diag: Fix socket skipping within chain
  can: kvaser_usb: Fix state handling upon BUS_ERROR events
  can: kvaser_usb: Retry the first bulk transfer on -ETIMEDOUT
  can: kvaser_usb: Send correct context to URB completion
  can: kvaser_usb: Do not sleep in atomic context
  ipv4: try to cache dst_entries which would cause a redirect
  samples: bpf: relax test_maps check
  bpf: rcu lock must not be held when calling copy_to_user()
  net: sctp: fix slab corruption from use after free on INIT collisions
  net: mv643xx_eth: Fix highmem support in non-TSO egress path
  sh_eth: Fix serialisation of interrupt disable with interrupt & NAPI handlers
  ...

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the case when alloc_netdev fails we return NULL to a caller. But there is no
check for NULL in the probe drivers. This patch changes NULL to an error
pointer. The function description is amended to reflect what we may get
returned.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull powerpc fixes from Michael Ellerman:
 "Two powerpc fixes"

* tag 'powerpc-3.19-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
  powerpc/powernv: Restore LPCR with LPCR_PECE1 cleared
  powerpc/xmon: Fix another endiannes issue in RTAS call from xmon

Pull one more module fix from Rusty Russell:
 "SCSI was using module_refcount() to figure out when the module was
  unloading: this broke with new atomic refcounting.  The code is still
  suspicious, but this solves the WARN_ON()"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
  scsi: always increment reference count

The socket already carries the net namespace with it so there is
no need to be passing another net around.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the commit d75b1ade ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget. When in busy_poll is we return 0
in napi_poll. We should return budget.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
ipsec 2015-01-26

Just two small fixes for _decode_session6() where we
might decode to wrong header information in some rare
situations.

Please pull or let me know if there are problems.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible to see the old value of the LP advertising flags
through ethtool after reconfiguring the PHY and before autonegotiation
completes.  If autonegotiation is turned off then the last value seen
will persist indefinitely.
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

David L Stevens says:

====================
sunvnet: fix null pointer deref and crash recovery

These patches fix an incorrect ordering in releasing ring data, clear pending
tx buffers on a reset, and make the sunvnet driver more reliable when remote
systems crash during active transmits.
====================
Acked-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a remote machine crashes while there are pending transmit buffers, the
sunvnet driver reallocates the ring descriptors giving us enries that have
state VIO_DESC_FREE but also an allocated skb. This results in a BUG_ON()
call when the remote reboots and we reach that point in the ring.

This patch:

1) clears pending tx packets in the ring on port reset
2) changes a BUG_ON() to a pr_warn() when a remote host has given us an invalid
	descriptor state
3) collapses multiple active buffer frees in a ring to a single message per
	ring and adds the device name and remote MAC address

This fixes the particular problem of not cleaning up pending buffers on a
reset, but also prevents us from crashing if the remote handles descriptors
out of order or sets an unexpected state for a descriptor.
Signed-off-by: NDavid L Stevens <david.stevens@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the clearing of ring data in vnet_port_free_tx_bufs to after
 the freeing of pending buffers in the ring. Otherwise, this can result in
 dereferencing a NULL pointer.
Reported-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NDavid L Stevens <david.stevens@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lubomir Rintel reported that during replacing a route the interface
reference counter isn't correctly decremented.

To quote bug <https://bugzilla.kernel.org/show_bug.cgi?id=91941>:
| [root@rhel7-5 lkundrak]# sh -x lal
| + ip link add dev0 type dummy
| + ip link set dev0 up
| + ip link add dev1 type dummy
| + ip link set dev1 up
| + ip addr add 2001:db8:8086::2/64 dev dev0
| + ip route add 2001:db8:8086::/48 dev dev0 proto static metric 20
| + ip route add 2001:db8:8088::/48 dev dev1 proto static metric 10
| + ip route replace 2001:db8:8086::/48 dev dev1 proto static metric 20
| + ip link del dev0 type dummy
| Message from syslogd@rhel7-5 at Jan 23 10:54:41 ...
|  kernel:unregister_netdevice: waiting for dev0 to become free. Usage count = 2
|
| Message from syslogd@rhel7-5 at Jan 23 10:54:51 ...
|  kernel:unregister_netdevice: waiting for dev0 to become free. Usage count = 2

During replacement of a rt6_info we must walk all parent nodes and check
if the to be replaced rt6_info got propagated. If so, replace it with
an alive one.

Fixes: 4a287eba ("IPv6 routing, NLM_F_* flag support: REPLACE and EXCL flags support, warn about missing CREATE flag")
Reported-by: NLubomir Rintel <lkundrak@v3.sk>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Tested-by: NLubomir Rintel <lkundrak@v3.sk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
Fixes for sh_eth #3

I'm continuing review and testing of Ethernet support on the R-Car H2
chip.  This series fixes the last of the more serious issues I've found.

