This patch enabled the tlb flush range support in generic mmu layer.

Most of arch has self tlb flush range support, like ARM/IA64 etc.
X86 arch has no this support in hardware yet. But another instruction
'invlpg' can implement this function in some degree. So, enable this
feather in generic layer for x86 now. and maybe useful for other archs
in further.

Generic mmu_gather struct is protected by micro
HAVE_GENERIC_MMU_GATHER. Other archs that has flush range supported
own self mmu_gather struct. So, now this change is safe for them.

In future we may unify this struct and related functions on multiple
archs.

Thanks for Peter Zijlstra time and time reminder for multiple
architecture code safe!
Signed-off-by: NAlex Shi <alex.shi@intel.com>
Link: http://lkml.kernel.org/r/1340845344-27557-7-git-send-email-alex.shi@intel.comSigned-off-by: NH. Peter Anvin <hpa@zytor.com>

Testing show different CPU type(micro architectures and NUMA mode) has
different balance points between the TLB flush all and multiple invlpg.
And there also has cases the tlb flush change has no any help.

This patch give a interface to let x86 vendor developers have a chance
to set different shift for different CPU type.

like some machine in my hands, balance points is 16 entries on
Romely-EP; while it is at 8 entries on Bloomfield NHM-EP; and is 256 on
IVB mobile CPU. but on model 15 core2 Xeon using invlpg has nothing
help.

For untested machine, do a conservative optimization, same as NHM CPU.
Signed-off-by: NAlex Shi <alex.shi@intel.com>
Link: http://lkml.kernel.org/r/1340845344-27557-5-git-send-email-alex.shi@intel.comSigned-off-by: NH. Peter Anvin <hpa@zytor.com>

x86 has no flush_tlb_range support in instruction level. Currently the
flush_tlb_range just implemented by flushing all page table. That is not
the best solution for all scenarios. In fact, if we just use 'invlpg' to
flush few lines from TLB, we can get the performance gain from later
remain TLB lines accessing.

But the 'invlpg' instruction costs much of time. Its execution time can
compete with cr3 rewriting, and even a bit more on SNB CPU.

So, on a 512 4KB TLB entries CPU, the balance points is at:
	(512 - X) * 100ns(assumed TLB refill cost) =
		X(TLB flush entries) * 100ns(assumed invlpg cost)

Here, X is 256, that is 1/2 of 512 entries.

But with the mysterious CPU pre-fetcher and page miss handler Unit, the
assumed TLB refill cost is far lower then 100ns in sequential access. And
2 HT siblings in one core makes the memory access more faster if they are
accessing the same memory. So, in the patch, I just do the change when
the target entries is less than 1/16 of whole active tlb entries.
Actually, I have no data support for the percentage '1/16', so any
suggestions are welcomed.

As to hugetlb, guess due to smaller page table, and smaller active TLB
entries, I didn't see benefit via my benchmark, so no optimizing now.

My micro benchmark show in ideal scenarios, the performance improves 70
percent in reading. And in worst scenario, the reading/writing
performance is similar with unpatched 3.4-rc4 kernel.

Here is the reading data on my 2P * 4cores *HT NHM EP machine, with THP
'always':

multi thread testing, '-t' paramter is thread number:
	       	        with patch   unpatched 3.4-rc4
./mprotect -t 1           14ns		24ns
./mprotect -t 2           13ns		22ns
./mprotect -t 4           12ns		19ns
./mprotect -t 8           14ns		16ns
./mprotect -t 16          28ns		26ns
./mprotect -t 32          54ns		51ns
./mprotect -t 128         200ns		199ns

Single process with sequencial flushing and memory accessing:

		       	with patch   unpatched 3.4-rc4
./mprotect		    7ns			11ns
./mprotect -p 4096  -l 8 -n 10240
			    21ns		21ns

[ hpa: http://lkml.kernel.org/r/1B4B44D9196EFF41AE41FDA404FC0A100BFF94@SHSMSX101.ccr.corp.intel.com
  has additional performance numbers. ]
Signed-off-by: NAlex Shi <alex.shi@intel.com>
Link: http://lkml.kernel.org/r/1340845344-27557-3-git-send-email-alex.shi@intel.comSigned-off-by: NH. Peter Anvin <hpa@zytor.com>

Commit 026cee00 "params:
<level>_initcall-like kernel parameters" set old-style module
parameters to level 0.  And we call those level 0 calls where we used
to, early in start_kernel().

