The IGEP v2 board is a low-cost, fan-less and industrial temperature
range single board computer that unleashes laptop-like performance and
expandability without the bulk, expense, or noise of typical desktop
machines. Its architecture shares much in common with other OMAP3 boards.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add CompuLab CM-T35 defconfig
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds basic support for CompuLab CM-T35 module.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

wl1251 is connected to the SPI bus in rx51, add support for this.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds board specific SDRAM init for RX51. This patch is a
collaboration of work from following people:

Juha Yrjola: Original code
Lauri Leukkunen: Port to RX51
Tero Kristo: Support for multiple OPP:s, merge of patches
Samu Onkalo: Fixed SDRAM parameters according to specs
Kalle Jokiniemi: A fix for rounding error
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Cc: Lauri Leukkunen <lauri.leukkunen@nokia.com>
Cc: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This adds a new defconfig for the HTC Herald series of devices.
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch introduces support for the HTC Herald (T-Mobile
Wing, etc.) series of smart phones -- board support and LCD
panel settings.
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Update DEBUG_LL for zoom2 board as CONFIG_OMAP_LL_DEBUG_NONE
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Create zoom3 defconfig file
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Zoom3 is the next version of Zoom2 board.
There has been a silicon update from zoom2 to zoom3.
        Zoom2 has OMAP34xx
        Zoom3 has OMAP3630 [1]
Zoom3 = OMAP3630 SOM board [2] + same zoom2 main board [3] + same debugboard

Zoom3 has a SDRAM part from Hynix
Zoom2 had SDRAM part from micron

Hynix memory timings are contributed by:
Chalhoub, Nicole and Bour, Vincent

Reuse the zoom2 files as much for zoom3, as at board level,
there is no change at all.

References: (courtesy Nishant Menon)
[1] OMAP3630
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12836&contentId=52606

[2] SOM boards
http://logicpd.com/products/system-modules/texas-instruments-omap35x-som-lv

[3] Zoom2 boards
http://logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp
OMAP3630:
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Cc: Nicole Chalhoub <n-chalhoub@ti.com>
Cc: Vincent Bour <v-bour@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The I2C-1 bus frequency on zoom2/zoom3/sdp3630 should be 2.4 MHz.
The speed is limited by TWL5030/GAIA; a higher speed could lead to errors
on the interface.

The maximum I2C speed depends on the system clock for GAIA:
2.2 MHz (sys-clk = 19.2 MHz)
2.4 MHz (sys-clk = 26 MHz)
2.9 MHz (sys-clk = 38.4 MHz)

For Zoom2/Zoom3/SDP3630 the system clock is 26Mhz
and hence choose 2.4Mhz for I2C1 bus speed
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Replace zoom2 with zoom name in board-zoom-peripherals.c file
and board-zoom-debugboard.c. Create mach/board-zoom.h.

This file has functions reused for boards: Zoom2/Zoom3/sdp3630.
Hence have all functions commonly named as zoom
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Split zoom2 board file into a base board file and a board-zoom-peripherals.c
file. That way the same peripherals file can be reused for zoom3 and sdp3630
in addition to zoom2.

Also remove unused struct omap_board_config_kernel entry.

NOTE: Keep the twl4030_madc_platform_data and twl4030_platform_data
entries in board-zoom2.c to avoid merge conflicts with the pending
patches in MFD tree. These entries will be removed later as a fix.

Following list shows the commonality across the three platforms and hence the
case for software reuse:

Peripheral    zoom2    zoom3  sdp3630
---------------------------------------
Ethernet        smsc    smsc    smc
NOR             n/a     n/a     B
Onenand         n/a     n/a     B
HDMI            A       A       B (present on different i2c)
NAND            A       A       A (same nand)
SDRAM           A       A       A (same sdram)
Keypad          A       A       A (same twl)
Camera          A       A       A (same sensor can be mounted)
LCD Display     A       A       A (same wvga display)
OPPs            A       A       A (same chip feature)
Audio           A       A       A (same audio via twl5030)
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Migrate to smsc911x ethernet driver instead of smc911x driver.
The smsc911x ethernet driver supports NAPI and performs better
under heavy traffic. With the smc911x driver we were witnessing
very high iowait time for high IO load over NFS.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Initialize vmmc and vmmc_aux regulators

Note that the omap3evm_twldata.vmmc1 and omap3evm_twldata.vsim
are set in omap3_evm_i2c_init() to avoid a merge conflict
with the MFD tree. These will be initialized in omap3evm_i2c_boardinfo
as a fix later on.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Added runtime programming for the differences in EHCI interface between
OMAP3EVM revisions (Rev >= E) and (Rev < E).

Changes:
	- EHCI PHY reset GPIO pin is 21 on Rev >= E while Rev < E
	  uses GPIO pin 135.
	- Rev >= E uses EHCI Vbus enable GPIO22 line.
	- Rev >= E uses GPIO61 to select EHCI port either on main board or
	  on Mistral Daughter Card (MDC). OMAP3EVM Rev < E doesn't have
	  EHCI port on main board.
	- Currently GPIO61 it programmed to enable EHCI port on main
	  board only.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>

Added function to differentiate between the OMAP3EVM revisions. The
chip-id of the ethernet PHY is being used for this purpose.

Rev A to D : 0x01150000
Rev >= E   : 0x92200000
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The mainline merge of the 3430SDP support (commit 6fdc29e2)
seems to have messed up the 3430 defconfig completely.

Update the defconfig using a known good version
(SDP defconfig from v2.6.26-omap2 and current beagle defconfig)
as reference.

The image size is now 1.9 MB down from 2.4 MB earlier, and
the number of modules is 8, down from 203. Build time also
scales proportionally.

Other support (OneNAND, etc) can be enabled as needed.

