As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

bnxt uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

bnx2x uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

mlx5 uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

mlx4 uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

i40evf uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

ice uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

igb uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

ixgb uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.

This also removes a problematic use of disable_irq() in
a context it is forbidden, as explained in commit
af3e0fcf ("8139too: Use disable_irq_nosync() in
rtl8139_poll_controller()")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
lasts for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

fm10k uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

ixgbevf uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

ixgbe uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Reported-by: NSong Liu <songliubraving@fb.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Tested-by: NSong Liu <songliubraving@fb.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We want to allow NAPI drivers to no longer provide
ndo_poll_controller() method, as it has been proven problematic.

team driver must not look at its presence, but instead call
netpoll_poll_dev() which factorize the needed actions.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Acked-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clang warns that the address of a pointer will always evaluated as true
in a boolean context:

drivers/net/ethernet/mellanox/mlx4/eq.c:243:11: warning: address of
array 'eq->affinity_mask' will always evaluate to 'true'
[-Wpointer-bool-conversion]
        if (!eq->affinity_mask || cpumask_empty(eq->affinity_mask))
            ~~~~~^~~~~~~~~~~~~
1 warning generated.

Use cpumask_available, introduced in commit f7e30f01 ("cpumask: Add
helper cpumask_available()"), which does the proper checking and avoids
this warning.

Link: https://github.com/ClangBuiltLinux/linux/issues/86Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of error, the function pci_create_slot() returns ERR_PTR() and
never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().

Fixes: a15f2c08 ("PCI: hv: support reporting serial number as slot information")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When extracting frames from the Ocelot switch, the frame check sequence
(FCS) is present at the end of the data extracted. The FCS was put into
the sk buffer which introduced some issues (as length related ones), as
the FCS shouldn't be part of an Rx sk buffer.

This patch fixes the Ocelot switch extraction behaviour by discarding
the FCS.

Fixes: a556c76a ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was reported that chip version 33 (RTL8168E) ends up with
10MBit/Half on a 1GBit link after resuming from S3 (with different
link partners). For whatever reason the PHY on this chip doesn't
properly start a renegotiation when soft-reset.
Explicitly requesting a renegotiation fixes this.

Fixes: a2965f12 ("r8169: remove rtl8169_set_speed_xmii")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reported-by: NNeil MacLeod <neil@nmacleod.com>
Tested-by: NNeil MacLeod <neil@nmacleod.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnxt offload code currently supports only 'push' and 'pop' operation: let
.ndo_setup_tc() return -EOPNOTSUPP if VLAN 'modify' action is configured.

Fixes: 2ae7408f ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: NDavide Caratti <dcaratti@redhat.com>
Acked-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MC-aware mode was introduced to mlxsw in commit 7b819530 ("mlxsw: spectrum:
Configure MC-aware mode on mlxsw ports") and fixed up later in commit
3a3539cd ("mlxsw: spectrum_buffers: Set up a dedicated pool for BUM
traffic"). As the final piece of puzzle, a firmware issue whereby a wrong
priority was assigned to BUM traffic was corrected in FW version 13.1703.4.
Therefore require this FW version in the driver.

Fixes: 7b819530 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support to configure the DORQ to use vlan-id/priority for
roce EDPM.

Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In certain multi-function switch dependent modes, firmware adds vlan tag 0
to the untagged frames. This leads to double tagging for the traffic
if the dcbx is enabled, which is not the desired behavior. To avoid this,
driver needs to set "dcb_dont_add_vlan0" flag.

Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In multi-function mode, driver receives the stag value (outer vlan)
for a PF from management FW (MFW). If the stag value is negotiated prior to
the driver load, then the stag is not notified to the driver and hence
driver will have the invalid stag value.
The fix is to request the MFW for STAG value during the driver load time.

Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With CONFIG_DMA_API_DEBUG enabled we now get a warning when using the
mvneta driver:

  mvneta d0030000.ethernet: DMA-API: device driver frees DMA memory with
  wrong function [device address=0x000000001165b000] [size=4096 bytes]
  [mapped as page] [unmapped as single]

This is because when using the s/w buffer management, the Rx descriptor
buffer is mapped with dma_map_page but unmapped with dma_unmap_single.
This patch fixes this by using the right unmapping function.

Fixes: 562e2f46 ("net: mvneta: Improve the buffer allocation method for SWBM")
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a network interface is created prior to the SFP socket being
available, ethtool can request module information.  This unfortunately
leads to an oops:

Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = (ptrval)
[00000008] *pgd=7c400831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1480 Comm: ethtool Not tainted 4.19.0-rc3 #138
Hardware name: Broadcom Northstar Plus SoC
PC is at sfp_get_module_info+0x8/0x10
LR is at dev_ethtool+0x218c/0x2afc

Fix this by not filling in the network device's SFP bus pointer until
SFP is fully bound, thereby avoiding the core calling into the SFP bus
code.

Fixes: ce0aa27f ("sfp: add sfp-bus to bridge between network devices and sfp cages")
Reported-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When no Tx IRQ is available, the txq_done() routine (called from
tx_done()) shouldn't be called from the polling function, as in such
case it is already called in the Tx path thanks to an hrtimer. This
mostly occurred when using PPv2.1, as the engine then do not have Tx
IRQs.