We also loop through the initcall levels and call the levelled
module_params before the corresponding initcall.  Unfortunately level
0 is early_init(), so we call the standard module_param calls twice.

(Turns out most things don't care, but at least ubi.mtd does).

Change the level to -1 for standard module_param calls.
Reported-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org

Zero is written at clear_tid_address when the process exits.  This
functionality is used by pthread_join().

We already have sys_set_tid_address() to change this address for the
current task but there is no way to obtain it from user space.

Without the ability to find this address and dump it we can't restore
pthread'ed apps which call pthread_join() once they have been restored.

This patch introduces the PR_GET_TID_ADDRESS prctl option which allows
the current process to obtain own clear_tid_address.

This feature is available iif CONFIG_CHECKPOINT_RESTORE is set.

[akpm@linux-foundation.org: fix prctl numbering]
Signed-off-by: NAndrew Vagin <avagin@openvz.org>
Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org>
Cc: Pedro Alves <palves@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A fix for commit b32dfe37 ("c/r: prctl: add ability to set new
mm_struct::exe_file").

After removing mm->num_exe_file_vmas kernel keeps mm->exe_file until
final mmput(), it never becomes NULL while task is alive.

We can check for other mapped files in mm instead of checking
mm->num_exe_file_vmas, and mark mm with flag MMF_EXE_FILE_CHANGED in
order to forbid second changing of mm->exe_file.
Signed-off-by: NKonstantin Khlebnikov <khlebnikov@openvz.org>
Reviewed-by: NCyrill Gorcunov <gorcunov@openvz.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Stack depth of 255 seems excessive, given that copy_from_user_nmi()
could be slow.
Signed-off-by: NArun Sharma <asharma@fb.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1334961696-19580-3-git-send-email-asharma@fb.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Weird topologies can lead to asymmetric domain setups. This needs
further consideration since these setups are typically non-minimal
too.

For now, make it work by adding an extra mask selecting which CPUs
are allowed to iterate up.

The topology that triggered it is the one from David Rientjes:

	10 20 20 30
	20 10 20 20
	20 20 10 20
	30 20 20 10

resulting in boxes that wouldn't even boot.
Reported-by: NDavid Rientjes <rientjes@google.com>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-3p86l9cuaqnxz7uxsojmz5rm@git.kernel.orgSigned-off-by: NIngo Molnar <mingo@kernel.org>

This patch fixes bug in macro radix_tree_for_each_contig().

If radix_tree_next_slot() sees NULL in next slot it returns NULL, but following
radix_tree_next_chunk() switches iterating into next chunk. As result iterating
becomes non-contiguous and breaks vfs "splice" and all its users.
Signed-off-by: NKonstantin Khlebnikov <khlebnikov@openvz.org>
Reported-and-bisected-by: NHans de Bruin <jmdebruin@xmsnet.nl>
Reported-and-bisected-by: NOndrej Zary <linux@rainbow-software.org>
Reported-bisected-and-tested-by: NToralf Förster <toralf.foerster@gmx.de>
Link: https://lkml.org/lkml/2012/6/5/64
Cc: stable <stable@vger.kernel.org> # 3.4.x
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

size type of drm_exynos_gem_mmap struct is changed to uint64_t and
it adds pad for the struct to be aligned as 64bit.
Signed-off-by: NInki Dae <inki.dae@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>

This is useful for SoCs whose I2C module's signals can be routed to
different sets of pins at run-time, using the pinctrl API.

                                 +-----+  +-----+
                                 | dev |  | dev |
    +------------------------+   +-----+  +-----+
    | SoC                    |      |        |
    |                   /----|------+--------+
    |   +---+   +------+     | child bus A, on first set of pins
    |   |I2C|---|Pinmux|     |
    |   +---+   +------+     | child bus B, on second set of pins
    |                   \----|------+--------+--------+
    |                        |      |        |        |
    +------------------------+  +-----+  +-----+  +-----+
                                | dev |  | dev |  | dev |
                                +-----+  +-----+  +-----+
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

introduced in Linux-3.5-rc1 by
66886d6f
(ACPI: Add stubs for (un)register_acpi_bus_type)

Fix header file warnings when CONFIG_ACPI is not enabled:

include/acpi/acpi_bus.h:443:42: warning: 'struct acpi_bus_type' declared inside parameter list
include/acpi/acpi_bus.h:443:42: warning: its scope is only this definition or declaration, which is probably not
include/acpi/acpi_bus.h:444:44: warning: 'struct acpi_bus_type' declared inside parameter list
Signed-off-by: NLen Brown <len.brown@intel.com>

This reverts commit 5ceb9ce6.