Note that this patch intentionally does not update CONFIG_FB
related options to avoid merge conflicts with the pending
omap_dss2 patches.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove the SYSFS_DEPRECATED flag from OMAP3 board defconfigs
This is a deprecated feature no longer needed.
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch disables a GPIO module when all pins of a GPIO
module are inactive (clock gating forced at module level) and
enables the module when any gpio in the module is requested.

The module is enabled only when "mod_usage" indicates that no GPIO
in that  module is currently active and the GPIO being requested
is the 1st one to be active in that module.

Each module would be disabled in omap_gpio_free() API when all
GPIOs in a particular module becomes inactive. The module is
re-enabled in omap_gpio_request() API when a GPIO is requested
from the module that was previously disabled.

Since individual GPIO's bookkeeping is added in this patch
via "mod_usage", the same is used in omap_set_gpio_debounce()
& omap_set_gpio_debounce_time() APIs to ensure that the gpio being
used is actually "requested" prior to being used (Nishant Menon's
<nm@ti.comSuggestion)

GPIO module level details are specific to hardware and hence
introducing this patch in low level layer (plat-omap/gpio.c)
Signed-off-by: NCharulatha V <charu@ti.com>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Cleanup the coding style in id.c while avoiding unneeded switch()
statements.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch uses a tasklet implementation for
sending mailbox messages.
Signed-off-by: NC A Subramaniam <subramaniam.ca@ti.com>
Signed-off-by: NRamesh Gupta G <grgupta@ti.com>
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Currently, this facilitates both the tesla and ducati
sides to request for the same irq through an
omap_mbox_get() call.
Signed-off-by: NC A Subramaniam <subramaniam.ca@ti.com>
Signed-off-by: NRamesh Gupta G <grgupta@ti.com>
Acked-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds code changes in the mailbox driver module to
add support for OMAP4 mailbox.
Signed-off-by: NHari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: NC A Subramaniam <subramaniam.ca@ti.com>
Signed-off-by: NRamesh Gupta G <grgupta@ti.com>
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Expose omap_mbox_enable()/disable_irq()
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>

Also removed from tx_data
Signed-off-by: NC A Subramaniam <subramaniam.ca@ti.com>
Acked-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

No need to handle it in isr, since irq won't happen during isr.
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

It's not used at present.
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Any protocol should be handled in the upper layer and mailbox driver
shouldn't care about the contents of messages.
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds resource information of mailbox driver for
OMAP4 mailbox module. Register base address also added
Signed-off-by: NC A Subramaniam <subramaniam.ca@ti.com>
Signed-off-by: NRamesh Gupta G <grgupta@ti.com>
Acked-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds changes to the build related files of mailbox
driver
Signed-off-by: NC A Subramaniam <subramaniam.ca@ti.com>
Signed-off-by: NRamesh Gupta G <grgupta@ti.com>
Acked-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

map_iovm_area is only called from a context where its second argument is
known not to be NULL, so drop the unnecessary test.  If new could be NULL,
the initialization of da should be moved below the test.

A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):

// <smpl>
@match exists@
expression x, E;
identifier fld;
@@

* x->fld
  ... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

All of the OMAP3 IVA physical address macros in
plat-omap/include/plat/omap34xx.h are wrong[1]:

OMAP34XX_IVA_INTC_BASE: The IVA interrupt controller does not appear
to be accessible from the L3 interconnect, and in any case is
definitely not at 0x40000000; the latter address appears to be the
internal IVA physical address base for the OMAP2420's interrupt control[2].

OMAP34XX_DSP_BASE: The section of L3 physical address space mapped to
the IVA starts at 0x5c000000, not 0x58000000.

OMAP34XX_DSP_MEM_BASE: It's not clear what this refers to, but it's not
in the L3 IVA address space.

OMAP34XX_DSP_IPI_BASE: The Intrusive Port Interface is a relic from
the OMAP2420 days and no longer applies to OMAP3.

OMAP34XX_DSP_MMU_BASE: The DSP MMU is mapped at 0x5d000000, not 0x5a000000.


Nothing that uses these can possibly be working, so drop them.  When
future code needs these, correct versions can be added in.

1. OMAP34xx Multimedia Device Silicon Revision 3.1.x Rev. W, Table 2-8:
   "L3 Interconnect View of the IVA2.2 Subsystem Memory Space."  p. 229.

2. OMAP2420 Multimedia Processor Silicon Revision 2.1.1, 2.2 (Rev. Q),
   section 2.2.4.1, "IVA Memory Space Seen by L3", p. 132.

3. ibid., section 4.3.11, "DSP IPI Overview", p. 200.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

When listing the various SoC features, print them on the same line.
So, instead of this

OMAP3430/3530 ES3.1
 - l2cache : Y
 - iva : Y
 - sgx : Y
 - neon : Y
 - isp : Y

you get this:

OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

omap3_check_revision() does not depend on omap3_check_features()
move this above so that we can add logic based on revision
detected in check_features.
Signed-off-by: NNishanth Menon <nm@ti.com>
Acked-by: NMika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

For ease of use it is preferrable to build in HSMMC driver
rather than build it as kernel module. This patches updates
default configuration for omap3evm to reflect this change.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for omap hsmmc2 8-bit mux configuration.
Signed-off-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The speed ctrl bit for MMC I/O is part of CONTROL_PROG_IO1 register
in omap3630.This patch sets it up accordingly.
Signed-off-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The HSMMC1 controller on omap3630 supprts only 4-bit mode. If cpu
is 3630 configure HSMMC1 wires to 4-bit.
Signed-off-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Change the cpu_is_omap3430() check to cpu_is_omap34xx() to allow HSMMC1/2
mux configuration for omap3630.
Signed-off-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>