If we fail to assign resources to a PCI BAR, this patch makes us try the
original address from BIOS rather than leaving it disabled.

Linux tries to make sure all PCI device BARs are inside the upstream
PCI host bridge or P2P bridge apertures, reassigning BARs if necessary.
Windows does similar reassignment.

Before this patch, if we could not move a BAR into an aperture, we left
the resource unassigned, i.e., at address zero.  Windows leaves such BARs
at the original BIOS addresses, and this patch makes Linux do the same.

This is a bit ugly because we disable the resource long before we try to
reassign it, so we have to keep track of the BIOS BAR address somewhere.
For lack of a better place, I put it in the struct pci_dev.

I think it would be cleaner to attempt the assignment immediately when the
claim fails, so we could easily remember the original address.  But we
currently claim motherboard resources in the middle, after attempting to
claim PCI resources and before assigning new PCI resources, and changing
that is a fairly big job.

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16263Reported-by: NAndrew <nitr0@seti.kr.ua>
Tested-by: NAndrew <nitr0@seti.kr.ua>
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The Report ID wasn't sent as part of the payload for reports which were sent
over the control endpoint. This is required by section 8.1 of the HID spec.
Signed-off-by: NAlan Ott <alan@signal11.us>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The UVC gadget driver borrowed code from the UVC host driver without
changing the symbol names. This results in a namespace clash with
multiple definitions of several symbols when compiling both drivers in
the kernel.

Make all generic UVC functions and variables static in the UVC gadget
driver, as the symbols are not referenced outside of the gadget driver.
Rename the uvc_trace_param global variable to uvc_gadget_trace_param.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Patch for linux-2.6.35-rc4 mainline kernel to enable Paul Qureshi's
Retro Adapter [http://keio.dk/retroadapter.html], an open source USB
device which allows controllers and joysticks from classic computers
and consoles to work on modern PCs, to appear as two separate devices
under Linux.
Signed-off-by: NPeter Edwards <samwise@bagshot-row.org>
Acked-by: NPaul Qureshi <retro@world3.net>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This USB flight yoke needs the NOGET quirk, like most of CH's other
products. This patch adds that.
Signed-off-by: NJonathan Rockway <jon@jrock.us>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

spi_t was removed in commit 644b2a68
("powerpc/cpm: Remove SPI defines and spi structs"), the commit assumed
that spi_t isn't used anywhere outside of the spi_mpc8xxx driver. But
it appears that the struct is needed for micropatch code. So, let's
reintroduce the struct.

Fixes the following build issue:

    CC      arch/powerpc/sysdev/micropatch.o
  micropatch.c: In function 'cpm_load_patch':
  micropatch.c:629: error: expected '=', ',', ';', 'asm' or '__attribute__' before '*' token
  micropatch.c:629: error: 'spp' undeclared (first use in this function)
  micropatch.c:629: error: (Each undeclared identifier is reported only once
  micropatch.c:629: error: for each function it appears in.)
Reported-by: NLEROY Christophe <christophe.leroy@c-s.fr>
Reported-by: NTony Breeds <tony@bakeyournoodle.com>
Cc: <stable@kernel.org> [ .33, .34 ]
Signed-off-by: NAnton Vorontsov <avorontsov@mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Sibyte i2c bus driver returns non-descriptive error values.
Update to return error values as defined in Documentation/i2c/fault-codes.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The new unified probing function differs from the original code, and
the preliminary test whether probing is possible must be updated
accordingly.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Fujitsu slightly changed the DMI strings in their recent machines,
(for example the D2778) and this breaks the automatic loading of the
needed fschmd driver. Being more tolerant on string comparison fixes
the issue.

This closes bug #15634:
https://bugzilla.kernel.org/show_bug.cgi?id=15634Signed-off-by: NJean Delvare <khali@linux-fr.org>
Tested-by: NSergey Spiridonov <sena@hurd.homeunix.org>
Cc: Hans de Goede <hdegoede@redhat.com>

Don't assume that CPU entry number and core ID always match. It
worked in the simple cases (single CPU, no HT) but fails on
multi-CPU systems.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NHuaxu Wan <huaxu.wan@intel.com>
Cc: stable@kernel.org

On hyper-threaded CPUs, each core appears twice in the CPU list. Skip
the second entry to avoid duplicate sensors.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NHuaxu Wan <huaxu.wan@intel.com>
Cc: stable@kernel.org

The IT8720F has no VIN7 pin, so VCCH should always be routed
internally to VIN7 with an internal divider. Curiously, there still
is a configuration bit to control this, which means it can be set
incorrectly. And even more curiously, many boards out there are
improperly configured, even though the IT8720F datasheet claims that
the internal routing of VCCH to VIN7 is the default setting. So we
force the internal routing in this case.

It turns out that all boards with the wrong setting are from Gigabyte,
so I suspect a BIOS bug. But it's easy enough to workaround in the
driver, so let's do it.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Jean-Marc Spaggiari <jean-marc@spaggiari.org>
Cc: stable@kernel.org

Reported temperature for ASB1 CPUs is too high.
Add ASB1 CPU revisions (these are also non-desktop variants) to the
list of CPUs for which the temperature fixup is not required.

