This further reorganizes the init code flow to match that of the
8192eu vendor driver. This helps diffing the register write log
against that of the vendor driver.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In order to debug 8192eu support, reorder some init code to match the
flow of the vendor driver.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

after factoring out mwifiex_cancel_pending_scan_cmd
the function is not called outside of cmdevt file
moved function to head of file to avoid forward declaration,
also moved mwifiex_recycle_cmd_node since they are very similar
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Releasing the scan_pending lock in mwifiex_check_next_scan_command
introduces a short window where pending scan commands can be removed
or added before removing them all in mwifiex_cancel_pending_scan_cmd.
I think this is safe, since the worst thing to happen is that a
pending scan cmd is removed by the command handler. Adding new scan
commands is not possible while one is pending, see scan_processing flag.
Since all commands are removed from the queue anyway, we don't care if
some commands are removed by a different code path earlier, the final
state remains the same.
I assume, that the critical section needed for the check has been
extended over clearing the pending scan queue out of convenience. The
lock was already held and releasing it and grab it again was just
more work. It doesn't seem to be necessary because of concurrency.
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

improves readability
Reviewed-by: NJulian Calaby <julian.calaby@gmail.com>
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

merge copy/paste code
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

"x ? x : y" can be simplified as "x ? : y"
https://gcc.gnu.org/onlinedocs/gcc/Conditionals.html#ConditionalsReviewed-by: NJulian Calaby <julian.calaby@gmail.com>
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

given this structure:
struct foo {
  struct bar {
     int baz;
  }
}

these accesses are equivalent:
(*(foo->bar)).baz
foo->bar->baz
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

During system suspend, there is a kernel WARNING issued if there
is a pending command present. By marking the wait queue disabled
after calling the command completion routine fixes it.
Signed-off-by: NVishal Thanki <vishalthanki@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

IEEE80211_CHAN_NO_HT40PLUS and IEEE80211_CHAN_NO_HT40PLUS channel
flags tell if HT40 operation is allowed on a channel or not.

This patch ensures ht_capability information is modified
accordingly so that we don't end up creating a HT40 connection
when it's not allowed for current regulatory domain.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Host hang is observed if card is removed before firmware download
gets completed. In this case, firmware will be failed to download and
adapter structure gets freed.

In other thread, mwifiex_remove_card() waits on semaphore until the
firmware download fails. This wait is not necessary and may result in
invalid adapter access.

This patch uses down_trylock to return immediately so that hang issue
won't occur.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds default setting for pcie firmware download name in
case that there are newer chipset version.
Signed-off-by: NShengzhen Li <szli@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for downloading usb/uart firmware for
8997 chipset by reading the chip version.
Signed-off-by: NShengzhen Li <szli@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds missing break statement at the end of
PCIE_DEVICE_ID_MARVELL_88W8897 switch section.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In receive path brcmf_proto_hdrpull() needs to be called and handled
similar in brcmf_rx_frame() and brcmf_rx_event(). Move that duplicated
code in separate function.
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Move event handling out of brcmf_netif_rx() avoiding the need
to pass a flag. This flag is only ever true for USB hosts as
other interface use separate brcmf_rx_event() function.
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The code for ampdu-rx host reorder is related to the firmware signalling
supported in BCDC protocol. This change moves the code to fwsignal module.
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Firmware uses asynchronized events as a communication method to the
host. The event packets are marked as ETH_P_LINK_CTL protocol type. For
SDIO and PCIe bus, this kind of packets are delivered through virtual
event channel not data channel. This patch adds a screening logic to
make sure the event handler only processes the events coming from the
correct channel.
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When p2p connection setup is performed without having ever done an
escan a null pointer exception can occur. This is because the ifp
to abort scanning is taken from escan struct while it was never
initialized. Fix this by using the primary ifp for scan abort. The
abort should still be performed and all scan related commands are
performed on primary ifp.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: NHante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Some nvram files/stores come without the boardrev information,
but firmware requires this to be set. When not found in nvram then
add a default boardrev string to the nvram data.
Reported-by: NRafal Milecki <zajec5@gmail.com>
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <franky.lin@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: NHante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Newer firmwares require the usage of the wowl wakeind struct as size
for the iovar to clear the wake indicators. Older firmwares do not
care, so change the used size.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: NHante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When the event_msgs iovar is set an array is used to configure the
enabled events. This arrays needs to nulled before configuring
otherwise unhandled events will be enabled. This solves a problem
where in case of wowl the host got woken by an incorrectly enabled
event.
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Adjust AFE before enabling PLL on 8192eu, probably also needed for
8723bu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

8192eu has it's own IQK calibration procedure, and notably uses
undocumented RF register 0x56 in the process.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Fixup another case where the hard coded register value was used
instead of the name.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Set REG_QUEUE_CTRL and REG_ACLK_MON for 8192eu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Implement workaround for LDPC RX hands on 8192eu. This was inspired by
workaround found in the 8192eu vendor driver.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The vendor driver set register 0xfe58 REG_USB_HWPWM in it's init
sequence for 8192eu. Do the same here.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Set HIMR[01] on 8192eu instead of HISR/HIMR. It's not obvious this
really matters for USB devices, but this matches the register writes
performed by the vendor driver.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Set REG_AFE_XTAL_CTRL on 8192eu to the vendor driver value, and do not
skip setting REG_MAX_AGGR_NUM on 8192eu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu requires clearing/restoring bit 17 in REG_FPGA0_POWER_SAVE
before/after writing RF registers.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu does not use REG_AFE_PLL_CTRL in it's BB init sequence, so
provide device specific handling.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu efuse only has power data for path A and B. It follows the
same layout as 8723bu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Pick PHY init table based on device before distinguishing between
1T/2T/high PA tables. The latter is only currently used for
8188cu/8192cu/8188ru.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu also requires it's own PHY init table.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

A device specific AGC table is required for the 8192eu as well.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add the required radio init tables for 8192eu devices.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu also has it's own TRXFF boundary value to set.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

To match the vendor driver, do not mess with AFE_XTAL_CTRL on 8192eu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>