Fixes: edc660fa ("net: mvpp2: replace TX coalescing interrupts with hrtimer")
Reported-by: NStefan Chulski <stefanc@marvell.com>
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

EtherAVB hardware requires 0 to be written to status register bits in
order to clear them, however, care must be taken not to:

1. Clear other bits, by writing zero to them
2. Write one to reserved bits

This patch corrects the ravb driver with respect to the second point above.
This is done by defining reserved bit masks for the affected registers and,
after auditing the code, ensure all sites that may write a one to a
reserved bit use are suitably masked.
Signed-off-by: NKazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Reviewed-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following compile warning:

drivers/net/ethernet/broadcom/bnxt/bnxt_devlink.c:49:5: warning: ‘nvm_param.dir_type’ may be used uninitialized in this function [-Wmaybe-uninitialized]
  if (nvm_param.dir_type == BNXT_NVM_PORT_CFG)
Signed-off-by: Nzhong jiang <zhongjiang@huawei.com>
Acked-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the Netgear WNDAP620, the emac ethernet isn't receiving nor
xmitting any frames from/to the RTL8363SB (identifies itself
as a RTL8367RB).

This is caused by the emac hardware not knowing the forced link
parameters for speed, duplex, pause, etc.

This begs the question, how this was working on the original
driver code, when it was necessary to set the phy_address and
phy_map to 0xffffffff. But I guess without access to the old
PPC405/440/460 hardware, it's not possible to know.
Signed-off-by: NChristian Lamparter <chunkeey@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we are always setting the tail address of descriptor list to
the end of the pre-allocated list.

According to databook this is not correct. Tail address should point to
the last available descriptor + 1, which means we have to update the
tail address everytime we call the xmit function.

This should make no impact in older versions of MAC but in newer
versions there are some DMA features which allows the IP to fetch
descriptors in advance and in a non sequential order so its critical
that we set the tail address correctly.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Fixes: f748be53 ("stmmac: support new GMAC4")
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This follows David Miller advice and tries to fix coalesce timer in
multi-queue scenarios.

We are now using per-queue coalesce values and per-queue TX timer.

Coalesce timer default values was changed to 1ms and the coalesce frames
to 25.

Tested in B2B setup between XGMAC2 and GMAC5.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Fixes: 	ce736788 ("net: stmmac: adding multiple buffers for TX")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent firmware revisions have added the ability to force
these modems to USB2 mode, hiding their SuperSpeed
capabilities from the host.  The driver has been using the
SuperSpeed capability, as shown by the bcdUSB field of the
device descriptor, to detect the need to enable the DTR
quirk.  This method fails when the modems are forced to
USB2 mode by the modem firmware.

Fix by unconditionally enabling the DTR quirk for the
affected device IDs.
Reported-by: NFred Veldini <fred.veldini@gmail.com>
Reported-by: NDeshu Wen <dwen@sierrawireless.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Reported-by: NFred Veldini <fred.veldini@gmail.com>
Reported-by: NDeshu Wen <dwen@sierrawireless.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit d31fd43c ("clk: x86: Do not gate clocks enabled by the
firmware"), which added the code to mark clocks as CLK_IS_CRITICAL, causes
all unclaimed PMC clocks on Cherry Trail devices to be on all the time,
resulting on the device not being able to reach S0i3 when suspended.

The reason for this commit is that on some Bay Trail / Cherry Trail devices
the r8169 ethernet controller uses pmc_plt_clk_4. Now that the clk-pmc-atom
driver exports an "ether_clk" alias for pmc_plt_clk_4 and the r8169 driver
has been modified to get and enable this clock (if present) the marking of
the clocks as CLK_IS_CRITICAL is no longer necessary.

This commit removes the CLK_IS_CRITICAL marking, fixing Cherry Trail
devices not being able to reach S0i3 greatly decreasing their battery
drain when suspended.

Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861
Cc: Johannes Stezenbach <js@sig21.net>
Cc: Carlo Caione <carlo@endlessm.com>
Reported-by: NJohannes Stezenbach <js@sig21.net>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NStephen Boyd <sboyd@kernel.org>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some boards a platform clock is used as clock for the r8169 chip,
this commit adds support for getting and enabling this clock (assuming
it has an "ether_clk" alias set on it).

This is related to commit d31fd43c ("clk: x86: Do not gate clocks
enabled by the firmware") which is a previous attempt to fix this for some
x86 boards, but this causes all Cherry Trail SoC using boards to not reach
there lowest power states when suspending.

This commit (together with an atom-pmc-clk driver commit adding the alias)
fixes things properly by making the r8169 get the clock and enable it when
it needs it.

Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861
Cc: Johannes Stezenbach <js@sig21.net>
Cc: Carlo Caione <carlo@endlessm.com>
Reported-by: NJohannes Stezenbach <js@sig21.net>
Acked-by: NStephen Boyd <sboyd@kernel.org>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit d31fd43c ("clk: x86: Do not gate clocks enabled by the
firmware") causes all unclaimed PMC clocks on Cherry Trail devices to be on
all the time, resulting on the device not being able to reach S0i2 or S0i3
when suspended.

The reason for this commit is that on some Bay Trail / Cherry Trail devices
the ethernet controller uses pmc_plt_clk_4. This commit adds an "ether_clk"
alias, so that the relevant ethernet drivers can try to (optionally) use
this, without needing X86 specific code / hacks, thus fixing ethernet on
these devices without breaking S0i3 support.

This commit uses clkdev_hw_create() to create the alias, mirroring the code
for the already existing "mclk" alias for pmc_plt_clk_3.

Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861
Cc: Johannes Stezenbach <js@sig21.net>
Cc: Carlo Caione <carlo@endlessm.com>
Reported-by: NJohannes Stezenbach <js@sig21.net>
Acked-by: NStephen Boyd <sboyd@kernel.org>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Intel SoC was prevented from entering lower idle state because
of RTL8106E's ASPM was not enabled.

So enable ASPM on RTL8106E (chip version 39).
Now the Intel SoC can enter lower idle state, power consumption and
temperature are much lower.
Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>