These are not tested on any of the other supported chips.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Use the return value of dma_map_single(), rather than calling
  virt_to_page() separately
- Check for mapping failue
- Call dma_unmap_single() rather than dma_sync_single_for_cpu()
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dma_map_single() may fail if an IOMMU or swiotlb is in use, so
we need to check for this.
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we try to clear EDRRR and EDTRR and immediately continue to
free buffers.  This is unsafe because:

- In general, register writes are not serialised with DMA, so we still
  have to wait for DMA to complete somehow
- The R8A7790 (R-Car H2) manual states that the TX running flag cannot
  be cleared by writing to EDTRR
- The same manual states that clearing the RX running flag only stops
  RX DMA at the next packet boundary

I applied this patch to the driver to detect DMA writes to freed
buffers:

> --- a/drivers/net/ethernet/renesas/sh_eth.c
> +++ b/drivers/net/ethernet/renesas/sh_eth.c
> @@ -1098,7 +1098,14 @@ static void sh_eth_ring_free(struct net_device *ndev)
>  	/* Free Rx skb ringbuffer */
>  	if (mdp->rx_skbuff) {
>  		for (i = 0; i < mdp->num_rx_ring; i++)
> +			memcpy(mdp->rx_skbuff[i]->data,
> +			       "Hello, world", 12);
> +		msleep(100);
> +		for (i = 0; i < mdp->num_rx_ring; i++) {
> +			WARN_ON(memcmp(mdp->rx_skbuff[i]->data,
> +				       "Hello, world", 12));
>  			dev_kfree_skb(mdp->rx_skbuff[i]);
> +		}
>  	}
>  	kfree(mdp->rx_skbuff);
>  	mdp->rx_skbuff = NULL;

then ran the loop:

    while ethtool -G eth0 rx 128 ; ethtool -G eth0 rx 64; do echo -n .; done

and 'ping -f' toward the sh_eth port from another machine.  The
warning fired several times a minute.

To fix these issues:

- Deactivate all TX descriptors rather than writing to EDTRR
- As there seems to be no way of telling when RX DMA is stopped,
  perform a soft reset to ensure that both DMA enginess are stopped
- To reduce the possibility of the reset truncating a transmitted
  frame, disable egress and wait a reasonable time to reach a
  packet boundary before resetting
- Update statistics before resetting

(The 'reasonable time' does not allow for CS/CD in half-duplex
mode, but half-duplex no longer seems reasonable!)
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If RX traffic is overflowing the FIFO or DMA ring, logging every time
this happens just makes things worse.  These errors are visible in the
statistics anyway.
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: phy: prevent double suspend

This patch series addresses a problem that Fugang and I observed on different
platforms where a given PHY device might end-up being suspended twice.

Once as part of the call from ndo_open() all the way down to phy_detach() and
phy_suspend() and a second time when the generic platform device/driver
suspend/resume callbacks are called in drivers/net/phy/mdio_bus.c.

Thanks to Fugang for giving this a quick try on i.MX6/FEC and reporting
positive test results!
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As part of a call to ndo_close() a netdevice driver may call
phy_disconnect() -> phy_detach() -> phy_suspend(), such that the PHY is
suspsended at this point and a netdevice driver may clock gate the
backing peripheral providing MDIO bus accessses as well.

Update mdio_bus_phy_may_suspend() to return whether a PHY is allowed to
be suspended and conversely resumed if and only if it was not previously
suspended before while it is currently in detached (netdev pointer is
NULL) state.

This fixes bus errors seen during S2/S3 suspend/resume cycles for
netdevice drivers such as GENET which clock gates the entire Ethernet
MAC, including the MDIO bus block.
Acked-by: NFugang Duan <B38611@freescale.com>
Tested-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to avoid double calls to phydev->drv->suspend and resume, keep
track of whether the PHY has already been suspended as a consequence of
a successful call to phy_suspend(). We will use this in our MDIO bus
suspend/resume hooks to avoid a double suspend call.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

has_fixups was introduced to help keeping track of fixups/quirks running
on a PHY device, but we did not update the comment above struct
phy_device accordingly.

Fixes: b0ae009f (net: phy: add "has_fixups" boolean property")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

phy_suspend and phy_resume are an abstraction on top of the PHY device
driver suspend and resume callbacks, utilize those since they are the
proper interface to suspending and resuming a PHY device.
Acked-by: NFugang Duan <B38611@freescale.com>
Tested-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hariprasad Shenai says:

====================
Add support to dump cim ibq, obq and qinfo, etc

This patch series adds support to dump cim_ibq, cim_obq, sge_qinfo, pm_stats
and clk debugfs entries.

The patches series is created against 'net-next' tree.
And includes patches on cxgb4 driver.

We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>