Example: (from LENOVO ThinkPad Edge 13, 01972NG, system was idle)

  Current kernel reports

  $ sensors
  k8temp-pci-00c3
  Adapter: PCI adapter
  Core0 Temp:  +74.0 C
  Core0 Temp:  +70.0 C
  Core1 Temp:  +69.0 C
  Core1 Temp:  +70.0 C

  With this patch I have

  $ sensors
  k8temp-pci-00c3
  Adapter: PCI adapter
  Core0 Temp:  +54.0 C
  Core0 Temp:  +51.0 C
  Core1 Temp:  +48.0 C
  Core1 Temp:  +49.0 C

Cc: stable@kernel.org [.32.x .33.x, .34.x]
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Extract the microcode for the QLogic QLE7220 series IB HCA and use the
kernel microcode request facility to load the microcode.  This
supports Debian Linux's requirements to separate microcode which
doesn't have open source code available from the device driver.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Calling g_fmt before s_fmt resulted in a NULL pointer dereference as no
default formats were being selected on probe.
Reported-by: NNémeth Márton <nm127@freemail.hu>
Signed-off-by: NPawel Osciak <p.osciak@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Issuing a GET_MIN request on the power line frequency control times out
on at least the Apple iSight. As the UVC specification doesn't list
GET_MIN/MAX/RES as supported on that control, remove them from the
uvc_ctrls array.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add a short delay when stopping the decoder, allowing it to settle and
preventing some unexpected interaction with other firmware commands.
Signed-off-by: NIan Armstrong <ian@iarmst.demon.co.uk>
Tested-by: NMartin Dauskardt <martin.dauskardt@gmx.de>
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Hauppauge EEPROM tuner code 168 has recently shown up on HVR-1600 TV
capture cards supported by the cx18 driver.  This change allows analog
tuner type autodetection to succeed for these cards.

Information for decoding tuner code 168 was provided by Hauppauge.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMuralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Actually OMAP doesn't support scatter-gather DMA for
Display subsystem but due to legacy coding it has been overlooked
till now.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMuralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Changes -
	- Kconfig option dependancy changed to ARCH_OMAP2/3 from
	ARCH_OMAP24XX/34XX
	- There are some moments of function from omap_dss_device
	to omap_dss_driver. Incorporated changes for the same.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMuralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Then it will first check x86_platforms's i8042 detection result,
then go on with normal probe.
Signed-off-by: NFeng Tang <feng.tang@intel.com>
LKML-Reference: <4c34dd482753bb8f1@agluck-desktop.sc.intel.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>
Acked-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

This reverts commit 0b28bac5.

After adding x86_platform's detection for i8042 controller, we
don't need the force dependency on !X86_MRST any more

Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NFeng Tang <feng.tang@intel.com>
LKML-Reference: <1278342202-10973-5-git-send-email-feng.tang@intel.com>
Acked-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

This reverts commit 685afae0.

After adding x86_platform's detection for i8042 controller, we
don't need the force dependency on !X86_MRST any more

Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: NFeng Tang <feng.tang@intel.com>
LKML-Reference: <1278342202-10973-4-git-send-email-feng.tang@intel.com>
Acked-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 drivers/net/sb1250-mac.c |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original KERN_CRIT will mess up terminals.

CC: Sreenivasa Honnur <Sreenivasa.Honnur@neterion.com>
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix missing iounmaps.
Signed-off-by: NDenis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't currently update the DPMS status of the connector (both in the
connector itself and the connector's DPMS property) in the fb helper
code.  This means that if the kernel FB core has blanked the screen,
sysfs will still show a DPMS status of "on".  It also means that when X
starts, it will try to light up the connectors, but the drm_crtc_helper
code will ignore the DPMS change since according to the connector, the
DPMS status is already on.

Fixes https://bugs.freedesktop.org/show_bug.cgi?id=28436 (the annoying
"my screen was blanked when I started X and now it won't light up" bug).
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Connectors with a shared ddc line can be connected to different
encoders.

Reported by Pasi Kärkkäinen <pasik@iki.fi> on dri-devel
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Repeated ttm_page_alloc_init/fini fails noisily because the pool
manager kobj isn't zeroed out between uses (we could do just that but
statically allocated kobjects are generally considered a bad thing).
Move it to kzalloc'ed memory.

Note that this patch drops the refcounting behavior of the pool
allocator init/fini functions: it would have led to a race condition
in its current form, and anyway it was never exploited.

This fixes a regression with reloading kms modules at runtime, since
page allocator was introduced.
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Sumeet Lahorani <sumeet.lahorani@oracle.com> reported that the IPoIB
child entries are world-writable; however we don't want ordinary users
to be able to create and destroy child interfaces, so fix them to be
writable only by root.
Signed-off-by: NOr Gerlitz <ogerlitz@voltaire.com>
Cc: <stable@kernel.org>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

If qib_init() fails, the driver fails to free memory, unregister
device files, and unregister with the PCIe framework. The driver will
unload without error but a subsequent driver load will cause the
system to panic.  This was found by changing the 7220 code to load the
serdes microcode separately and not installing the microcode file.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Workqueues aren't exactly equivalent to tasklets since the callback
function may be called from multiple CPUs before the callback returns.
This causes completion notification callbacks to have MT bugs since
they weren't expecting this behavior. The fix is to use a single
threaded work queue.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The hardware error register needs to be cleared or another interrupt
will be generated, thus causing an infinite loop.  This is a
regression introduced when removing debug output.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The eager buffers are not being cleared before being mmapped into a
new user address space.  This is a potential security risk and should
be fixed.  Note that the eager header queue is already being cleared.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The HCA checks for certain hardware errors which can be falsely
triggered when the IB link is reset. The fix is to mask them rather
than report them.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Don't set write combining via PAT on the VL15 buffers to avoid a rare
problem with unaligned writes from interrupt-flushed store buffers.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>