That commit seems to be the cause of the mm compation list corruption
issues that Dave Jones reported.  The locking (or rather, absense
there-of) is dubious, as is the use of the 'page' variable once it has
been found to be outside the pageblock range.

So revert it for now, we can re-visit this for 3.6.  If we even need to:
as Minchan Kim says, "The patch wasn't a bug fix and even test workload
was very theoretical".
Reported-and-tested-by: NDave Jones <davej@redhat.com>
Acked-by: NHugh Dickins <hughd@google.com>
Acked-by: NKOSAKI Motohiro <kosaki.motohiro@gmail.com>
Acked-by: NMinchan Kim <minchan@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The comment above it says "Stat data, not accessed from path walking",
but in fact some of inode fields we use for the common stat data was way
down at the end of the inode, causing unnecessary cache misses for the
common stat operations.

The inode structure is pretty big, and this can change padding depending
on field width, but at least on the common 64-bit configurations this
doesn't change the size.  Some of our inode layout has historically been
to tro to avoid unnecessary padding fields, but cache locality is at
least as important for layout, if not more.

Noticed by looking at kernel profiles, and noticing that the "i_blkbits"
access stood out like a sore thumb.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This reverts the tty layer change to use per-tty locking, because it's
not correct yet, and fixing it will require some more deep surgery.

The main revert is d29f3ef3 ("tty_lock: Localise the lock"), but
there are several smaller commits that built upon it, they also get
reverted here. The list of reverted commits is:

  fde86d31 - tty: add lockdep annotations
  8f6576ad - tty: fix ldisc lock inversion trace
  d3ca8b64 - pty: Fix lock inversion
  b1d679af - tty: drop the pty lock during hangup
  abcefe5f - tty/amiserial: Add missing argument for tty_unlock()
  fd11b42e - cris: fix missing tty arg in wait_event_interruptible_tty call
  d29f3ef3 - tty_lock: Localise the lock

The revert had a trivial conflict in the 68360serial.c staging driver
that got removed in the meantime.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When NetLabel is not enabled, e.g. CONFIG_NETLABEL=n, and the system
receives a CIPSO tagged packet it is dropped (cipso_v4_validate()
returns non-zero).  In most cases this is the correct and desired
behavior, however, in the case where we are simply forwarding the
traffic, e.g. acting as a network bridge, this becomes a problem.

This patch fixes the forwarding problem by providing the basic CIPSO
validation code directly in ip_options_compile() without the need for
the NetLabel or CIPSO code.  The new validation code can not perform
any of the CIPSO option label/value verification that
cipso_v4_validate() does, but it can verify the basic CIPSO option
format.

The behavior when NetLabel is enabled is unchanged.
Signed-off-by: NPaul Moore <pmoore@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Does block_sigmask() + tracehook_signal_handler();  called when
sigframe has been successfully built.  All architectures converted
to it; block_sigmask() itself is gone now (merged into this one).

I'm still not too happy with the signature, but that's a separate
story (IMO we need a structure that would contain signal number +
siginfo + k_sigaction, so that get_signal_to_deliver() would fill one,
signal_delivered(), handle_signal() and probably setup...frame() -
take one).
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Only 3 out of 63 do not.  Renamed the current variant to __set_current_blocked(),
added set_current_blocked() that will exclude unblockable signals, switched
open-coded instances to it.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

replace boilerplate "should we use ->saved_sigmask or ->blocked?"
with calls of obvious inlined helper...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

first fruits of ..._restore_sigmask() helpers: now we can take
boilerplate "signal didn't have a handler, clear RESTORE_SIGMASK
and restore the blocked mask from ->saved_mask" into a common
helper.  Open-coded instances switched...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

helpers parallel to set_restore_sigmask(), used in the next commits
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Everyone either defines it in arch thread_info.h or has TIF_RESTORE_SIGMASK
and picks default set_restore_sigmask() in linux/thread_info.h.  Kill the
ifdefs, slap #error in linux/thread_info.h to catch breakage when new ones
get merged.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

NFS optimizes away d_revalidates for last component of open.  This means that
open itself can find the dentry stale.

This patch allows the filesystem to return EOPENSTALE and the VFS will retry the
lookup on just the last component if possible.

If the lookup was done using RCU mode, including the last component, then this
is not possible since the parent dentry is lost.  In this case fall back to
non-RCU lookup.  Currently this is not used since NFS will always leave RCU
mode.
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Btrfs has to make sure we have space to allocate new blocks in order to modify
the inode, so updating time can fail.  We've gotten around this by having our
own file_update_time but this is kind of a pain, and Christoph has indicated he
would like to make xfs do something different with atime updates.  So introduce
->update_time, where we will deal with i_version an a/m/c time updates and
indicate which changes need to be made.  The normal version just does what it
has always done, updates the time and marks the inode dirty, and then
filesystems can choose to do something different.

I've gone through all of the users of file_update_time and made them check for
errors with the exception of the fault code since it's complicated and I wasn't
quite sure what to do there, also Jan is going to be pushing the file time
updates into page_mkwrite for those who have it so that should satisfy btrfs and
make it not a big deal to check the file_update_time() return code in the
generic fault path. Thanks,
Signed-off-by: NJosef Bacik <josef@redhat.com>

after all, 0 bytes and 0 pages is the same thing...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

When we do restore we would like to have a way to setup a former
mm_struct::exe_file so that /proc/pid/exe would point to the original
executable file a process had at checkpoint time.

For this the PR_SET_MM_EXE_FILE code is introduced.  This option takes a
file descriptor which will be set as a source for new /proc/$pid/exe
symlink.

Note it allows to change /proc/$pid/exe if there are no VM_EXECUTABLE
vmas present for current process, simply because this feature is a special
to C/R and mm::num_exe_file_vmas become meaningless after that.

To minimize the amount of transition the /proc/pid/exe symlink might have,
this feature is implemented in one-shot manner.  Thus once changed the
symlink can't be changed again.  This should help sysadmins to monitor the
symlinks over all process running in a system.

In particular one could make a snapshot of processes and ring alarm if
there unexpected changes of /proc/pid/exe's in a system.

Note -- this feature is available iif CONFIG_CHECKPOINT_RESTORE is set and
the caller must have CAP_SYS_RESOURCE capability granted, otherwise the
request to change symlink will be rejected.
Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org>
Reviewed-by: NOleg Nesterov <oleg@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

During checkpoint we dump whole process memory to a file and the dump
includes process stack memory.  But among stack data itself, the stack
carries additional parameters such as command line arguments, environment
data and auxiliary vector.

So when we do restore procedure and once we've restored stack data itself
we need to setup mm_struct::arg_start/end, env_start/end, so restored
process would be able to find command line arguments and environment data
it had at checkpoint time.  The same applies to auxiliary vector.

For this reason additional PR_SET_MM_(ARG_START | ARG_END | ENV_START |
ENV_END | AUXV) codes are introduced.
Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org>
Acked-by: NKees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Vagin <avagin@openvz.org>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

While doing the checkpoint-restore in the user space one need to determine
whether various kernel objects (like mm_struct-s of file_struct-s) are
shared between tasks and restore this state.

The 2nd step can be solved by using appropriate CLONE_ flags and the
unshare syscall, while there's currently no ways for solving the 1st one.

One of the ways for checking whether two tasks share e.g.  mm_struct is to
provide some mm_struct ID of a task to its proc file, but showing such
info considered to be not that good for security reasons.

Thus after some debates we end up in conclusion that using that named
'comparison' syscall might be the best candidate.  So here is it --
__NR_kcmp.

It takes up to 5 arguments - the pids of the two tasks (which
characteristics should be compared), the comparison type and (in case of
comparison of files) two file descriptors.

Lookups for pids are done in the caller's PID namespace only.

At moment only x86 is supported and tested.

[akpm@linux-foundation.org: fix up selftests, warnings]
[akpm@linux-foundation.org: include errno.h]
[akpm@linux-foundation.org: tweak comment text]
Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org>
Acked-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Andrey Vagin <avagin@openvz.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Valdis.Kletnieks@vt.edu
Cc: Michal Marek <mmarek@suse.cz>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A cleanup of rw_copy_check_uvector and compat_rw_copy_check_uvector after
changes made to support CMA in an earlier patch.

Rather than having an additional check_access parameter to these
functions, the first paramater type is overloaded to allow the caller to
specify CHECK_IOVEC_ONLY which means check that the contents of the iovec
are valid, but do not check the memory that they point to.  This is used
by process_vm_readv/writev where we need to validate that a iovec passed
to the syscall is valid but do not want to check the memory that it points
to at this point because it refers to an address space in another process.
Signed-off-by: NChris Yeoh <yeohc@au1.ibm.com>
Reviewed-by: NOleg Nesterov <oleg@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

eventfd_ctx->count is an __u64 counter which is allowed to reach
ULLONG_MAX.  eventfd_write() adds a __u64 value to "count", but the kernel
side eventfd_signal() only adds an int value to it.  Make them consistent.

[akpm@linux-foundation.org: update interface documentation]
Signed-off-by: NSha Zhengju <handai.szj@taobao.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Adds DMA Engine framework support into RapidIO subsystem.

Uses DMA Engine DMA_SLAVE interface to generate data transfers to/from
remote RapidIO target devices.

Introduces RapidIO-specific wrapper for prep_slave_sg() interface with an
extra parameter to pass target specific information.

Uses scatterlist to describe local data buffer.  Address flat data buffer
on a remote side.
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Acked-by: NVinod Koul <vinod.koul@linux.intel.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit b231cca4 ("message queues: increase range limits") changed
mqueue default value when attr parameter is specified NULL from hard
coded value to fs.mqueue.{msg,msgsize}_max sysctl value.

This made large side effect.  When user need to use two mqueue
applications 1) using !NULL attr parameter and it require big message
size and 2) using NULL attr parameter and only need small size message,
app (1) require to raise fs.mqueue.msgsize_max and app (2) consume large
memory size even though it doesn't need.

Doug Ledford propsed to switch back it to static hard coded value.
However it also has a compatibility problem.  Some applications might
started depend on the default value is tunable.

The solution is to separate default value from maximum value.
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>
Acked-by: NDoug Ledford <dledford@redhat.com>
Acked-by: NJoe Korty <joe.korty@ccur.com>
Cc: Amerigo Wang <amwang@redhat.com>
Acked-by: NSerge E. Hallyn <serue@us.ibm.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Mqueue limitation is slightly naieve parameter likes other ipcs because
unprivileged user can consume kernel memory by using ipcs.

Thus, too aggressive raise bring us security issue.  Example, current
setting allow evil unprivileged user use 256GB (= 256 * 1024 * 1024*1024)
and it's enough large to system will belome unresponsive.  Don't do that.

Instead, every admin should adjust the knobs for their own systems.
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: NDoug Ledford <dledford@redhat.com>
Acked-by: NJoe Korty <joe.korty@ccur.com>
Cc: Amerigo Wang <amwang@redhat.com>
Acked-by: NSerge E. Hallyn <serue@us.ibm.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit b231cca4 ("message queues: increase range limits") changed the
maximum size of a message in a message queue from INT_MAX to 8192*128.
Unfortunately, we had customers that relied on a size much larger than
8192*128 on their production systems.  After reviewing POSIX, we found
that it is silent on the maximum message size.  We did find a couple other
areas in which it was not silent.  Fix up the mqueue maximums so that the
customer's system can continue to work, and document both the POSIX and
real world requirements in ipc_namespace.h so that we don't have this
issue crop back up.

Also, commit 9cf18e1d ("ipc: HARD_MSGMAX should be higher not lower
on 64bit") fiddled with HARD_MSGMAX without realizing that the number was
intentionally in place to limit the msg queue depth to one that was small
enough to kmalloc an array of pointers (hence why we divided 128k by
sizeof(long)).  If we wish to meet POSIX requirements, we have no choice
but to change our allocation to a vmalloc instead (at least for the large
queue size case).  With that, it's possible to increase our allowed
maximum to the POSIX requirements (or more if we choose).

[sfr@canb.auug.org.au: using vmalloc requires including vmalloc.h]
Signed-off-by: NDoug Ledford <dledford@redhat.com>
Cc: Serge E. Hallyn <serue@us.ibm.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: Joe Korty <joe.korty@ccur.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Acked-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>